Search Results

A dynamic computer model of automotive air conditioning systems was developed. The model uses simulation software for the coding of 1-D heat transfer, thermodynamics, fluid flow, and control valves. The same software is used to model 3-D solid dynamics associated with mechanical mechanisms of the compressor. The dynamics of the entire AC system is thus simulated within the same software environment. The results will show the models potential applications in component and system design, calibration and control.

Accurate evaluation of vehicles' transient total power requirement helps achieving further improvements in vehicle fuel efficiency. When operated, the air-conditioning (A/C) system is the largest auxiliary load on a vehicle, therefore accurate evaluation of the load it places on the vehicle's engine and/or energy storage system is especially important. Vehicle simulation models, such as "Autonomie," have been used by OEMs to evaluate vehicles' energy performance. However, the load from the A/C system on the engine or on the energy storage system has not always been modeled in sufficient detail. A transient A/C simulation tool incorporated into vehicle simulation models would also provide a tool for developing more efficient A/C systems through a thorough consideration of the transient A/C system performance. The dynamic system simulation software MATLAB/Simulink® is frequently used by vehicle controls engineers to develop new and more efficient vehicle energy system controls.

The purpose of this paper is to present a common sense practical method for establishing and demonstrating reliability objectives. In particular, this paper will: describe an operational definition of “useful life”, describe an accelerated laboratory test procedure for demonstrating that products meet the useful life objective, and describe a method for demonstrating correlation between customer usage and laboratory testing.

This paper discusses our experiences on the implementation and benefits of using the Hardware-In-the-Loop (HIL) systems for Powertrain control system software verification and validation. The Visteon HIL system integrated with several off-the-shelf diagnostics and calibration tools is briefly explained. Further, discussions on test automation sequence control and failure insertion are outlined The capabilities and advantages of using HIL for unit level software testing, open loop and closed-loop system testing, fault insertion and test automation are described. HIL also facilitates Software and Hardware Interface validation testing with low-level driver and platform software. This paper attempts to show the experiences with and capabilities of these HIL systems.

Occupant head impact simulations on automotive instrument panels (IP) are routinely performed as part of an integrated design process during the course of IP development. Based on the requirements (F/CMVSS, ECE), head impact zones on the IP are first established, which are then used to determine the various “hit” locations to be tested/analyzed. Once critical impact locations are identified, CAE simulations performed which is a repetitive process that involves computing impact angles, positioning the rigid head form with an assigned initial velocity and defining suitable contacts within the finite element model. A commercially available CAE process automation tool was used to automate these steps and generate a head impact simulation model. Once the input model is checked for errors by the automated process, it can be submitted to a solver without any user intervention for analysis and report generation.

Flow noise from automotive HVAC (Heating, Ventilating and Air Conditioning) systems is one of the major considerations of occupant comfort. The noise generated at high blower speed is a major contributor to the vehicle interior noise. This paper reviews automotive HVAC air rush noise prediction models for estimating register, buck (air handling subsystem) and vehicle noise levels. The vehicle noise prediction method correlates well with measured noise levels at driver right ear location: with a standard deviation of 1.31 dB where standard deviation is the difference between measured and predicted noise levels for a sample size of 10 vehicles.

Computational Fluid Dynamics (CFD) is an integral part of product development at Visteon Climate Systems with a validated set of CFD tools for airflow and thermal management processes. As we increasingly build CAE capabilities to design not only thermal comfort, but quiet systems, developing noise prediction capabilities becomes a high priority. Two Broadband Noise Source (BNS) models will be presented, namely Proudman's model for quadrupole source and Curle's boundary layer model for dipole source. Both models are derived from Lighthill's acoustic analogy which is based on the Navier-Stokes equations. BNS models provide aeroacoustic tools that are effective in screening air handling systems with higher noise levels and identifying components or surfaces that generate most of the noise, hence providing opportunities for early design changes. In this paper, BNS models were used as aeroacoustic design tools to redesign an automotive HVAC center duct with high levels of NVH.

Welding is one of the most commonly used fabrication method in various automotive applications. Welding is a metallurgical fusion process in which parts or work pieces to be joined are heated above their melting temperature and then solidified. Some of the effects of the welding include residual stresses and Heat Affected Zone (HAZ). A methodology is proposed to study the welding process using the commercial finite element software, ABAQUS. Non linear transient heat transfer analysis is used. Effects of heat energy input rate and heat input time on residual stresses and HAZ are determined.

Customer clinics and surveys have revealed the increased importance to the customer of good defrost and demist performance in their vehicle. Achieving this level of performance, within the time and cost constraints of a modern vehicle development program, places increased reliance on computational (CAE) techniques. However, this paper describes how the optimum development process should be to combine this reliance upon CAE methods with a newly developed experimental technique. This new laser Doppler velocimetry (LDV) based methodology is employed at all stages of the development process and complements the CAE techniques perfectly. The end result is optimized airflow management within the vehicle cabin – essential if good defrost and demist performance is to be achieved in a vehicle.

This paper introduces the Driver Stability System (DSS) at Visteon. DSS is a new active comfort / safety system for automobiles which controls the seat bolsters independently in real time to enhance the lateral support of the occupants. Under turning maneuvers, DSS reacts to the vehicle dynamics to provide an increased contact area between the occupants and their seats, allowing optimal occupant location with respect to such variables as steering wheel angle, lateral acceleration, yaw rate, and vehicle velocity. The lateral force compensation is directly coupled to the dynamic movement of vehicle chassis and the change of road profile. The system consists of the seat bolster assembly including DC motors, wheel speed sensors, steering wheel sensor, lateral accelerometer, yaw rate sensor, and electronic control unit (ECU). This paper also discusses the control concept of DSS and its realistic controller structure.

Same of the more enticing and productive opportunities to a useful work in product assurance are those of influencing the design of a product. The primary concern of design assurance is preventing or correcting those design errors that lead to poor product integrity. One of the tools used by the development teams in many organizations is the Design Review. The impact in cost and quality is directly affected by the correct utilization of the tool.

There are many opportunities in a current automotive HVAC case for improved performance, and cost savings. Based on these opportunities, a new HVAC case design has been developed. This new design is smaller and lighter than current cases while meeting many of the performance requirements. The case also features a unique plenum design for air distribution to the three modes, panel, floor, and defrost. The results of simulation and laboratory testing confirmed the concept of the new HVAC design.

Evaporators for automotive air-conditioning systems are being coated externally to improve corrosion resistance, water drainage, and reduce potential odor concerns. The coating durability and efficiency in achieving its corrosion resistance depends on the coating uniformity and adhesion characteristics. Good coating adhesion on aluminum surface can be achieved after freeing the surface from the oxide and flux residues. Evaporators manufactured by the Controlled Atmosphere Brazing (CAB) process have flux residue remaining on the surface, the presence of which interferes with the coating process and also affects the performance of coated components. A methodology to quantify the effect of high Nocolok flux residue on heat exchanger coating uniformity has been presented.

1.0 During the warm up process of the coolant in automotive heater systems physical properties such as the density, dynamic viscosity, kinematic viscosity, specific heat and thermal conductivity vary with temperature. To conduct any heater analysis, therefore, it is essential that such variations with temperatures be evaluated. In the present paper a comprehensive literature search is conducted for the published physical properties of the automotive coolants ethylene glycol and propylene glycol. The data are analyzed and compared, and equations describing the variation of the above named physical properties with temperature are derived and presented. The effect of the temperature on the internal heat transfer coefficient is discussed. A comparison of the heat transfer performance between the two glycol coolants is presented. The temperature range studied extends from - 35 to at least 125 degree Celsius.

Recycled resins can meet performance requirements on products which were initially designed for virgin materials. Olefinic instrument panel (I/P) scrap is being recycled from the Mazda Tribute and the Ford Escape into glove box bins. As a result, a quality part is being supplied to the customer and Visteon's Saline Plant has realized both increased plant operating efficiencies and landfill cost avoidance. The development process is described including: plant regrind sources, part molding and testing.

With increasingly stringent emissions regulations and concurrent requirements for enhanced engine thermal efficiency, a comprehensive characterization of the automotive gasoline fuel spray has become essential. The acquisition of accurate and repeatable spray data is even more critical when a combustion strategy such as gasoline direct injection is to be utilized. Without industry-wide standardization of testing procedures, large variablilities have been experienced in attempts to verify the claimed spray performance values for the Sauter mean diameter, Dv90, tip penetration and cone angle of many types of fuel sprays. A new SAE Recommended Practice document, J2715, has been developed by the SAE Gasoline Fuel Injection Standards Committee (GFISC) and is now available for the measurement and characterization of the fuel sprays from both gasoline direct injection and port fuel injection injectors.

In today's global economy, the automotive design engineer's responsibilities are made more complex by the differences between regulatory requirements of the various global markets. This paper compares instrument panel head impact requirements of FMVSS 201 with its European counterparts, ECE 21, and EEC/74/60, Interior Fittings. It describes the similarities and differences between these regulations and explains the unique requirements for each market. It then compares processes for development and validation testing in both markets. It also covers related topics like self-certification, witness testing, radii, projections, and interior compartment doors. The cockpit design engineer will gain an understanding of the factors involved in ensuring that their design fully meets the requirements of the subject regulations.

Traditionally, the passenger airbag door for an instrument panel (I/P) is a separate component assembled to the substrate, where the panel has an opening for the airbag module. The airbag door (usually made of TPE material) arrives to the assembly line from the airbag module supplier to be installed to the I/P. The grain and gloss between the door cover and the I/P class “A” surface must match closely. This paper describes the implementation of the passenger airbag door as an integral part of the instrument panel. This approach provides superior craftsmanship to the vehicle interior system. The I/P area that contains the seamless passenger airbag is weakened from the B-surface.

Occupant knee impact simulations are performed in the automotive industry as an integrated design process during the course of instrument panel (IP) development. All major automakers have different categories of dynamic testing methods as part of their design process in validating their designs against the FMVSS 208 requirement. This has given rise to a corresponding number of knee impact simulations performed at various stages of product development. This paper investigates the advantages and disadvantages of various types of these knee impact simulations. Only the knee load requirement portion of the FMVSS208 is considered in this paper.

This paper presents an unambiguous and intuitive method for identification of steering column resonant (SCR) mode of vibration. One simple but overlooked technique to determine the SCR mode in-vehicle is to provide local stiffnesses of the body locations where the Instrument Panel (IP) attaches, to the IP suppliers to be used in their design and development. This paper describes how this technique is useful in predicting the first few important in-vehicle steering column modes for different classes of vehicles, with examples presented in each class. The results obtained from such analyses are compared against those from direct in-buck simulations. This technique is not limited to its application in developing IP systems, but can easily be extended to include other systems such as seats, fuel tanks, etc. Also it is shown that a design optimization analysis may be performed using these attachment stiffnesses as design variables resulting in a system level solution.