Search Results

Abstract In recent years, lean-burn gasoline Spark-Ignition (SI) engines have been a major subject of investigations. With this solution, in fact, it is possible to simultaneously reduce NOx raw emissions and fuel consumption due to decreased heat losses, higher thermodynamic efficiency, and enhanced knock resistance. However, the real applicability of this technique is strongly limited by the increase in cyclic variation and the occurrence of misfire, which are typical for the combustion of homogeneous lean air/fuel mixtures. The employment of a Pre-Chamber (PC), in which the combustion begins before proceeding in the main combustion chamber, has already shown the capability of significantly extending the lean-burn limit. In this work, the potential of an ultralean PC SI engine for a decisive improvement of the thermal efficiency is presented by means of numerical and experimental analyses.

Abstract Due to the increasing requirements for efficiency, the wide range of characteristics and the improved possibilities of modern development and production processes, compressors in turbochargers have become more individualized in order to adapt to the requirements of internal combustion engines. An understanding of the working mechanisms as well as an understanding of the way that losses occur in the flow allows a reduced development effort during the optimization process. This article presents three-dimensional (3D) Computational Fluid Dynamics (CFD) investigations of the loss mechanisms and quantitative calculations of individual losses. The 3D-CFD method used in this article will reduce the drawbacks of one-dimensional calculation as far as possible. For example, the twist of the blades is taken into account and the “discrete” method is used for loss calculation instead of the “average” method.

Abstract Regulations limiting GreenHouse Gases (GHG) from Heavy-Duty (HD) commercial vehicles in the United States (US) and European Union will phase in between the 2024 and 2030 model years. These mandates require efficiency improvements at both the engine and vehicle levels, with the most stringent reductions required in the heaviest vehicles used for long-haul applications. At the same time, a 90% reduction in oxides of nitrogen (NOx) will be required as part of new regulations from the California Air Resources Board. Any technologies applied to improve engine efficiency must therefore not come at the expense of increased NOx emissions. Research into advanced engine architectures and components has identified improved turbomachine efficiency as one of the largest potential contributors to engine efficiency improvement. However this comes at the cost of a reduced capability to drive high-pressure Exhaust Gas Recirculation (EGR).

Abstract In the United States (USA), transportation is the largest single source of greenhouse gas (GHG) emissions, representing 27% of total GHGs emitted in 2020. Eighty-three percent of these came from road transport, and 57% from light-duty vehicles (LDVs). Internal combustion engine (ICE) vehicles, which still form the bulk of the United States (US) fleet, struggle to meet climate change targets. Despite increasingly stringent regulatory mechanisms and technology improvements, only three US states have been able to reduce their transport emissions to the target of below 1990 levels. Fifteen states have made some headway to within 10% of their 1990 baseline. Largely, however, it appears that current strategies are not generating effective results. Current climate-change mitigation measures in road transport tend to be predominantly technological.

Abstract This article presents an investigation of energy transfer, flame propagation, and emissions formation mechanisms in a four-cylinder, downsized and boosted, spark ignition engine fuelled by either directly injected compressed natural gas (DI CNG) or gasoline (GDI). Three different charge preparation strategies are examined for both fuels: stoichiometric engine operation without external dilution, stoichiometric operation with external exhaust gas recirculation (EGR), and lean burn. In this work, experiments and engine modelling are first used to analyze the energy transfer throughout the engine system. This analysis shows that an early start of fuel injection (SOI) improves fuel efficiency through lower unburned fuel energy at low loads with stoichiometric DI CNG operation.

Abstract The equivalent consumption minimization strategy (ECMS) is an instantaneous optimization method implemented online for hybrid electric vehicles (HEVs) to improve fuel economy. To fulfill the near-optimal performance of ECMS, equivalent factors (EFs) must be well tuned for different powertrains and driving cycles. This study proposes a hierarchical offline optimization framework which tunes the penalty value of state of charge (SOC) balance in the outer layer and optimizes EFs based on heuristic algorithms in the inner layer. A comprehensive analysis is conducted to evaluate three heuristic algorithms, including the genetic algorithm (GA), the nonlinear-inertia-decreasing particle swarm optimization algorithm (NLPSO), and the novel firefly algorithm (FA). The traversal optimization method (TOM) is chosen as the benchmark. Besides, a sensitivity analysis is carried out to reveal the impact of the penalty value on the battery SOC balance.

Abstract Electric power steering (EPS) systems have become the most advantageous steering system used in vehicles. They provide better fuel efficiency and a more compact design over traditional hydraulic power steering (HPS) systems. However, EPS systems are afflicted with unwanted noise and vibration that can undermine the safety of drivers. This article presents a mathematical framework for vibration analysis in a column-type EPS system. The steering column is modeled as a continuous clamped column. The equations of motion are derived using Hamilton’s principle, and explicit expressions are presented for the frequency and transmissibility equations. A three-degrees-of-freedom (3-DOF) dynamic model is also presented by an approximation of the stiffness, damping, and mass of the steering column. The results of the proposed analytical models are validated using ANSYS simulation.

Abstract The article presents a concept of a new turbine engine in the field of pressure gain combustion (PGC). The engine operates according to the Humphrey thermodynamic cycle, where pressure increase was obtained in a combustion chamber closed with a valve. The intake mushroom valve and exhaust swing valve were designed for self-acting. They operate as a result of gas pressure and centrifugal force. The engine consists of two rotating combustion chambers and a counterrotating radial turbine, in both of which mechanical power was generated. The gas flow in the mobile valve system, combustion process, gas expansion, and torque generation were analyzed by means of Computational Fluid Dynamics (CFD) analysis. The investigated engine concept is characterized by significant energy efficiency.

Abstract This work presents a generalized methodology for the optimal thermal management of different powertrain devices. The methodology is based on the adoption of an electrically driven pump and on the development of a specifically designed controller algorithm. This is achieved following a Model Predictive Control approach and requires a generalized lumped-parameters model of the thermal exchange between the device walls and the coolant. The methodology is validated at a test rig, with reference to a four-cylinder spark-ignition engine. Results show that the proposed approach allows a reduction in fuel consumption of about 2-3% during the engine warm-up, a decrease in fuel consumption of about 1-2% during fully warmed operation, and an estimated fuel consumption reduction of about 2.5-3% in an NEDC. Finally, the investigation highlights that the proposed approach reduces the risk of after-boiling when the engine is rapidly switched off after a prolonged high-load operation.

Abstract A pre-chamber ignition system has the potential to reduce the burn duration of lean-burn gasoline engine combustion and can achieve a reduced knock occurrence from the distributed ignition sources. Pre-chamber ignition produces high-velocity turbulent jets, and these jets often reach sonic velocity and produce shock waves inside the combustion chamber. These shock waves make knock detection difficult with a conventional surface-mounted acoustic knock sensor. This article discusses how an acoustic knock sensor works with a pre-chamber ignition and evaluates different cylinder pressure-based knock detection strategies and proposes a method that eliminates the influence of jet-induced oscillations on knock detection.

Abstract Deep learning (DL)-based approaches enable unprecedented control paradigms for propulsion systems, utilizing recent advances in high-performance computing infrastructure connected to modern vehicles. These approaches can be employed to optimize diesel aftertreatment control systems targeting the reduction of emissions. The optimization of the Trapped Soot Load (TSL) reduction in the Diesel Particulate Filter (DPF) is such an example. As part of the diesel aftertreatment system, the DPF stores the soot particles resulting from the combustion process in the engine. Periodically, the stored soot is oxidized during a DPF regeneration event. The efficiency of such a regeneration influences the fuel economy, and potentially the service interval of the vehicle. The quality of a regeneration depends on the operating conditions of the DPF, the engine, and the ability to complete the regeneration event.

Abstract Demonstrating ring pack operation in an operating engine is very difficult, yet it is essential to optimize engine performance parameters such as blow-by, oil consumption, emissions, and wear. A significant amount of power is lost in friction between piston ring–cylinder liner interfaces if ring pack parameters are not optimized properly. Thus, along with these parameters, it is also necessary to reduce friction power loss in modern internal combustion engines as the oil film thickness formed between the piston ring and liner is vital for power loss reduction due to friction. Hence, it has also been a topic of research interest for decades. Piston and ring dynamics simulation software are used extensively for a better ring pack design. In this research work, a similar software for piston ring dynamics simulation reviews the ring pack performance of a four-cylinder diesel engine.

Abstract Linear internal combustion engine-linear generator integrated system (LICELGIS) is an innovative energy conversion device with the ability of converting mechanical energy into electrical energy, which allows it to be a range extender for hybrid vehicles. This article presents a fundamental analysis for the steady-state operation of the LICELGIS, concentrating on electromagnetic force and motion characteristics. Simple assumptions are made to represent ideal gases instantaneous heat release and rejection. Based on assumptions, sensitivity analysis is carried out for key factors of electromagnetic force. The theoretical velocity model in mathematics is derived from analyzing the LICELGIS theory model. It shows that fuel injection quantity and stroke length are the most sensitive factors in key parameters. The piston velocity around the top dead center (TDC) changes greater than that at any other position, which is caused by the combustion process.

Abstract Mechanical friction simulations offer a valuable tool in the development of internal combustion engines for the evaluation of optimization studies in terms of time efficiency. However, system modeling and evaluation of model performance may be highly complex. A high number of interacting submodels and parameters as well as a limited model transparency contribute to uncertainties in the modeling process. In particular, model calibration and validation are complicated by the unknown effect of parameters on the model output. This article presents an advanced and model-independent methodology for identifying sensitive parameters of engine friction. This allows the user to investigate an unlimited number of parameters of a model whose structure and properties are prior unknown.

Abstract One of the key factors for accurate mass burn fraction and energy conversion point calculations is the accuracy of the compression ratio. The method presented in this article suggests a workflow that can be applied to determine or correct the compression ratio estimated geometrically or measured using liquid displacement. It is derived using the observation that, in a motored engine, the heat losses are symmetrical about a certain crank angle, which allows for the derivation of an expression for the clearance volume [1]. In this article, a workflow is implemented in real time, in a current production engine indicating system. The goal is to improve measurement data quality and stability for the energy conversion points calculated during measurement procedures. Experimental and simulation data is presented to highlight the benefits and improvement that can be achieved, especially at the start of combustion.

Abstract Turbocharging can provide a low cost means for increasing the power output and fuel economy of an internal combustion engine. Currently, turbocharging is common in multi-cylinder engines, but due to the inconsistent nature of intake air flow, it is not commonly used in single-cylinder engines. In this article, we propose a novel method for turbocharging single-cylinder, four-stroke engines. Our method adds an air capacitor-an additional volume in series with the intake manifold, between the turbocharger compressor and the engine intake-to buffer the output from the turbocharger compressor and deliver pressurized air during the intake stroke. We analyzed the theoretical feasibility of air capacitor-based turbocharging for a single-cylinder engine, focusing on fill time, optimal volume, density gain, and thermal effects due to adiabatic compression of the intake air.

Abstract Nowadays, the need for a more sustainable mobility is fostering powertrain electrification as a way of reducing the carbon footprint of conventional vehicles. On the other side, the presence of multiple energy sources significantly increases the powertrain complexity and requires the development of a suitable Energy Management System (EMS) whose performance can strongly affect the fuel economy potential of the vehicle. In such a framework, this article proposes a novel methodology to reverse engineer the control strategy of a test case P2 Plug-in Hybrid Electric Vehicle (PHEV) through the analysis of experimental data acquired in a wide range of driving conditions. In particular, a combination of data obtained from On-Board Diagnostic system (OBD), Controller Area Network (CAN)-bus protocol, and additional sensors installed on the High Voltage (HV) electric net of the vehicle is used to point out any dependency of the EMS decisions on the powertrain main operating variables.

Abstract Two new misfire detection indexes for single-cylinder motorcycle engines—dubbed gap distance (GD) and gap slope (GS)—are proposed in this study. GD and GS quantify the change in engine angular acceleration using the tooth time measured by the crankshaft position sensor (CKPS). GD is defined as the product of the spacing distance I (the distance from the top dead center at the explosion stroke [TDC2] to the engine speed trend line parallel to the engine speed axis) and spacing distance II (the distance from the bottom dead center at the expansion stroke [BDC2] to the engine speed trend line parallel to the engine speed axis). GS is defined as the difference between the two slopes between the engine speed inclination line and the engine speed trend line. Here the engine speed trend line connects two engine speeds at the top dead center at the intake stroke (TDC1) of the current and subsequent cycles.

Abstract Technological advancements and growth in electric motors and battery packs enable vehicle propulsion electrifications, which minimize the need for fossil fuel consumption. The mobility shift to electric motors creates a demand for an efficient electric motor thermal management system that can accommodate heat dissipation needs with minimum power requirements and noise generation. This study proposes an intelligent hybrid cooling system that includes a gravity-aided passive cooling solution coupled with a smart supplementary liquid cooling system. The active cooling system contains a radiator, heat sink, variable frequency drive, alternating current (AC) fan, direct current (DC) pump, and real-time controller. A complete nonlinear mathematical model is developed using a lumped parameter approach to estimate the optimum fan and pump operations at each control interval.

Abstract Three-dimensional patterns representing crosshatched plateau-honed cylinder bores based on two-dimensional Fast Fourier Transform (FFT) of measured surfaces were generated and used to calculate pressure flow, shear-driven flow, and shear stress factors. Later, the flow and shear stress factors obtained by numerical simulations for various surface patterns were used to calculate lubricant film thickness and friction force between piston ring and cylinder bore contact in typical diesel engine conditions using a mixed lubrication model. The effects of various crosshatch honing angles, such as 30°, 45°, and 60°, and texture heights on engine friction losses, wear, and oil consumption were discussed in detail. It is observed from numerical results that lower lubricant film thickness values are generated with higher honing angles, particularly in mixed lubrication regime where lubricant film thickness is close to the roughness level, mainly due to lower resistance to pressure flow.