Search Results

Abstract In recent years, lean-burn gasoline Spark-Ignition (SI) engines have been a major subject of investigations. With this solution, in fact, it is possible to simultaneously reduce NOx raw emissions and fuel consumption due to decreased heat losses, higher thermodynamic efficiency, and enhanced knock resistance. However, the real applicability of this technique is strongly limited by the increase in cyclic variation and the occurrence of misfire, which are typical for the combustion of homogeneous lean air/fuel mixtures. The employment of a Pre-Chamber (PC), in which the combustion begins before proceeding in the main combustion chamber, has already shown the capability of significantly extending the lean-burn limit. In this work, the potential of an ultralean PC SI engine for a decisive improvement of the thermal efficiency is presented by means of numerical and experimental analyses.

Abstract Turbocharging can provide a low cost means for increasing the power output and fuel economy of an internal combustion engine. Currently, turbocharging is common in multi-cylinder engines, but due to the inconsistent nature of intake air flow, it is not commonly used in single-cylinder engines. In this article, we propose a novel method for turbocharging single-cylinder, four-stroke engines. Our method adds an air capacitor-an additional volume in series with the intake manifold, between the turbocharger compressor and the engine intake-to buffer the output from the turbocharger compressor and deliver pressurized air during the intake stroke. We analyzed the theoretical feasibility of air capacitor-based turbocharging for a single-cylinder engine, focusing on fill time, optimal volume, density gain, and thermal effects due to adiabatic compression of the intake air.

Abstract Two new misfire detection indexes for single-cylinder motorcycle engines—dubbed gap distance (GD) and gap slope (GS)—are proposed in this study. GD and GS quantify the change in engine angular acceleration using the tooth time measured by the crankshaft position sensor (CKPS). GD is defined as the product of the spacing distance I (the distance from the top dead center at the explosion stroke [TDC2] to the engine speed trend line parallel to the engine speed axis) and spacing distance II (the distance from the bottom dead center at the expansion stroke [BDC2] to the engine speed trend line parallel to the engine speed axis). GS is defined as the difference between the two slopes between the engine speed inclination line and the engine speed trend line. Here the engine speed trend line connects two engine speeds at the top dead center at the intake stroke (TDC1) of the current and subsequent cycles.

Abstract Three-dimensional patterns representing crosshatched plateau-honed cylinder bores based on two-dimensional Fast Fourier Transform (FFT) of measured surfaces were generated and used to calculate pressure flow, shear-driven flow, and shear stress factors. Later, the flow and shear stress factors obtained by numerical simulations for various surface patterns were used to calculate lubricant film thickness and friction force between piston ring and cylinder bore contact in typical diesel engine conditions using a mixed lubrication model. The effects of various crosshatch honing angles, such as 30°, 45°, and 60°, and texture heights on engine friction losses, wear, and oil consumption were discussed in detail. It is observed from numerical results that lower lubricant film thickness values are generated with higher honing angles, particularly in mixed lubrication regime where lubricant film thickness is close to the roughness level, mainly due to lower resistance to pressure flow.

Abstract The Formula SAE (FSAE) is an international engineering competition where a Formula style race car is designed and built by students from worldwide universities. According to FSAE regulation, an air restrictor with circular cross section of 20 mm for gasoline-fuelled and 19 mm for E-85-fuelled vehicles is to be incorporated between the throttle valve and engine inlet. The sole purpose of this regulation is to limit the airflow to the engine used. The only sequence allowed is throttle valve, restrictor and engine inlet. A new approach of combining ram theory and acoustic theory methods are investigated to increase the performance of the engine by designing an optimized intake runner for a particular engine speed range and an optimized plenum volume in this range. Engine performance characteristics such as brake power, brake torque and volumetric efficiency are taken into considerations.

Abstract Stratified lean combustion has proven to be a promising approach for further increasing the thermal efficiency of gasoline direct injection engines in low load conditions. In this work, a new injection strategy for stratified operation mode is introduced. A side and a central-mounted solenoid multi-hole injector are simultaneously operated in a single-cylinder engine. Thermodynamic investigations show that this concept leads to improved stability, faster combustion, reduced particle number emissions, and lower fuel consumption levels compared to using only one injector. Experiments at an optical engine and three-dimensional computational fluid dynamics (CFD) simulations explain the improvements by a more compact mixture and reduced piston wetting with two injectors. Finally, the application of external EGR in combination with the above concept allows NOx emissions to be effectively kept at a low level while maintaining a stable operation.

Abstract Realizing the potential of the gasoline direct injection (GDI) concept lies in effectively stratifying the charge at different engine operating conditions. This is generally obtained by properly directing the air and fuel through carefully oriented intake port(s) and fuel spray and appropriately changing injection parameters. However, robust methods of charge stratification are essential to extend the lean operating range, particularly in small GDI engines. In this work, a novel piston shape was developed for a 200 cm3, single-cylinder, four-stroke gasoline engine to attain charge stratification. Stratification of charge is achieved even when the fuel was injected early in the intake stroke by a specially shaped wedge on the piston crown that produced twin vortices during compression and physically separated the charge into two sides in the combustion chamber.

Abstract Mankind’s quest for clean alternative energy sources pushes the boundaries of science and technology every passing day. Increasing environmental and human health concerns caused by conventional fuels underscores the importance of identifying an energy source which is sustainable in terms of production, emissions, and wide application. Hythane (hydrogen-methane gas) is a contender for applications ranging from transportation and combined heating-power generation to cooking. In land transportation, the use of gaseous hythane for internal combustion engines shows better performance, enhanced combustion, and lower emission than conventional liquid hydrocarbon fuels. The use of liquefied Natural Gas (NG) and hydrogen in aircraft and ships is a steppingstone to more the wide-scale use of hythane in air, sea, and rail transportation sectors which could lower emissions and operating costs.

Abstract Many consider hydrogen to be the automobile fuel of the future. Indeed, it has numerous characteristics that makes it very attractive. Hydrogen has a much higher energy density than gasoline, can be produced from water, and its only emission is water. However, there are numerous challenges associated with hydrogen. In particular, the production of hydrogen is a key issue. Currently, most hydrogen is developed from methane, resulting in hydrogen having a carbon footprint. New investments into electrolysis from renewable energy sources is showing promise as an alternative for generating hydrogen. Further, the distribution of hydrogen poses many problems, requiring substantial infrastructure to support a hydrogen economy. Additionally, hydrogen storage is a key issue since most conventional storage mechanisms are overly bulky. If these three issues can be addressed, hydrogen is posed for being a key fuel as the world tries to move away from fossil fuels.

Abstract Evaluating the effects of deposits formed in existing engines on their performance is essential, particularly for gasoline direct injection (GDI) engines, wherein such deposits can be even more problematic. Furthermore, it has been suggested that some gasoline detergent additives (GDAs) may increase combustion chamber deposit (CCD) formation. However, there is a lack of data available regarding CCD formation in GDI engines, and there are no systematic investigations of the effects of the relationship between detergent additives and CCD formation on the GDI engines operation. Thus, the aim of this article was to critically review the existing literature on the effects of the deposit buildup associated with GDAs on the knocking performance, emissions, and operational properties of GDI engines. Surveyed studies showed that, GDI engines produce higher amounts of CCDs compared with port fuel injection (PFI) engines.

Abstract In this study low temperature plasma technology was applied to expand auto-ignition operation region and control auto-ignition phasing of the homogeneous charge compression ignition (HCCI) combustion. The low temperature plasma igniter of a barrier discharge model (barrier discharge igniter (BDI)) with high-frequency voltage (15 kHz) was provided at the top center of the combustion chamber, and the auto-ignition characteristics of the HCCI combustion by the low temperature plasma assistance was investigated by using a single-cylinder gasoline engine. HCCI combustion with compression ratio of 15:1 was achieved by increasing the intake air temperature. The lean air-fuel (A/F) ratio limit and visualized auto-ignition combustion process on baseline HCCI without discharge assistance, spark-assisted HCCI, and BDI-assisted HCCI were compared.

Abstract Cycle-by-cycle combustion prediction in real time during engine operation can serve as a vital input for operating at optimal performance conditions and for emission control. In this work, a real-time capable physics-based combustion model has been proposed for the prediction of the heat release rate in a direct injection diesel engine. The model extends the approaches proposed earlier in the literature by considering spray dynamics such as spray penetration and Sauter mean diameter in order to calculate the mass of evaporated fuel from the spray. Wall impingement of the liquid spray is predicted by considering the liquid length based on the prevailing in-cylinder conditions. These effects are considered even after the hydraulic end of injection till the last droplet of fuel impinges on the combustion chamber wall. The fuel evaporated from the wall film and its contribution to the kinetic energy of the charge are also considered.

Abstract Insulating combustion chamber surfaces with thermal barrier coatings (TBCs) provides thermal efficiency improvement when done appropriately. This article reports on insulation heat transfer, engine performance characteristics, and damage modelling of “temperature swing” TBCs. “Temperature swing” insulation refers to the insulation material applied on surfaces of combustion chamber walls that enables selective manipulation of its surface temperature profile over the four strokes of an engine cycle. A combined GT Suite-ANSYS Fluent simulation methodology is developed to investigate the impact of thermal properties and insulation thickness for a variety of TBC materials for its “temperature swing” characteristics. This one-dimensional transient heat conduction analyses and engine cycle simulations are performed using scaled-down thermal properties of yttria-stabilized zirconia.

Abstract Reactivity controlled compression ignition (RCCI) engines still suffer from high levels of carbon monoxide (CO) and unburned hydrocarbon (uHC) emissions at light loads, which is one of the main challenges to be overcome before its implementation in practical engines. The injection strategies and charge temperature are two important factors that affect the mixture stratification and fuel reactivity, which have a great impact on the formation of pollutants in RCCI engines. Therefore, it is of great importance to study the effect of these variables in order to support the development of RCCI engines. In this study, an experimental investigation was carried out to study the combined effect of the start of direct injection (SOI) timing and fuel temperature on RCCI combustion characteristics in a single-cylinder research engine equipped with a common rail under constant engine speed and energy delivery ratio.

Abstract Generally, homogeneous mixture combustion is preferred at high loads in conventional spark-ignition engines. But homogeneous mixture combustion can lead to high hydrocarbon (HC) emissions at low loads. Thereby, stratified mixture combustion with an overall lean mixture is preferred at low loads, which can significantly reduce HC emissions, but NOx and soot emissions will increase. Nowadays, gasoline direct injection (GDI) engines are becoming popular because of better thermal efficiency and low emissions at all loads. These engines work with a stratified mixture at low-load conditions and a homogeneous mixture at high-load conditions. But the problem with these engines is high nitrogen oxides (NOx) and soot emissions at low-load conditions. Therefore, today, the concept of partial stratification is tried in these engines, which is a combination of the combustion of stratified and homogeneous mixtures, using both GDI and port fuel injection (PFI) techniques.

Abstract Reaching the particle emissions regulatory limits for the combustion engine is a challenge for developers. Particle filters have been the standard solution to reduce particle emissions, but filters are limited in storage capacity and need to be regenerated, a process emitting more carbon dioxide (CO2) as more fuel is consumed to regenerate the filter. In previous research, it was found that the engine can emit large spikes in particle numbers (PNs) under stationary operating conditions. These spikes were several orders of magnitude higher than for the base particle emissions level and occurred seemingly at random. The source of the spikes was believed to be the cylinder-piston-ring system and as 50–99% of the particles stemmed from these spikes, the influence on the particle emissions made it an interesting investigation to find the root cause of it. The experiments were performed for different piston ring loads, locked ring positions, and different oil compositions.

Abstract Rising engine efficiency and exhaust limitations demand a deeper knowledge of the combustion process. State-of-the-art investigations use laser optical test equipment that relies on optical accesses into the engine. In this article, a new endoscopic, fully optical access for a high-speed large-bore engine is demonstrated. The successfully realized concept consists of two individually usable accesses: The lateral access with a vertical field of view is realized via a ring, which is inserted between the cylinder liner and cylinder head. The ring offers several screw-in positions for an ultraviolet (UV)-enhanced endoscope. This access can be used independently for full-load investigations of the mixture formation and combustion processes taking place inside the cylinder; The second access from above is realized by inserting a self-developed fisheye endoscope.

Abstract The design of cylinder liners, pistons, and piston rings is subject to different conflicting goals. In addition to a loss-free seal of the combustion chamber, sufficient oil must be present between the friction partners. Both the reduction of piston assembly friction and the minimization of oil consumption are crucial to achieve the strictly defined CO2 and emission standards. To master this challenge and find the best compromise requires a lot of system-specific know-how. The automobile and engine manufacturers focus mainly on friction-reducing measures, which are analyzed with different measuring methods such as the floating-liner method, the strip-down method, or the instantaneous indicated mean effective pressure (IMEP) method. However, the interpretation of the results and the development of realistic simulation models lacks information about the oil film behavior and the film thickness.

Abstract Gasoline direct-injection (GDI) engines are finding increasing applications due to their potential benefits such as low fuel consumption and superior performance. However, their use in small engines poses challenges in locating the injector and avoiding the fuel impingement on the combustion chamber walls. The selection of suitable injection timing(s) and injection of fuel in multiple pulses can overcome these difficulties. In the present work, a small-bore spray-guided GDI engine was developed by modifying a base carbureted engine. Detailed experiments and supporting CFD simulations were conducted to study the influence of the number of injections per cycle and injection timings on the performance, emissions, and combustion characteristics including cycle-to-cycle variations. It was found that the homogeneity of the fuel-air mixture was improved and fuel impingement was reduced with multiple injections.

Abstract Improving thermal efficiency of an internal combustion engine is one of the most cost-effective ways to reduce life cycle-based CO2 emissions for transportation. Lean burn technology has the potential to reach high thermal efficiency if simultaneous low NOx, HC, and CO emissions can be achieved. Low NOx can be realized by ultra-lean (λ ≥ 2) spark-ignited combustion; however, the HC and CO emissions can increase due to slow flame propagation and high combustion variability. In this work, we introduce a new combustion concept called turbulent jet-controlled compression ignition, which utilizes multiple turbulent jets to ignite the mixture and subsequently triggers end gas autoignition. As a result, the ultra-lean combustion is further improved with reduced late-cycle combustion duration and enhanced HC and CO oxidation. A low-cost passive prechamber is innovatively fueled using a DI injector in the main combustion chamber through spray-guided stratification.