Search Results

Abstract In recent years, lean-burn gasoline Spark-Ignition (SI) engines have been a major subject of investigations. With this solution, in fact, it is possible to simultaneously reduce NOx raw emissions and fuel consumption due to decreased heat losses, higher thermodynamic efficiency, and enhanced knock resistance. However, the real applicability of this technique is strongly limited by the increase in cyclic variation and the occurrence of misfire, which are typical for the combustion of homogeneous lean air/fuel mixtures. The employment of a Pre-Chamber (PC), in which the combustion begins before proceeding in the main combustion chamber, has already shown the capability of significantly extending the lean-burn limit. In this work, the potential of an ultralean PC SI engine for a decisive improvement of the thermal efficiency is presented by means of numerical and experimental analyses.

Abstract This article presents an investigation of energy transfer, flame propagation, and emissions formation mechanisms in a four-cylinder, downsized and boosted, spark ignition engine fuelled by either directly injected compressed natural gas (DI CNG) or gasoline (GDI). Three different charge preparation strategies are examined for both fuels: stoichiometric engine operation without external dilution, stoichiometric operation with external exhaust gas recirculation (EGR), and lean burn. In this work, experiments and engine modelling are first used to analyze the energy transfer throughout the engine system. This analysis shows that an early start of fuel injection (SOI) improves fuel efficiency through lower unburned fuel energy at low loads with stoichiometric DI CNG operation.

Abstract The article compares the accuracy of different exhaust gas recirculation (EGR) correction factor models under engine conditions. The effect of EGR on the laminar burning velocity of a EURO VI E10 specification gasoline (10% Ethanol content by volume) has been back calculated from engine pressure trace data, using the Leeds University Spark Ignition Engine Data Analysis (LUSIEDA) reverse thermodynamic code. The engine pressure data ranges from 5% to 25% EGR (by mass) with the running conditions, such as spark advance and pressure at intake valve closure, changed to maintain a constant engine load of 0.79 MPa gross mean effective pressure (GMEP). Based on the experimental data, a correlation is suggested on how the laminar burning velocity reduces with increasing EGR mass fraction.

Abstract This work presents a generalized methodology for the optimal thermal management of different powertrain devices. The methodology is based on the adoption of an electrically driven pump and on the development of a specifically designed controller algorithm. This is achieved following a Model Predictive Control approach and requires a generalized lumped-parameters model of the thermal exchange between the device walls and the coolant. The methodology is validated at a test rig, with reference to a four-cylinder spark-ignition engine. Results show that the proposed approach allows a reduction in fuel consumption of about 2-3% during the engine warm-up, a decrease in fuel consumption of about 1-2% during fully warmed operation, and an estimated fuel consumption reduction of about 2.5-3% in an NEDC. Finally, the investigation highlights that the proposed approach reduces the risk of after-boiling when the engine is rapidly switched off after a prolonged high-load operation.

Abstract Turbocharging can provide a low cost means for increasing the power output and fuel economy of an internal combustion engine. Currently, turbocharging is common in multi-cylinder engines, but due to the inconsistent nature of intake air flow, it is not commonly used in single-cylinder engines. In this article, we propose a novel method for turbocharging single-cylinder, four-stroke engines. Our method adds an air capacitor-an additional volume in series with the intake manifold, between the turbocharger compressor and the engine intake-to buffer the output from the turbocharger compressor and deliver pressurized air during the intake stroke. We analyzed the theoretical feasibility of air capacitor-based turbocharging for a single-cylinder engine, focusing on fill time, optimal volume, density gain, and thermal effects due to adiabatic compression of the intake air.

Abstract The hydrocarbons constituting the heavy tail of gasoline are key contributors to particulate matter (PM) emissions from spark-ignition (SI) engines. They are predominantly aromatic and, to a significant degree, bicyclic aromatic. For example, above a boiling point of 400°F, the content of bicyclic compounds in the United States (US) summer E10 regular-grade gasoline exceeds 50%v. Various gasoline parameters, such as the PM Index, Particulate Evaluation Index (PEI), Particulate and Soot Correlation Equation (PASCE), or Threshold Sooting Index (TSI), have been proposed as predictors of PM emissions from SI engines. In particular, the PM Index, whose value is dominated by the content of heavy aromatics and which, so far, has yielded the most predictive PM emissions models, appears to be the best metric to achieve this objective.

Abstract Two new misfire detection indexes for single-cylinder motorcycle engines—dubbed gap distance (GD) and gap slope (GS)—are proposed in this study. GD and GS quantify the change in engine angular acceleration using the tooth time measured by the crankshaft position sensor (CKPS). GD is defined as the product of the spacing distance I (the distance from the top dead center at the explosion stroke [TDC2] to the engine speed trend line parallel to the engine speed axis) and spacing distance II (the distance from the bottom dead center at the expansion stroke [BDC2] to the engine speed trend line parallel to the engine speed axis). GS is defined as the difference between the two slopes between the engine speed inclination line and the engine speed trend line. Here the engine speed trend line connects two engine speeds at the top dead center at the intake stroke (TDC1) of the current and subsequent cycles.

Abstract The Formula SAE (FSAE) is an international engineering competition where a Formula style race car is designed and built by students from worldwide universities. According to FSAE regulation, an air restrictor with circular cross section of 20 mm for gasoline-fuelled and 19 mm for E-85-fuelled vehicles is to be incorporated between the throttle valve and engine inlet. The sole purpose of this regulation is to limit the airflow to the engine used. The only sequence allowed is throttle valve, restrictor and engine inlet. A new approach of combining ram theory and acoustic theory methods are investigated to increase the performance of the engine by designing an optimized intake runner for a particular engine speed range and an optimized plenum volume in this range. Engine performance characteristics such as brake power, brake torque and volumetric efficiency are taken into considerations.

Abstract Stratified lean combustion has proven to be a promising approach for further increasing the thermal efficiency of gasoline direct injection engines in low load conditions. In this work, a new injection strategy for stratified operation mode is introduced. A side and a central-mounted solenoid multi-hole injector are simultaneously operated in a single-cylinder engine. Thermodynamic investigations show that this concept leads to improved stability, faster combustion, reduced particle number emissions, and lower fuel consumption levels compared to using only one injector. Experiments at an optical engine and three-dimensional computational fluid dynamics (CFD) simulations explain the improvements by a more compact mixture and reduced piston wetting with two injectors. Finally, the application of external EGR in combination with the above concept allows NOx emissions to be effectively kept at a low level while maintaining a stable operation.

Abstract Realizing the potential of the gasoline direct injection (GDI) concept lies in effectively stratifying the charge at different engine operating conditions. This is generally obtained by properly directing the air and fuel through carefully oriented intake port(s) and fuel spray and appropriately changing injection parameters. However, robust methods of charge stratification are essential to extend the lean operating range, particularly in small GDI engines. In this work, a novel piston shape was developed for a 200 cm3, single-cylinder, four-stroke gasoline engine to attain charge stratification. Stratification of charge is achieved even when the fuel was injected early in the intake stroke by a specially shaped wedge on the piston crown that produced twin vortices during compression and physically separated the charge into two sides in the combustion chamber.

Abstract This work focuses on the effects of the laminar flame speed (LFS) and flame stretch on the phenomenological modeling of the combustion process in spark ignition engines. The study is carried out using a 1D model of a small-size naturally aspirated SI engine, equipped with an external EGR circuit. The model, developed in GT-Power™ environment, includes advanced sub-models of the in-cylinder processes. The combustion is modeled using a fractal approach, where the burning rate is directly related to the laminar flame speed. A novel LFS correlation based on 1D chemical kinetics computations is presented and assessed with the experimentally derived Metghalchi and Keck correlation. Moreover, the effects of the flame stretch, evaluated according to an asymptotic theory, are properly considered in the combustion model.

Abstract Considering the biodiesel composition, blend percentage, and temperature as input variables in the models to predict biodiesel-diesel blends’ properties is imperative. However, there are no models available in the literature to predict the properties of biodiesel-diesel blends that consider all these variables. The accuracy of spray and combustion models for diesel engines depends on the accuracy at which the fuel properties are estimated. Thus, straightforward approaches to accurately predict the properties of biodiesel-diesel blends are required. A novel reference property-based approach is proposed in the present work to predict the biodiesel-diesel blends’ properties to address this research gap. Models available in the literature correlating the properties of interest to fuel temperature were modified by including a reference property measured at 293 K.

Abstract Due to the incoming phase out of fossil fuels from the market in order to reduce the carbon footprint of the automotive sector, hydrogen-fueled engines are candidate mid-term solution. Thanks to its properties, hydrogen promotes flames that poorly suffer from the quenching effects toward the engine walls. Thus, emphasis must be posed on the heat-up of the oil layer that wets the cylinder liner in hydrogen-fueled engines. It is known that motor oils are complex mixtures of a number of mainly heavy hydrocarbons (HCs); however, their composition is not known a priori. Simulation tools that can support the early development steps of those engines must be provided with oil composition and properties at operation-like conditions. The authors propose a statistical inference-based optimization approach for identifying oil surrogate multicomponent mixtures. The algorithm is implemented in Python and relies on the Bayesian optimization technique.

Abstract Mankind’s quest for clean alternative energy sources pushes the boundaries of science and technology every passing day. Increasing environmental and human health concerns caused by conventional fuels underscores the importance of identifying an energy source which is sustainable in terms of production, emissions, and wide application. Hythane (hydrogen-methane gas) is a contender for applications ranging from transportation and combined heating-power generation to cooking. In land transportation, the use of gaseous hythane for internal combustion engines shows better performance, enhanced combustion, and lower emission than conventional liquid hydrocarbon fuels. The use of liquefied Natural Gas (NG) and hydrogen in aircraft and ships is a steppingstone to more the wide-scale use of hythane in air, sea, and rail transportation sectors which could lower emissions and operating costs.

Abstract Many consider hydrogen to be the automobile fuel of the future. Indeed, it has numerous characteristics that makes it very attractive. Hydrogen has a much higher energy density than gasoline, can be produced from water, and its only emission is water. However, there are numerous challenges associated with hydrogen. In particular, the production of hydrogen is a key issue. Currently, most hydrogen is developed from methane, resulting in hydrogen having a carbon footprint. New investments into electrolysis from renewable energy sources is showing promise as an alternative for generating hydrogen. Further, the distribution of hydrogen poses many problems, requiring substantial infrastructure to support a hydrogen economy. Additionally, hydrogen storage is a key issue since most conventional storage mechanisms are overly bulky. If these three issues can be addressed, hydrogen is posed for being a key fuel as the world tries to move away from fossil fuels.

Abstract In this work, the refinement of a phenomenological turbulence model developed in recent years by the authors is presented in detail. As known, reliable information about the underlying turbulence intensity is a mandatory prerequisite to predict the burning rate in phenomenological combustion models. The model is embedded under the form of “user routine” in the GT-Power™ software. The main advance of the proposed approach is the potential to describe the effects on the in-cylinder turbulence of some geometrical parameters, such as the intake runner orientation, the compression ratio, the bore-to-stroke ratio, and the valve number. The model is based on three balance equations, referring to the mean flow kinetic energy, the tumble vortex momentum, and the turbulent kinetic energy (3-eq. concept). An extended formulation is also proposed, which includes a fourth equation for the dissipation rate, allowing to forecast also the integral length scale (4-eq. concept).

Abstract Particulate matter (PM) indices—those linking PM emissions from gasoline engines to the composition and properties of the fuel—have been a topic of significant study over the last decade. It has long been known that fuel composition has a significant impact on particulate emissions from gasoline engines. Since gasoline direct injection (GDI) engines have become the market-leading technology, this has become more significant because the evaporative behavior of fuel increases in importance. Several PM indices have been developed to provide metrics describing this behavior and correlating PM emissions. In this article, 16 different PM indices are identified and collected—to the authors’ knowledge, all of the indices are available at the time of writing. The indices are reviewed and discussed in the context of the information required to calculate them, as well as their utility.

Abstract Natural gas (NG) can be compressed to a high pressure of around 200 bar for use in engines and other applications. Compressed natural gas (CNG) contains 87–92% methane (CH4) and has a low carbon-to-hydrogen ratio compared to other hydrocarbon (HC) fuels. Due to this, it can potentially reduce carbon dioxide (CO2) emissions by more than 20% compared to conventional fuels like diesel or gasoline. This makes CNG one of the most environmentally friendly fuels for internal combustion engines (ICEs). To improve the thermal efficiency of ICEs, higher compression ratios (CRs) and leaner combustion are essential. Since CNG is a gaseous fuel, it has several advantages over liquid fuels due to its favorable physical and chemical properties. A few of these advantages are minimal fuel evaporation issues, a low-carbon content in the fuel composition and a high-octane number. The CNG high-octane number allows for a high CR, resulting in higher thermal efficiency and lower emissions.

Abstract Evaluating the effects of deposits formed in existing engines on their performance is essential, particularly for gasoline direct injection (GDI) engines, wherein such deposits can be even more problematic. Furthermore, it has been suggested that some gasoline detergent additives (GDAs) may increase combustion chamber deposit (CCD) formation. However, there is a lack of data available regarding CCD formation in GDI engines, and there are no systematic investigations of the effects of the relationship between detergent additives and CCD formation on the GDI engines operation. Thus, the aim of this article was to critically review the existing literature on the effects of the deposit buildup associated with GDAs on the knocking performance, emissions, and operational properties of GDI engines. Surveyed studies showed that, GDI engines produce higher amounts of CCDs compared with port fuel injection (PFI) engines.

Abstract The long-term use of conventional liquid energy sources for internal combustion (IC) engines has its own negative ramifications on the health of living beings and the ecosystem at large. The search for solutions to overcome these implications brings us to one of the domains of research called alternative fuels. Alternative fuels may be used to enrich or fully substitute conventional fuels. In this review, a literature study on the enrichment of a primary fuel using hydroxy gas (HOH) produced from the electrolysis of water is discussed. The experimental evidence shows that HOH induction between 5 and 10 liters per minute (lpm) enhances the results of performance parameters coupled with a decrease in emission levels except for the oxides of nitrogen (NOx). However, this shortfall is nullified using techniques such as exhaust gas recirculation (EGR) and water injection.