Search Results

Since 1978, the Agency of Industrial Science and Technology (AIST) of MITI has promoted research and development of “Large-Scale Energy Conservation Technology” popularly known as the “Moonlight Project”. As the first step, “system technology tests” using improved lead acid batteries started at Kansai Electric's Tatsumi Electric Energy Storage System Test Plant on October 1, 1986. The results showed that this system can work not only as a load-leveling apparatus but also as a high-quality power source which can support the utility power system with its load frequency control and voltage regulation capabilities. As the second step of these R&D activities, a 1MW/8MWh sodium-sulfur battery pilot plant was constructed at the same Tatsumi site. On July 11, 1991, 1000 kW× 8H facility, the largest of its type in the world, was completed and started operation. This paper describes the construction experience and operation results of the pilot plant.

General Motors Powertrain Division has developed the next generation big block V8 engine for introduction in the 1996 model year. In addition to meeting tighter emission and on-board diagnostic legislation, this engine evolved to meet both customer requirements and competitive challenges. Starting with the proven dependability of the time tested big block V8, goals were set to substantially increase the power, torque, fuel economy and overall pleaseability of GM's large load capacity gasoline engine. The need for this new engine to meet packaging requirements in many vehicle platforms, both truck and OEM, as well as a requirement for minimal additional heat rejection over the engine being replaced, placed additional constraints on the design.

In order to investigate the soot formation process in a diesel spray flame, simultaneous imaging of soot precursor and soot particles in a transient spray flame achieved in a rapid compression machine was conducted by laser-induced fluorescence (LIF) and by laser-induced incandescence (LII) techniques. The 3rd harmonic (355nm) and the fundamental (1064nm) laser pulses from an Nd:YAG laser, between which a delay of 44ns was imposed by 13.3m of optical path difference, were used to excite LIF from soot precursor and LII from soot particles in the spray flame. The LIF and the LII were separately imaged by two image-intensified CCD cameras with identical detection wavelength of 400nm and bandwidth of 80nm. The LIF from soot precursor was mainly located in the central region of the spray flame between 40 and 55mm (270 to 370 times nozzle orifice diameter d0) from the nozzle orifice. The LII from soot particles was observed to surround the soot precursor LIF region and to extend downstream.

Innovative Power Solutions (IPS), LLC has developed a 300A and a 500A 28 VDC Brushless Wound Rotor Starter/Generator (S/G) system. These systems are capable of replacing brush type S/G or Air Turbine Starters by presenting an adequate Torque vs. Speed performance. The S/G system developed by IPS consists of the Starter/Generator (Motor/Generator) and S/G Control Unit (SGCU).

The optimization of the vaporization and mixture formation process is of great importance for the development of modern gasoline direct injection (GDI) engines, because it influences the subsequent processes of the ignition, combustion and pollutant formation significantly. In consequence, the subject of this work was the development of a measurement technique based on the laser induced exciplex fluorescence (LIF), which allows the two dimensional visualization and quantification of the in-cylinder air/fuel ratio. A tracer concept consisting of benzene and triethylamine dissolved in a non-fluorescent base fuel has been used. The calibration of the equivalence ratio proportional LIF-signal was performed directly inside the engine, at a well known mixture composition, immediately before the direct injection measurements were started.

A historical review of the patents and literature pertaining to 3-valve stratified charge engines is presented in this paper. This very old invention appears to be a practical approach for the “clean engine” being sought for vehicular use since it has the intrinsic capability of simultaneously giving good fuel economy and producing minimal objectionable exhaust emissions. The prime requisites of this engine are a rich prechamber charge and a very lean main chamber charge regardless of prechamber volume, nozzle diameter, valving and spark plug location. Fuel-air equivalence ratios of the charges in the two combustion chambers are significantly important in order to achieve the proper optimization. These ratios should be about 15% rich for the prechamber and 15 to 30% lean for the main chamber at the moment of ignition.

A 3-D analysis of the flow through a multihole, V.C.O. (Valve Covered Orifice) nozzle for D.I. Diesel Engine has been carried out. The analysis was performed by means of a finite element code. The nozzle comprises five injection holes. Aims of the analysis were: the investigation of the pressure drops along the conical clearance between the needle and the nozzle; the evaluation of the energy losses in the injection holes; the disclosure of the velocity profile at the injection hole outlets. the differences of flowrate for each hole with geometrical asymmetries. This kind of analisys is the first step of a more complete spray analysis; in fact, the spray from an injection hole is influenced by the injection pressure and the velocity profile. In particular, the needle lift and the needle tip deviation have been parametrized. The analysis betters both the theoretical knowledge of this kind of nozzle and the hydraulic phenomena occurring inside.

The urea Selective Catalytic Reduction (SCR) exhaust system has been proved to be the reliable aftertreatment device with the capability of reducing tail pipe NOx emission by 75% to 90%, HC by 50% and Particulate Matter (PM) by 30%. Constrained by increasingly stringent packaging envelope, flow mixing in front of substrate is becoming one of the major concerns to achieve ideal performance of higher NOx conversion and lower ammonia (NH3) slip. Three dimensional CFD simulations are performed in current study to investigate flow mixing phenomenon in a SCR system. First, for a traditional tube injector with single or multiple nozzles, the effects of mass flow rates of injected NH3 and exhaust gas on flow mixing and pressure loss are investigated. Then, a concept of ring shape injector with multiple nozzles are initiated and built for 3-D CFD simulations. The comparisons of flow mixing index and injection pressure are made between two type injectors.

In this paper three-dimensional Large Eddy Simulations (i.e., LES) by using a PLIC-VOF method have been adopted to investigate the atomization process of round liquid jets issuing from automotive multi-hole injector-like nozzles. LES method is used to compute directly the effect of the large flow structure, being the smallest one modelled. A mesh having a cell size of 4 μm was used in order to derive a statistics of the detached liquid structures, i.e. droplets and ligaments. The latter have been identified by using an algorithm coded by authors. Cavitation modeling has not been included in the present computations. Two different mean injection nozzle flow velocities of 50 m/s and 270 m/s, corresponding to two mean nozzle flow Reynolds numbers of 1600 and 8700, respectively, have been considered in the calculations as representative of laminar and turbulent nozzle flow conditions.

The introduction of real driving emissions cycles and increasingly restrictive emissions regulations force the automotive industry to develop new and more efficient solutions for emission reductions. In particular, the cold start and catalyst heating conditions are crucial for modern cars because is when most of the emissions are produced. One interesting strategy to reduce the time required for catalyst heating is post-oxidation. It consists in operating the engine with a rich in-cylinder mixture and completing the oxidation of fuel inside the exhaust manifold. The result is an increase in temperature and enthalpy of the gases in the exhaust, therefore heating the three-way-catalyst. The following investigation focuses on the implementation of post-oxidation by means of scavenging in a four-cylinder, turbocharged, direct injection spark ignition engine. The investigation is based on detailed measurements that are carried out at the test-bench.

3M is committed to continuously improving products and their manufacture toward the goal of sustainability. The 3M Life Cycle Management (LCM) program has been established to implement this goal. It utilizes a matrix tool to facilitate the review. The matrix consists of LCM Stage (Material Acquisition, R&D Operations, Manufacturing Operations, and Customer Use/Disposal) and Impact (Environment, Health, Safety, and Energy/Resources). The program is coordinated at the staff level by the Corporate Product Responsibility group. The corporate goal is to apply LCM to all new and existing products. The LCM program started with evaluations of new products within business units. Since 3M produces more than 60,000 products manufactured from more than 10,000 different raw materials, the routine evaluation of individual products challenges available staff and business unit resources. A technology-based approach for doing LCMs has been implemented to meet the challenge.

Demands for new features, increasing electrical loads, and improved fuel-economy are driving development of 42V PowerNets in automobiles. Shorter design cycles, increased complexity and a focus on quality are making robust design processes a strategic advantage for competitive manufacturers. Hardware prototypes are both time-consuming and inadequate for the task of verifying performance over a broad range of operating modes, environmental conditions and part-to-part variations. This paper outlines the use of an advanced design-flow, from idea to manufacturing, for vehicle power systems. It starts with the analysis of different topologies down to the subsystem modeling of a power window system. Finally it integrates everything to a Digital Mock-Up (DMU) and analysis of the entire system. Dynamic interactions among the various supplies, converters and loads are examined. System stability and performance are assessed under normal and extreme operating conditions.

The increasing power demand in vehicles has resulted in a need for a higher onboard generation capacity. With the increasing generation requirement, the torque levels of the generator are found to closely converge with that of the starter motor. Hence, integrating the two machines and using a single machine for the two purposes would be technically viable and economically advantageous. This results in a more compact design solution as well. The Integrated Starter/Alternator (ISA) will be integrated directly to the crankshaft of the Internal Combustion Engine (ICE) and deliver 5 kW average and 12-15 kW peak power at 42V.

Crankshafts of motorcycles require high strength, high reliability and low manufacturing cost. Recently, a reduction of Pb content in the free-cutting steel, which is harmful substance, is required. In order to satisfy such requirements, we started the development of Pb-free free-cutting steel which simultaneously enabled the omission of the normalizing process. For the omission of normalizing process, we adjusted the content of Carbon, Manganese and Nitrogen of the steel. This developed steel can obtain adequate hardness and fine microstructure by air-cooling after forging. Pb-free free-cutting steel was developed based on Calcium-sulfur free-cutting steel. Pb free-cutting steel is excellent in cutting chips frangibility in lathe process. We thought that it was necessary that cutting chips frangibility of developed steel was equal to Pb free-cutting steel. It was found that cutting chips frangibility depend on a non-metallic inclusion's composition, shape and dispersion.

Diesel common rail injectors are required to utilize a higher injection pressure and to achieve higher injection accuracy in order to meet increasingly severe emissions, less fuel consumption, and higher engine performance demand. In addition to those requirements, in conjunction with optimized nozzle geometry, a more rectangular injection rate and stable multiple injections with shorter intervals are required for further emissions and engine performance improvement by optimizing the combustion efficiency.

The transition towards More Electric Aircraft (MEA) architectures has challenges relating to integration of power electronics with the starter generator system for on-engine application. To efficiently operate the power electronics in the hostile engine environment at high switching frequency and for better thermal management, use of silicon carbide (SiC) power devices for a bi-directional power converter is examined. In this paper, development of a 50 kVA bi-directional converter operating at an ambient temperature of about 2000C is presented. The design and operation of the converter with details of control algorithm implementation and cooling chamber design are also discussed.

The University of Liege and Breuer Technical Development, Belgium, have designed a parallel hybrid drive train, now implemented in a VW Lupo. The original objectives of the concept were the reduction of total CO2 emissions without performance loss and an acceptable zero-emission range for inner cities. This paper presents: Metropol, a homemade hybrid simulation software, including engine cold start and dynamic battery models, hybrid management strategy for the lowest CO2 emissions, final performance, consumption and emissions of the vehicle.

A flash evaporation model is being developed to capture the effects of bubble nucleation and growth inside multi-hole injector nozzles to investigate the flash evaporation in fuel injector sprays in Gasoline Direct Injection (GDI). The 1D flash evaporation model is a key tool for providing the 3D Eulerian-Eulerian or Lagrangian spray simulation model with the right droplet size in order to properly predict the effect of degree of superheating on mixture formation. Super heating conditions are likely to be found under partial load conditions in GDI applications or they might be deliberately induced to enhance fuel atomization and vaporization. A quasi-1D nozzle flow model has been developed to help quantifying the effects of main physical and geometrical parameters in promoting fuel flash evaporation. This model is based on an weakly compressible homogenous two-phase mixture assumption. A non-equilibrium model is used to predict the vapour formation rate along the nozzle.

This paper provides an overview of a strategy for the prediction of noise from industrial gearboxes. A review of the history of predictive noise control in gearboxes is given. The historical lead is followed in developing the strategy, but significant changes in the approach to predictive noise control have been made. The heart of the approach is the dynamic modeling of the gearbox from inside out. Thus one must start this process with the prediction of the internal dynamic response of the gear train system. This paper then details the computational strategy for the determination of the dynamic response of the internal gearbox components. The approaches presented here are significant departures from those carried out in the past.

The 14/42V Electrical System Architectures have been the subject of discussions in many technical meetings. Some of the major challenges are: system cost, mixed load handling flexibility, jump start issue, battery service life, and transient voltage under load dump situation. In this paper, a patented, bi-directional, charge-transfer circuit is evaluated against these criteria. Circuit performance is discussed in details. It covers circuit efficiency, battery voltage ripple, and transfer-current ripple, and the effectiveness of balancing the battery voltages under various mixed 12/36V loads. The energy transfer principle between a 14V system and a 42V system is presented to demonstrate the cross jumping and surge-load handling capability. The bi-directional energy transfer capability of the circuit easily keeps the load-dump transient-voltage under the 58V limit with either the 14V or the 28V batteries are disconnected.