Search Results

Accurate ride and handling prediction is an important requirement in today's automobile industry. To achieve the same, it is imperative to have a good estimation of damper model. Conventional methods used for modelling complex vehicle components (like bushings and dampers) are often inadequate to represent behaviour over wide frequency ranges and/or different amplitudes. This is difficult in the part of OEMs to model the physics-based model as the damper’s geometry, material and characteristics property is proprietary to part manufacturer. This is also usually difficult to obtain as a typical data acquisition exercise takes lots of time, cost, and effort. This paper aims to address this problem by predicting the damper force accurately at different velocity/ frequency and amplitude of measured data using Artificial Neural Networks (ANN).

Ride comfort, drivability and driving stability are important factors defining vehicle performance and customer satisfaction. The IC powertrain is the source for the vibration that adversely affects the vehicle performance. The IC powertrain is composed of reciprocating and rotating components which result in unbalanced forces, moments during operation and produce vibrations at the vehicle supporting members. The vibration reduction is possible by minimizing unbalanced forces and/or by providing anti-vibration mounts at the powertrain-vehicle interface. The power train is suspended on the vehicle frame via several flexible mounts, whose function is to isolate powertrain vibrations from the frame. Total six different modes of powertrain vibration namely - roll, yaw, pitch, vertical, lateral and longitudinal need to be isolated. Powertrain mount stiffness and location is critical in this regard.

In driving, Steering is the input motion to the vehicle. The driver uses steering input to change the direction of the vehicle. During Parking or U turn bends the Steering is locked and later released to follow the desired path. Steering return ability is defined as the ratio of difference between steering wheel position at lock condition and steering wheel angle after 3 seconds of release to the steering wheel angle at lock condition. Having proper steering return ability characteristics has an important effect on vehicle steering characteristics. In this study, a full vehicle ADAMS model is prepared, and virtual steering return ability have been simulated in ADAMS/CAR for a Pickup truck vehicle. Simulated responses in the steering wheel angle have been validated by comparison with measurements. A Design of Experiment study is setup and Iterations are carried out to find the effect of Hard points and friction parameters.

In India, demand for motorcycle with good comfort is increasing among the customers thereby the vibration reduction of two wheelers is key parameter for motorcycle manufacturers. In order to overcome the demand in the market, manufacturers are giving more importance to cost of the product by reducing the material. This results in the reduction of the life cycle of the vehicle models and drives the manufacturers to different product design philosophies and design tools, as one would expect. One of the performance factors that continue to challenge designers is that of vehicle vertical acceleration experienced by the motorcycle components. An essential tool in the motorcycle development process is the ability to quantify the durability of the component. This paper main objective is to increase the life of the motorcycle front fender through virtual simulation, on road testing and laboratory testing using NVH tool.

The main challenge that arises in the design of a motorcycle frame is its effect on the functionality on the vehicle, its effect on ride comfort and its durability. While functionality and ride comfort due to frame can be evaluated by subjectively testing it before the product reaches customer, evaluation of its durability is a complex process. This work is an investigation of the frame body of a 100 cc vehicle in India. These vehicles are subjected to endurance tests on a rough road at vehicle level to quantitatively evaluate their frame durability. However, such tests require significant time and cost, so an attempt has been made to develop a virtual rough road simulator to extract forces involved in it and testing the frame at component level with those loads on a test rig. Also durability results were compared and analyzed with the track data and frame test rig.

A critical requirement for product design and development is meeting vehicle dynamic performance. Customers changing needs puts tremendous pressure on automotive businesses to launch new vehicles within short durations of time. This makes it mandatory to have a wide-ranging virtual simulation and vigorous validation process to provide best in class ride and handling performance of vehicles. Physical testing of prototypes is the most time-consuming activity, so there is a need of front loading to substitute these requirements at the initial stage of the development cycle. This paper summarizes the overall process for front loading vehicle dynamics requirements during basic architecture definition using virtual simulation. Basic dimensions, CG, weight distribution and steer angle of the new vehicle are derived using concept calculations based on benchmark vehicles. Vehicle dynamics trials are then done for the benchmark vehicles.

A vehicle drifts due to several reasons from its intended straight path even in the case of no steering input. Vehicle pull is a condition where the driver must apply a constant correction torque to the steering wheel to maintain a straight-line course of the vehicle. This paper presents an investigation study into the characteristics of a vehicle experiencing steering drift. The aim of the work is to study vehicle stability and the causes of vehicle drift/pull during straight line to minimize vehicle pull level and hence optimize safety measures. A wobble in the steering wheel feels like the steering wheel is shaking to the left and right. This may get worse, if speed increases. This paper focuses on modelling and evaluating effects of suspension parameters, differential friction, brake drag variation, Unbalanced mass in the wheel assembly and C.G. location of the vehicle under multibody dynamic simulation environment.

Lateral Stability is an important attribute which must be accounted for in the pick-up truck segment vehicles. If designed in an improper way, undesirable effects such as oversteer or tail sway may occur. Excessive yaw rate magnitudes, or tail sway, can reduce the confidence of the driver during severe lane change events. The concept architecture of the vehicle plays an important role in how stable the vehicle will be. High yaw rate or tail sway during limit cornering was reported during prototype vehicle evaluations. The tested vehicle configuration incorporated a double wish bone front suspension with an antiroll bar and a rear solid axle suspension with leaf springs and an antiroll bar. The feedback was critically analysed using computer simulations of the condition found in on track testing. Since the vehicle was still with the validation team, quick solution was necessary. This paper discusses the process which resulted in improved vehicle performance.

Ride is an important attribute which must be accounted in the passenger segment vehicles. Excessive H point acceleration, Steering wheel acceleration, Pitch acceleration can reduce the comfort of the driver and the passengers during high frequency and low frequency rough road events. Excessive Understeer gradient, roll gradient, roll acceleration and Sprung mass lift could affect the Vehicle driver interaction during Steady state cornering, Braking and Step steer events. The concept architecture of the vehicle plays an important role in how comfort the vehicle will be. This paper discusses how to improve SUV ride performances by keeping handling performance attributes same or better than base vehicle. Multi Objective Optimization was carried out by keeping spring, bushing and damper characteristic as the design variables to avoid new system or component development time and cost.

In the automobile industry, the door closing effort spells out the engineering and quality of the vehicle. After the visual impact a vehicle has on the customer, the doors are most likely the very first part of the vehicle he/she encounters, to enter and exit the vehicle. One of the customer’s very first impressions about the quality of the car is given by the behavior of the doors when opening and closing, the swinging velocity and the energy that is required to obtain a full latching that the door makes when closed by the user. Door closing effort gives an indication of how good or bad the vehicle is engineered. The purpose of this paper is to propose modifications in the door system which help in reduction of door closing effort or velocity by two different methods, EZ Slam Door and Bungee Rope. In this paper, parameters like hinge friction, hinge axis inclination, sealing, latch and air bind effect are analyzed which affect door closing effort.

Costlier engine exhaust gas treatment systems as a result of stringent emission norms and increasing awareness about industrial effects on climate have pushed the automotive industry around the globe to shift its focus from fossil fuel driven vehicles to electrically powered ones. While Battery Electric Vehicles (BEVs) have some problematic issues such as lower range, lesser energy density and higher cost owing to not fully mature battery technology, they do provide some benefits such as lower carbon footprint and simpler transmission systems. The torque and power characteristics vary greatly between IC engines and electric motors. The longitudinal dynamics of a vehicle depends greatly on the nature of its powertrain. As a result, new challenges have emerged for simulation engineers who were until very recently accustomed only to IC engine driven vehicles.

Structural elastomer components like bushes, engine mounts are required to meet stringent and contrasting requirements of being soft for better NVH and also be durable at different loading conditions and different road conditions. Silent block bushes are such components where the loading in radial direction of bushes are high to ensure the durability of bushes at high loads, but has to be soft on torsion to ensure good NVH. These requirements present with unique challenge to optimize the leaf spring bush design, stiffness and material characteristics of the rubber. Traditionally, bushes with varying degree of stiffness are selected, manufactured and tested on vehicle and the best one is chosen depending on the requirements. However, this approach is costly, time consuming and iterative. In this study, the stiffness targets required for the bush were analysed using static and dynamic load cases using virtual simulation (MSC.ADAMS).

Today’s automotive industry is a highly competitive market where continuous innovation in design and production of vehicles is required to gain market share and survive in the market. This led to reduction in the life cycle of the design process and design tools. Identifying, understanding and refining these details is significant to develop sustainable cars. Body and chassis stiffness are important specifications of a passenger car which affects handling, steering and ride characteristics of the vehicle. It has been proved that torsional, lateral and local chassis stiffness can play a role in giving the customer a premium feeling by affecting key metrics in the vehicle dynamics behaviour of a passenger car. In this paper, the effect of chassis stiffness on vehicle dynamics performance is studied using computer aided engineering (CAE). Different attributes of vehicle dynamics like vehicle handling, On-Center feel and vehicle ride are considered as performance characteristics.

Hardware-in-the-loop (HIL) test benches are indispensable for the development of modern vehicle dynamics controllers (VDCs). They can be regarded as a standard methodology today, because of the extremely safety critical nature of the multi-sensor and multi-actuator systems used in vehicle dynamics control. The required high quality standards can only be ensured by systematic testing within a virtual HIL environment before going into a real car. The steering system is an important aspect of the automobile from operational safety and driver enjoyment perspectives. Current Problem/Opportunity is realistic subjective steering feel prediction before vehicle build. And upfront predict the handling characteristics more accurately with subjective feel before proto build. Current Issue is difficult to convert the objective data into subjective feel and difficult to incorporate the nonlinear steering characteristics with hysterics, friction and power assist curves using virtual simulation.

Automotive industry has led to constant production innovation among manufactures. This has resulted in the reduction of the life cycle of the design philosophies and design tools. One of the performance factors that have continues to challenge automotive designer is to design and fine tune the braking performance with low cost and short life cycle. Improvement in braking performance and vehicle stability can be achieved through the use of braking systems whosebrake force distribution is variable. Braking force distribution has an important and serious role in thevehicle stopping distance and stability. In this paper a new approach will be presented to achieve the braking forcedistribution strategy for articulated vehicles. For this purpose, the virtual optimization process has beenimplemented.

Fierce competition in India’s automotive industry has led to constant production innovation among manufactures. This has resulted in the reduction of the life cycle of the design philosophies and design tools. One of the performance factors that have continues to challenge automotive designer is to design and fine tune the braking performance with low cost and short life cycle. Braking performance of automotive vehicle is facilitated by the adhesion between the tyre and the ground. Braking force generated at the wheels of a vehicle have to appropriately match to the adhesion. Antilock braking system (ABS) is used for this purpose. ABS is a modern braking system which could significantly improve directional stability and reduce stopping distance of a vehicle. However this system still too complicated and expensive to use in low end compact car and pickup truck.