Search Results

An experimental study of the Homogeneous Charge Compression Ignition (HCCI) combustion process has been conducted by using chemiluminescence imaging. The major intent was to characterize the flame structure and its transient behavior. To achieve this, time resolved images of the naturally emitted light were taken. Emitted light was studied by recording its spectral content and applying different filters to isolate species like OH and CH. Imaging was enabled by a truck-sized engine modified for optical access. An intensified digital camera was used for the imaging. Some imaging was done using a streak-camera, capable of taking eight arbitrarily spaced pictures during a single cycle, thus visualizing the progress of the combustion process. All imaging was done with similar operating conditions and a mixture of n-heptane and iso-octane was used as fuel. Some 20 crank angles before Top Dead Center (TDC), cool flames were found to exist.

This paper illustrates the applicability of a sequential fluid mechanics, multi-zone chemical kinetics model to analyze HCCI experimental data for two combustion chamber geometries with different levels of turbulence: a low turbulence disc geometry (flat top piston), and a high turbulence square geometry (piston with a square bowl). The model uses a fluid mechanics code to determine temperature histories in the engine as a function of crank angle. These temperature histories are then fed into a chemical kinetic solver, which determines combustion characteristics for a relatively small number of zones (40). The model makes the assumption that there is no direct linking between turbulence and combustion. The multi-zone model yields good results for both the disc and the square geometries. The model makes good predictions of pressure traces and heat release rates.

The potential of a Homogeneous Charge Compression Ignition (HCCI) engine with variable compression ratio has been experimentally investigated. The experiments were carried out in a single cylinder engine, equipped with a modified cylinder head. Altering the position of a secondary piston in the cylinder head enabled a change of the compression ratio. The secondary piston was controlled by a hydraulic system, which was operated from the control room. Dual port injection systems were used, which made it possible to change the ratio of two different fuels with the engine running. By mixing iso-octane with octane number 100 and normal heptane with octane number 0, it was possible to obtain any octane rating between 0 and 100. By using an electrical heater for the inlet air, it was possible to adjust the inlet air temperature to a selected value.

Natural gas quality, in terms of the volume fraction of higher hydrocarbons, strongly affects the auto-ignition characteristics of the air-fuel mixture, the engine performance and its controllability. The influence of natural gas composition on engine operation has been investigated both experimentally and through chemical kinetic based cycle simulation. A range of two component gas mixtures has been tested with methane as the base fuel. The equivalence ratio (0.3), the compression ratio (19.8), and the engine speed (1000 rpm) were held constant in order to isolate the impact of fuel autoignition chemistry. For each fuel mixture, the start of combustion was phased near top dead center (TDC) and then the inlet mixture temperature was reduced. These experimental results have been utilized as a source of data for the validation of a chemical kinetic based full-cycle simulation.

The Homogeneous Charge Compression Ignition (HCCI) is the third alternative for combustion in the Internal Combustion (IC) engines. Here, a homogeneous charge is used as in a spark ignited engine but the charge is compressed to auto-ignition as in a diesel. The characteristics of HCCI were compared to SI using a 1.6 liter single cylinder engine with compression ratio 21:1 in HCCI mode and 12:1 in SI mode. Three different fuels were used; isooctane, ethanol and natural gas. Some remarkable results were noted in the experiments: The indicated efficiency of HCCI was much better than for SI operation. Very little NOx was generated with HCCI, eliminating the need for a LeanNOx catalyst. However, HCCI generated more HC and CO than SI operation. Stable and efficient operation with HCCI could be obtained with λ=3 to λ=9 using isooctane or ethanol. Natural gas, with a higher octane number, required a richer mixture to run in HCCI mode.

One way to extend the lean burn limit of a natural gas engine is by addition of hydrogen to the primary fuel. This paper presents measurements made on a one cylinder 1.6 liter natural gas engine. Two combustion chambers, one slow and one fast burning, were tested with various amounts of hydrogen (0, 5, 10 and 15 %-vol) added to natural gas. Three operating points were investigated for each combustion chamber and each hydrogen content level; idle, part load (5 bar IMEP) and 13 bar IMEP (simulated turbocharging). Air/fuel ratio was varied between stoichiometric and the lean limit. For each operating point, a range of ignition timings were tested to find maximum brake torque (MBT) and/or knock. Heat-release rate calculations were made in order to assess the influence of hydrogen addition on burn rate. Addition of hydrogen showed an increase in burn rate for both combustion chambers, resulting in more stable combustion close to the lean limit.

This work has focused on studying the in-cylinder pressure fluctuations caused by rapid HCCI combustion and determine what they consist of. Inhomogeneous autoignition sets up pressure waves traversing the combustion chamber. These pressure waves induce high gas velocities which causes increased heat transfer to the walls or in worst case engine damage. In order to study the pressure fluctuations a number of pressure transducers were mounted in the combustion chamber. The multi transducer arrangement was such that six transducers were placed circumferentially, one placed near the centre and one at a slight offset in the combustion chamber. The fitting of six transducers circumferentially was enabled by a spacer design and the two top mounted transducers were fitted in a modified cylinder head. During testing a disc shaped combustion chamber was used. The results of the tests conducted were that the in-cylinder pressure experienced during rapid HCCI-combustion is inhomogeneous.

In an attempt to extend the upper load limit for Homogeneous Charge Compression Ignition (HCCI), supercharging in combination with Exhaust Gas Recirculation (EGR) have been applied. Two different boost pressures were used, 1.1 bar and 1.5 bar. High EGR rates were used in order to reduce the combustion rate. The highest obtained IMEP was 16 bar. This was achieved with the higher boost pressure, at close to stoichiometric conditions and with approximately 50 % EGR. Natural gas was used as the main fuel. In the case with the higher boost pressure, iso-octane was used as pilot fuel, to improve the ignition properties of the mixture. This made it possible to use a lower compression ratio and thereby reducing the maximum cylinder pressure. The tests were performed on a single cylinder engine operated at low speed (1000 rpm). The test engine was equipped with a modified cylinder head, having a Variable Compression Ratio (VCR) mechanism.

An experimental and theoretical study of the effect of thermal barriers and catalytic coatings in a Homogeneous Charge Compression Ignition (HCCI) engine has been conducted. The main intent of the study was to investigate if a thermal barrier or catalytic coating of the wall would support the oxidation of the near-wall unburned hydrocarbons. In addition, the effect of these coatings on thermal efficiency due to changed heat transfer characteristics was investigated. The experimental setup was based on a partially coated combustion chamber. The upper part of the cylinder liner, the piston top including the top land, the valves and the cylinder head were all coated. As a thermal barrier, a coating based on plasma-sprayed Al2O3 was used. The catalytic coating was based on plasma-sprayed ZrO2 doped with Platinum. The two coatings tested were of varying thickness' of 0.15, 0.25 and 0.6 mm. The compression ratio was set to 16.75:1.

The effect of the combustion chamber geometry and the turbulence on Homogeneous Charge Compression Ignition (HCCI) operation has been experimentally investigated. A high turbulent square bowl in piston combustion chamber has been compared with a low turbulent disc combustion chamber. The results showed that the combustion chamber geometry plays large role for HCCI combustion. At the same operating conditions, the peak combustion rate for the square bowl combustion chamber was much lower compared to the disc combustion chamber. The combustion duration was in some cases almost a factor two longer for the square bowl combustion chamber. The lower combustion rate with the square bowl was due larger heat losses, lower combustion efficiency and higher turbulence.

The effect of in-cylinder flow and turbulence on HCCI operation has been experimentally studied by changing the combustion chamber geometry and the swirl ratio. Four different levels of turbulence were achieved, by altering the swirl ratio both for a high turbulent square bowl-in-piston combustion chamber and for a low turbulent disc combustion chamber. The swirl ratio was altered by using different inlet port designs. The results showed that the combustion chamber geometry plays a large role in HCCI combustion. With the same operating conditions, the combustion duration for the square bowl-in-piston combustion chamber was much longer compared to the disc combustion chamber. On the other hand, a moderate change in swirl ratio proved to have only modest effect on the combustion process. With early combustion timing, the gross indicated efficiency was higher when the square bowl-in-piston combustion chamber.

The effect of crevice volumes on the emissions of unburned hydrocarbons from a Homogeneous Charge Compression Ignition (HCCI) engine has been experimentally investigated. By varying the size and the geometry of the largest crevice, the piston topland, it was possible to ascertain whether or not crevices are the largest source of HC. Additionally, information on quenching distances for ultra lean mixtures was obtained. The tests were performed on a single cylinder engine fuelled with iso-octane. The results showed that most of the unburned hydrocarbons descend from the crevices. Increasing the topland width to some degree lead to an increase in HC. A further increase in topland width (>1.3 mm) resulted in a reduction of HC when using mixtures richer than λ ≈ 2.8, indicating that some of the mixture trapped in the topland participates in the combustion. In conditions when combustion occurred in the topland, the HC was rather insensitive to the height of the topland.