Search Results

This paper presents the rationale behind the development of a shoulder belt load cell suitable for application in racings cars. The design of the load cell and the operational parameters necessary for a research-quality measurement device for biomechanics research in racing car crashes and the performance of the device in sled tests are described.

This paper summarizes the results of Phase 1, Concept Definition, of the AATD program and identifies the reasons such a new test device is needed. The following areas are addressed: 1) injury priority from accident data; 2) current dummy design, use, and potential improvements; and 3) technical characteristics and design concepts for a new AATD, its data processing, and its certification systems.

The purpose of this literature review was to determine areas of automotive injury information that may add to knowledge of injury type, frequency, severity, and cause. This paper is a review of the literature concentrating on the period between 1965 and present. Literature on car, van, or 1ight truck occupants has been reviewed for injury frequencies, types, and locations. Current experimental biomechanical articles are also included. A search was made for descriptions of injury frequency, restraint effectiveness, and the causes of specific injuries. Medical and engineering journals, texts, and books were reviewed. For convenience, this report is divided into sections by body region with an overview introduction on the anatomy of the specific region.

The crash recorder is an important data gathering device in motorsports. Since the introduction of crash recording in Indy Cars in 1993, the data gathered has been critical in developing improvements in race car structures and driver protection systems. This report will examine which sanctioning bodies use recorders, what type of data is gathered, and how that data is used to improve driver's safety in racing.

This study examines the static pressure distribution under both width belts in the shoulder and the pelvis of 15 volunteer subjects. The subjects applied the belt loads to themselves through a lever and pulley system. The configuration of the belts simulated the typical arrangement of a six-point belted upright-seated racing driver. The pressure distribution between the belt and the volunteer's body was determined and recorded with Tek-Scan pressure sensing grids. The paper presents the results of the measurements by comparing the actual area of significant loading beneath the two widths and materials of both lap and shoulder belts. In, general, there no significant increase in loaded area for the wider belts.

The results of recent dynamic load measurements on human skull and patella bone, conducted with less-than-1-sq-in. penetrators, are discussed in relation to previously reported skull impact data from larger contact areas. These medical data are compared to the dynamic response of a large variety of natural and synthetic plastic materials, for use in trauma-indicating headform and kneeform design. Several bodyform designs are proposed as research tools.

Multiple axial knee impacts and/or a single lateral pelvis impact were performed on a total of 19 cadavers. The impacting surface was padded with various materials to produce different force-time and load distribution characteristics. Impact load and skeletal acceleration data are presented as functions of both time and frequency in the form of mechanical impedance. Injury descriptions based on gross autopsy are given. The kinematic response of the pelvis during and after impact is presented to indicate the similarities and differences in response of the pelvis for various load levels. While the impact response data cannot prescribe a specific tolerance level for the pelvis, they do indicate variables which must be considered and some potential problems in developing an accurate injury criterion.

This paper is a brief review of the complex subject of human injury mechanisms and impact tolerance. Automotive accident-related injury patterns are briefly described and the status of knowledge in the biomechanics of trauma of the head, neck, chest, abdomen and extremities is discussed.

The technical and scientific literature dealing with thoracic injury, to or within the rib cage, from blunt loading is reviewed. The history of the development of associated Federal Motor Vehicle Safety Standards is reviewed from the aspect of its relationship to the history of development of the research information. Field case data from car-to-car and car-to-tree/pole crashes has been examined and summarized. This study suggests that the laboratory research has not adequately covered the principal variables found to exist in actual injury cases. Specifically, more research attention should be given to the shape of the impactor, to the loading location and direction, and to injuries in the contusion and/or laceration family. Correspondingly, the accident investigation process needs to be more sensitive to occupant/vehicle-interior interaction variables so that laboratory research can be properly guided.

Over the last decade large safety improvements have been made in crash protection for stock car racing drivers. It has been well established that in side and rear impacts the driver seat provides the primary source for occupant retention and restraint. With the implementation of NASCAR®'s (National Association for Stock Car Auto Racing, Inc) newest generation of stock car, the Car of Tomorrow (COT), into the racing schedule, the opportunity to develop and implement a universal stock car driver seat performance specification was accomplished. This paper describes the development of the Seat Performance Specification including the goals of the specification, the methodology used to develop it, a census of the existing driver seat population used in on-track competition, review of developmental dynamic specification sled tests and quasi-static tests as well as summation of the Seat Performance Specification requirements.

A test series using unembalmed cadavers was conducted to investigate thoracic response differences in lateral impacts between high energy (rib fractures produced) and low energy (no rib fractures produced) testing and also the response to low energy impacts for different impact directions (frontal, 45°, and lateral). Five of the test subjects were instrumented with a nine-accelerometer package and an eighteen-accelerometer array to measure thoracic response. Seven of the test subjects were instrumented with a triaxial accelerometer on the head and a six-accelerometer array to measure thoracic response. Impact events were performed with either the UMTRI pendulum impact device or the UMTRI pneumatic impact device. The subject was struck with a free-traveling mass (25 or 56 kg) which was fitted with either a 15 cm round or 20 cm square rigid metal surface.