Search Results

The regulatory requirements to reduce both greenhouse gases and exhaust gas pollutants from heavy duty engines are driving new perspectives on the interaction between fuels and engines. Fuels that reliefs the burden on engine manufacturers to reach these goals are of particular interest. A low carbon fuel with a higher volatility and heating value than diesel is one such fuel that reduces engine-out emissions and carbon footprint from the entire hydrocarbon lifecycle (well-to-wheel) and improves fuel efficiency, which is a main enabler for gasoline compression ignition (GCI) technology. The present study investigated the potential of GCI technology by evaluating the performance of a low carbon high efficiency, high reactivity gasoline fuel in Doosan’s 6L medium duty diesel engine.

The autoignition resistance of a practical gasoline is best characterized by the Octane Index, OI, defined as RON-KS, where RON and MON are respectively, Research and Motor Octane Numbers, S is the sensitivity (RON-MON) and K is a constant depending on the pressure and temperature history of the fuel/air mixture in an engine. Experiments in knocking SI engines, HCCI engines and in premixed compression ignition (PCI) engines have shown that if two fuels of different composition have the same OI and experience the same pressure/temperature history, they will have the same autoignition phasing. A practical gasoline is a complex mixture of hydrocarbons and a simple surrogate is needed to describe its autoignition chemistry. A mixture of toluene and PRF (iso-octane + n-heptane), TPRF, can have the same RON and S as a target gasoline and so will have the same OI at any given K value and will be a very good surrogate for the gasoline.

In a regulatory environment for spark ignition (SI) engines where the focus is continuously looking into improvements in fuel economy and reduction in noxious emissions, the challenges to achieve future requirements are utmost. To effectively reduce CO2 emissions on a well-to-wheel basis, future fuels enabling high efficiency SI engines will have to not only satisfy advanced engine requirements, i.e. high knock resistance, but also produce less CO2 emissions in the refinery. This paper describes how to characterize SI combustion's on-demand octane requirement with three different dual fuel configurations. Refinery naphtha was used for low octane component, and three oxygenates were used for high octane knock inhibiting component, such as, Methanol and Methyl tert-butyl ether (MTBE) and Ethyl tert-butyl ether (ETBE). Each low and high octane fuel was introduced via production gasoline direct injector (DI) and port fuel injector (PFI) in both configurations.

In the context of stringent future emission standards as well as the need to reduce emissions of CO2 on a global scale, the cost of manufacturing engines is increasing. Naphtha has been shown to have beneficial properties for its use as a fuel in the transportation sector. Well to tank CO2 emissions from the production of Naphtha are lower than any other fuel produced in the refinery due to its lower processing requisites. Moreover, under current technology trends the demand for diesel is expected to increase leading to a possible surplus of light fuels in the future. Recent research has demonstrated that significant fuel consumption reduction is possible based on a direct injection gasoline engine system, when a low quality gasoline stream such as Naphtha is used in compression ignition mode. With this fuel, the engine will be at least as efficient and clean as current diesel engines but will be more cost effective (lower injection pressure, HC/CO after-treatment rather than NOx).

The present investigation pertains to the development of fast idle catalyst light-off strategy for a light duty gasoline compression ignition (GCI) engine. The engine cold start fast idle operation poses a problem of increased criteria emissions if the catalyst is not activated during the warm up period. Therefore, a control strategy is proposed here to minimize the criteria pollutants during the fast idle phase via enabling fast catalyst light off in a GCI engine and relying on the spark ignition of a globally stoichiometric fuel air mixture. The engine has unique design features such as certain geometry configuration between spark plug and fuel injector arrangement, and the location of spark plug in a high compression ratio (CR) diesel-like combustion chamber. The experiments were performed in a single cylinder GCI engine at cold start fast idle conditions using certification gasoline fuel (RON 91).

The present investigation expands on our previous work on development of fast idle catalyst light-off strategy for a light duty gasoline compression ignition (GCI) engine. In part 1, the steady state experimental investigation in a single cylinder GCI engine indicate an optimum strategy for effective catalyst light off during cold start fast idle operation. According to this strategy, the strategy includes (1) dispersing a first fuel injection during the intake stroke, (2) dispersing a second fuel injection during the expansion stroke, and (3) igniting a spark during the expansion stroke. This strategy increases the exhaust temperature during cold starts thereby assisting in lighting the oxidation catalyst, and reduce emissions and provide greater combustion stability as compared to other injection and spark strategies.

Gasoline compression ignition (GCI) engines have been considered an attractive alternative to traditional spark ignition engines. Low octane gasoline fuel has been identified as a viable option for the GCI engine applications due to its longer ignition delay characteristics compared to diesel and in the volatility range of gasoline fuels. In this study, we have investigated the effect of different injection timings at part-load conditions using light naphtha stream in single cylinder engine experiments in the GCI combustion mode with injection pressure of 130 bar. A toluene primary reference fuel (TPRF) was used as a surrogate for the light naphtha in the engine simulations performed here. A physical surrogate based on the evaporation characteristics of the light naphtha has been developed and its properties have been implemented in the engine simulations.

More stringent emissions standards along with higher fuel economy demands have obliged auto makers to develop technical solutions that exploit synergistic features from gasoline and diesel engines. To minimize NOx and soot trade-off, diesel powertrain has been developed to adopt increasingly complex and expensive technology such as extremely high pressure fuel injection systems, low pressure EGR, and variable valve timing. These attempts are associated with promoting Partially Premixed Charge Compression Ignition (PPC-CI) combustion via increasing mixing time and ignition delay. Alternatively, PPC-CI combustion can be achieved easier by using fuels with higher resistance to auto-ignition than conventional diesel fuel. Previous work has demonstrated the possibility of reducing the cost of future diesel after-treatment systems by using gasoline-like fuels.

Recent research [21] has shown that the compression ignition concept where very low cetane fuels (RON between 70 and 85) are run in compression ignition (CI) mode has several advantages. The engine will be at least as efficient and clean as the current diesel engines but will have a less complicated after-treatment system. The optimum fuel will be less processed and therefore simpler to make compared to current gasoline or diesel fuels. Naphtha, which is a product of the initial distillation of petroleum, is one such fuel. It provides a path to mitigate the global demand imbalance between heavier and lighter fuels that is otherwise projected. Since naphtha requires much less processing in the refinery than either gasoline or diesel [23], there is an additional benefit in terms of well-to-wheel CO2 emissions and overall energy consumed. Partially premixed charge compression ignition combustion with such a low cetane fuel has usually been investigated with a diesel engine base.

This paper is the second of a two part study which investigates the use of advanced combustion modes as a means of improving the efficiency and environmental impact of conventional light-duty vehicles. This second study focuses on drive cycle simulations and Life Cycle Assessment (LCA) for vehicles equipped with Octane-on-Demand combustion. Methanol is utilized as the high octane fuel, while three alternative petroleum-derived fuels with Research octane numbers (RONs) ranging from 61 to 90 are examined as candidates for the lower octane fuel. The experimental engine calibration maps developed in the previous study are first provided as inputs to a drive cycle simulation tool. This is used to quantify the total fuel consumption, octane requirement and tank-to-wheel CO2 emissions for a light-duty vehicle equipped with two alternative powertrain configurations. The properties of the lower octane fuel are shown to affect the vehicle fuel consumption and CO2 emissions significantly.

The pre-chamber combustion can extend the lean limit of internal combustion engines (ICE) and hence increase their overall efficiency. Compared to active pre-chambers equipped with an auxiliary fuel supply system, passive pre-chambers have lower manufacturing costs and require minimal or no design modifications to the conventional spark plug engines. The major challenge of the passive pre-chamber is to extend the lean limit as much as the active pre-chamber. Computational fluid dynamics (CFD) simulations were conducted on a light-duty single-cylinder engine geometry fitted with a passive pre-chamber and using iso-octane as fuel to investigate and optimize the passive pre-chamber fuel enrichment through the pre-chamber nozzles. The non-reacting flow simulations were performed from the intake valve open (IVO) to spark timing.

This paper explores the potential for reducing transport-related greenhouse gas (GHG) emissions by introducing high-efficiency spark-ignition engines with a dual-fuel injection system to customize the octane of the fuels based on real-time engine requirements. It is assumed that a vehicle was equipped with two fuel tanks and two injection systems; one port fuel injection and one direct injection line separately. Each tank carried low octane and high octane fuel so that real-time octane blending was occurred in the combustion chamber when needed (Octane On-Demand: OOD). A refinery naphtha was selected for low octane fuel (RON=61), because of its similarity to gasoline properties but a less processed, easier to produce without changing a refinery configuration. Three oxygenates were used for high octane knock-resistant fuels in a direct injection line: methanol, MTBE, and ETBE.

Gasoline compression ignition (GCI) pertains to high efficiency lean burn compression ignition with gasoline fuels, where ignition is controlled by mixture’s auto-ignition chemistry as well as local mixture strength. The presented GCI combustion strategy is based on a multi-mode combustion strategy at various operating conditions. This study presents a part of work on the development of an optimum combustion strategy at medium loading condition for commercial gasoline fuel with research octane number (RON) = 91. The single cylinder engine with a compression ratio (CR) = 16 features a centrally mounted multi-hole injector with a spark plug at a distance from the injector under shallow pent-roof combustion chamber design. The design of combustion chamber and piston was previously optimized based on CFD numerical analysis.