Search Results

The challenge posed by the long run times necessary to accurately quantify ash effects on diesel aftertreatment systems has led to numerous efforts to artificially accelerate ash loading, with varying degrees of success. In this study, a heavy-duty diesel engine was outfitted with a specially designed rapid lubricant degradation and aftertreatment ash loading system. Unlike previous attempts, the proposed methodology utilizes a series of thermal reactors and combustors to simulate all three major oil consumption mechanisms, namely combustion in the power cylinder, evaporative and volatile losses, and liquid losses through the valve and turbocharger seals. In order to simulate these processes, each thermal reactor allows for the precise control of the level of lubricant additive degradation, as well as the form and quantity of degradation products introduced into the exhaust upstream of the aftertreatment system.

Difficulties in the starting and operation of diesel engines at low temperatures are an important consideration in their design and operation, and in selection of the fuels for their use. Improvements in operation have been achieved primarily through external components of the engine and associated subsystems. A Rapid Compression Machine (RCM) has been modified to operate over a wide range of temperatures (−20°C to 100°C). It is used to isolate the combustion chamber in an environment in which all significant parameters are carefully defined and monitored. The influence of temperature and cetane number on the ignition and combustion processes are analyzed. Examination of the combustion characteristics show that temperature is by far the most influential factor affecting both ignition delay and heat release profiles. Cetane number (ASTM D-613) is not found to be a strong indicator of ignition delay for the conditions investigated.

A dry piston secondary dynamics model has been developed. This model includes the detailed piston and cylinder bore hot shape geometries, and piston deformations due to combustion pressure, axial inertia and interaction with the cylinder bore, but neglects the effects of the hydrodynamic lubrication at the piston - cylinder bore interface in order to achieve faster calculation times. The piston - cylinder bore friction is calculated using a user supplied friction coefficient. This model provides a very useful, fast tool for power cylinder system analysis, provided its limitations are understood.

Faced with increasing concern for lubricating oil consumption and engine friction, it is critical to understand the oil transport mechanisms in the power cylinder system. Lubricating oil travels through distinct regions along the piston ring pack before being consumed in the combustion chamber, with the oil distribution and dominant driving forces varying substantially for each of these regions. In this work, the focus is on the lowest region in the piston ring pack, namely the third land, which is located between the second compression ring and the oil control ring. A detailed 2D LIF (Two Dimensional Laser Induced Fluorescence) study has been performed on the oil distribution and flow patterns of the third land throughout the entire cycle of a single cylinder spark ignition engine. The impact of speed and load were experimentally observed with the LIF generated real time high-resolution images, as were changes in piston and ring design.

A spark-ignition engine friction model developed by Patton et al. in the late 1980s was evaluated against current engine friction data, and improved. The model, which was based on a combination of fundamental scaling laws and empirical results, includes predictions of rubbing losses from the crankshaft, reciprocating, and valvetrain components, auxiliary losses from engine accessories, and pumping losses from the intake and exhaust systems. These predictions were based on engine friction data collected between 1980 and 1988. Some of the terms are derived from lubrication theory. Other terms were derived empirically from measurements of individual friction components from engine teardown experiments. Recent engine developments (e.g., improved oils, surface finish on piston liners, valve train mechanisms) suggested that the model needed updating.

A set of experiments was performed to investigate the effects of relative air-fuel ratio, inlet boost pressure, and compression ratio on engine knock behavior. Selected operating conditions were also examined with simulated hydrogen rich fuel reformate added to the gasoline-air intake mixture. For each operating condition knock limited spark advance was found for a range of octane numbers (ON) for two fuel types: primary reference fuels (PRFs), and toluene reference fuels (TRFs). A smaller set of experiments was also performed with unleaded test gasolines. A combustion phasing parameter based on the timing of 50% mass fraction burned, termed “combustion retard”, was used as it correlates well to engine performance. The combustion retard required to just avoid knock increases with relative air-fuel ratio for PRFs and decreases with air-fuel ratio for TRFs.

Engine oil consumption is recognized to be a significant source of pollutant emissions. Unburned or partially burned oil in the exhaust gases contributes directly to hydrocarbon and particulate emissions. In addition, chemical compounds present in oil additives poison catalytic converters and reduce their conversion efficiency. Oil consumption can increase significantly during critical non-steady operating conditions. This study analyzes the oil consumption behavior during ramp transients in load by combining oil consumption measurements, in-cylinder measurements, and computer-based modeling. A sulfur based oil consumption method was used to measure real-time oil consumption during ramp transients in load at constant speed in a production spark ignition engine. Additionally in-cylinder liquid oil behavior along the piston was studied using a one-point Laser-Induced-Fluorescence (LIF) technique.

As part of ongoing research on hydrogen-enhanced lean burn SI engines, this paper details an experimental combustion system optimization program. Experiments focused on three key areas: the ignition system, in-cylinder charge motion produced by changes in the inlet ports, and uniformity of fuel-air mixture preparation. Hydrogen enhancement is obtained with a H2, CO, N2 mixture produced by a fuel reformer such as the plasmatron. The ignition system tests compared a standard inductive coil scheme against high-energy discharge systems. Charge motion experiments focused on the impact of different flow and turbulence patterns generated within the cylinder by restrictor plates at the intake port entrance, as well as novel inlet flow modification cones. The in-cylinder fluid motion generated by each configuration was characterized using swirl and tumble flow benches. Mixture preparation tests compared a standard single-hole pintle port fuel injector against a fine atomizing 12-hole injector.

This paper reviews the major changes that have occurred in spark-ignition engine design and operation over the last two decades. The automobile air pollution problem, automobile emission standards, and automobile fuel economy standards -- the factors which have and are producing these changes -- are briefly described. The major components in spark-ignition engine emission control systems are outlined, and advances in carburetion, fuel injection, ignition systems, spark retard and exhaust gas recycle strategies, and catalytic converters, are reviewed. The impact of these emission controls on vehicle fuel economy is assessed. The potential for fuel economy improvements in conventional spark-ignition engines is examined, and promising developments in improved engine and vehicle matching are outlined.

An experimental study was performed to investigate the effects of various intake charge motion control valves (CMCVs) on mixture preparation, combustion, and hydrocarbon (HC) emissions during the cold start-up process of a port fuel injected spark ignition (SI) engine. Different charge motions were produced by three differently shaped plates in the CMCV device, each of which blocked off 75% of the engine's intake ports. Time-resolved HC, CO and CO2 concentrations were measured at the exhaust port exit in order to achieve cycle-by-cycle engine-out HC mass and in-cylinder air/fuel ratio. Combustion characteristics were examined through a thermodynamic burn rate analysis. Cold-fluid steady state experiments were carried out with the CMCV open and closed. Enhanced charge motion with the CMCV closed was found to shorten the combustion duration, which caused the location of 50% mass fraction burned (MFB) to occur up to 5° CA earlier for the same spark timing.

In an effort to both increase engine efficiency and generate new, consistent, and reliable data useful for the development of engine concepts, a modern single-cylinder 4-valve spark-ignition research engine was used to determine the response of indicated engine efficiency to combustion phasing, relative air-fuel ratio, compression ratio, and load. Combustion modeling was then used to help explain the observed trends, and the limitations on achieving higher efficiency. This paper analyzes the logic behind such gains in efficiency and presents correlations of the experimental data. The results are helpful for examining the potential for more efficient engine designs, where high compression ratios can be used under lean or dilute regimes, at a variety of loads.

In this paper, a previously developed and experimentally-validated piston secondary motion model has been improved further numerically and applied to understand the detailed interactions between the piston skirt and cylinder liner for various piston design parameters. The model considers the roughness of the surfaces and the topography of the skirt in both the axial (barrel profile) and circumferential directions (ovality). Three modes of lubrication: hydrodynamic, mixed, and boundary lubrication regimes have been considered and the skirt is partially flooded in most cases. Elastic deformation of the skirt is an essential part of the model. In this model, the piston dynamic behavior, frictional and impact forces are predicted as functions of crank angle and are examined in detail. Parameters investigated include piston skirt profile, piston to liner clearance, surface roughness, and oil availability.

The flow into and out of the piston top-land crevice of a spark-ignition engine has been studied, using a square-cross-section single-cylinder engine with two parallel quartz glass walls which permit optical access to the entire cylinder volume. Schlieren short-time exposure photographs and high speed movies were used to define the essential features of this flow. The top-land crevice and the regions behind and between the rings consist of volumes connected through the ring gaps. A system model of volumes and orifices was therefore developed and used to predict the flow into and out of the crevice regions between the piston, piston rings and cylinder wall.

This vehicle simulation study estimates the fuel economy benefits of an HCCI engine system and assesses the NOx, HC and CO aftertreatment performance required for compliance with emissions regulations on U.S. and European regulatory driving cycles. The four driving cycles considered are the New European Driving Cycle, EPA City Driving Cycle, EPA Highway Driving Cycle, and US06 Driving Cycle. For each driving cycle, the following influences on vehicle fuel economy were examined: power-to-weight ratio, HCCI combustion mode operating range, driving cycle characteristics, requirements for transitions out of HCCI mode when engine speeds and loads are within the HCCI operating range, fuel consumption and emissions penalties for transitions into and out of HCCI mode, aftertreatment system performance and tailpipe emissions regulations.

A cycle by cycle analysis of engine behavior during the first few cycles of cranking and start-up was performed on a production four-cylinder engine. Experiments were performed to elucidate the effects of initial engine position (rest position after last engine shut-down), first and second cycle fueling, engine temperature, and spark timing on fuel delivery to the cylinder, engine-out Hydrocarbon (EOHC) emissions, and Gross Indicated Mean Effective Pressure (IMEPg). The most important effect of the piston starting position is on the first firing cycle engine rpm, which influences the IMEPg through combustion phasing. Because of the low rpm values for the first cycle, combustion is usually too advanced with typical production engine ignition timing. For both the hot start and the ambient start, the threshold for firing is at an in-cylinder air equivalence ratio (λ) of 1.1.

In analyzing the processes inside the cylinder of an internal combustion engine, the principal diagnostic at the experimenter's disposal is a measured time history of the cylinder pressure. This paper develops, tests, and applies a heat release analysis procedure that maintains simplicity while including the effects of heat transfer, crevice flows and fuel injection. The heat release model uses a one zone description of the cylinder contents with thermodynamic properties represented by a linear approximation for γ(T). Applications of the analysis to a single-cylinder spark-ignition engine, a special square cross-section visualization spark-ignition engine, and a direct-injection stratified charge engine are presented.

The effects of the directed port flow produced by a Charge-Motion-Control-Valve (CMCV) on mixture preparation in a Port-Fuel-Injection engine were assessed under conditions typical of fast idle in a cold start process. The port fuel was found to comprise two components: a “valve” puddle (at the vicinity of the valve) that built up quickly, and that was mainly responsible for the delivery of the fuel to the cylinder charge; a “port” puddle located significantly upstream. The latter was mainly created by the reverse back flow process and built up slowly. Although the fuel amounts in these two components were roughly the same, the latter did not significantly interact with the fuel transport to the cylinder charge. The CMCV only weakly affected the purging or filling time of the valve puddle, hence the dynamics of the fuel delivery process was not materially affected.

Liquid fuel flow into the cylinder an important source of hydrocarbon (HC) emissions of an SI engine. This is an especially important HC source during engine warm up. This paper examines the phenomena that determine the inflow of liquid fuel through the intake valve during a simulated start-up procedure. A Phase Doppler Particle Analyzer (PDPA) was used to measure the size and velocity of liquid fuel droplets in the vicinity of the intake valve in a firing transparent flow-visualization engine. These characteristics were measured as a function of engine running time and crank angle position during four stroke cycle. Droplet characteristics were measured at 7 angular positions in 5 planes around the circumference of the intake valve for both open and closed-valve injection. Additionally the cone shaped geometry of the entering liquid fuel spray was visualized using a Planar Laser Induced Fluorescence (PLIF) setup on the same engine.

Homogeneous-Charge-Compression-Ignition (HCCI) engine operation in a vehicle drive cycle is a very dynamic process. In this paper, a controller is devised on the premise that the vehicle is operating under Drive-By-Wire so that the driver commands the engine torque output according to the perceived vehicle speed. Thus a load-following controller is appropriate. Such a controller was developed for a single cylinder engine with electromagnetic variable valve timing control (also known as Controlled-Auto-Ignition (CAI) operation). Under open-loop operation within the CAI regime, the results indicated that the engine response was bipolar in nature: (a) the engine either responded quasi-statically to the open-loop control, or (b) the CAI combustion failed. The latter happened in a load increase process in which the per-cycle increment was too high.

Gasoline HCCI engine has the potential of providing better fuel economy and emissions characteristics than the current SI engines. However, management of HCCI operation for a vehicle is a challenging task. In this paper, the issues of mode transitions between the Spark Ignition and HCCI regimes, and the dynamic nature of the load trajectory within the HCCI regime are considered. Then the phenomena encountered in these operations are illustrated by the data from a single-cylinder engine with electromagnetic-variable-valve timing control. Mode transitions from the SI to HCCI regime may be categorized as robust and non-robust. In a robust transition, every intended HCCI cycle is successful. In a non-robust transition, one or more intended HCCI cycles misfire, although the cycles progress to a satisfactory HCCI operating point in steady state. (The spark ignition was kept on so that the engine could recover from a misfired cycle.)