Search Results

As motor assembly of Battery Electric Vehicle (BEV) replaces engine system of Internal Combustion Engine (ICE) vehicle, interior structure-borne noise induced by road random excitation becomes more prominent under middle and high speed. The research is focused on central driving type BEV. In order to improve interior noise in middle and low frequency range, dynamic load of BEV body must be identified. Consequently the structural noise induced by road excitation is conducted. The limitations of common identification method for dynamic body load are analyzed. The applied several identification methods are proposed for deterministic dynamic load such as engine or motor. Random dynamic load generated by road excitation is different from deterministic dynamic load. The deterministic load identification method cannot be applied to the random load directly. An identification method of dynamic body load for BEV is presented based on power spectrum decomposition.

Squeal noise in vehicle disc brakes is perceived by comsumers as both annoying and warranty cost. The mechanism is considered a mode coupling phenomenon also referred to as coalescence. In this paper, the system eigenvalues have been computed using a technique based on the • nite element method in order to obtain the dynamical properties of the disc brake assembly. The simulated squeal results were compared with the brake noise test that was in accordance with SAE J2521 standard and showed good correlation for some squeal frequencies which indicated that the research on disc brake squeal using complex mode could predict squeal propensity of the disc brake. Among the methods that have been used to control squeal noise, increasing the system damping has been shown to be very effective. The most commonly used method to increase system damping consists of attaching multi-layer laminates on the back of the brake pads.

The multi-functional mechanical arm equipped on engineering vehicle can achieve different functions by installing different mechanism devices through the interface at the end of the mechanical arm. It can achieve functions like engineering construction and road rescue. Mechanical arm systems often work in complex environments, which requires good reliability and safety of the boom system. When the mechanical boom is working, the pressure of each luffing cylinder is large, and the contact force and acceleration of each boom are complex, which requires a certain degree of verification and optimization before it can be put into production. In this paper, a virtual prototype of a vehicle mounted hydraulic mechanical arm with four booms is established. Through ADAMS, the dynamic analysis of mechanical arm under multiple working conditions is carried out, the movement parameter changes and the pressure changes of each luffing cylinder are analyzed.

Energy has the worldwide concern since the World War. Recently, the energy harvesting technology has got more attraction in different fields and applications. Hence, in a world where energy becomes rare and expensive, even the small quantities are worth to be harvested where it can be exploited in different applications. Vehicle suspension is one of the vibration power dissipation sources in which the undesired vibration is dissipated into heat waste. Accordingly, the principal motivation of this study is exploitation the conflict between the potentially harvested power and vehicle dynamics in automotive suspension system induced by road irregularity. Therefore, in terms of RMS conflict diagrams, the conflict between the potential power and vehicle dynamics are sufficiently and comprehensively defined considering a vehicle speed of 20 m/s.

Blade Electric Vehicle (BEV) with a light body plays an important role in saving the energy and reducing the exhaust emission. However, reducing the body weight need to meet the heterogeneous attributes such as structural, safety and NVH (Noise, Vibration and Harshness) performance. With the rapid development of finite element (FE) analysis technology, simulation analysis is widely used for researching the complex engineering design problem. Multidisciplinary Design Optimization (MDO) of a BEV body is a challenging but meaningful task in the automotive lightweight. In present research, the MDO is introduced to optimize a BEV Body-in-White (BIW).

With great development of thermoelectric exhaust heat recovery technology, more and more attention has been paid to optimization of automotive thermoelectric generators (ATEGs). A lot of work has been done on optimization of flow field and thermal analysis. However, investigation on acoustic optimization is rather limited. In this paper, efforts have been paid to study the acoustic performance of a flat-plate TEG, and the feasibility of integration of automotive exhaust thermoelectric generator with muffler was discussed. The internal configuration of heat exchanger looks like “fishbone”. Four factors have been taken into consideration: the spacing of two fins, angle of the fins, the diameter of inlet and outlet of exchanger; and filling sound absorbing material in heat exchanger chamber. Based on these four factors, acoustic analysis was carried out.

The active sound generation systems (ASGS) for electric vehicles (EVs) play an important role in improving sound perception and transmission in the car, and can meet the needs of different user groups for driving and riding experiences. The active sound synthesis algorithm is the core part of ASGS. This paper uses an efficient variable-range fast linear interpolation method to design a frequency-shifted and pitch-modified sound synthesis algorithm. By obtaining the operating parameters of EVs, such as vehicle speed, motor speed, pedal opening, etc., the original sound signal is interpolated to varying degrees to change the frequency of the sound signal, and then the amplitude of the sound signal is determined according to different driving states. This simulates an effect similar to the sound of a traditional car engine. Then, a dynamic superposition strategy is proposed based on the Hann window function.

The aerodynamic noise of the reactive muffler is generated inside the muffler and mixed with the noise of the muffler body, which is difficult to be measured in the exhaust system. Based on two-microphone transfer function method and transmission loss of mufflers in the absence of airflow, this paper proposes a method for measuring the aerodynamic noise of the muffler. On the built-in muffler aerodynamic noise test bench, a special sampling tube was designed to measure the aerodynamic noise of the muffler at different flow velocity. For the sound absorption end with large reflection coefficient, the test and simulation data have large error at low frequency, and a correction formula that can eliminate the reflection of sound waves at the end of the test pipeline and form multiple reflections in the upstream and downstream is derived.

The ride performance and stability of the vehicle will decrease while the vehicle passing a deceleration bump with relatively high speed. If the speed is too low, the road efficiency and ride comfort will be affected. It is essential to identify the proper speed taking into account all the factors. In this paper, the dynamic model of the vehicle passing through the deceleration bump is established. Three kinds of indicators vibration weighted acceleration RMS, maximum vertical vibration acceleration and wheel load impact coefficient, are used to comprehensively evaluate the ride comfort and safety. The highway model, vehicle model, and common trapezoidal cross-sections bump models are set up in Carsim. Parameters such as vertical acceleration and tire force at different vehicle speeds are obtained. Then use the spline interpolation method to fit the data, and comprehensively consider the three indicators to get the best speed.

The technology of active sound generation (ASG) for automobiles is one of the most effective methods to flexibly achieve the sound design that meets the expectations of different user groups, and the active sound synthesis algorithms are crucial for the implementation of ASG. In this paper, the Kaiser window function-based the harmonic synthesis algorithm of automobile sound is proposed to achieve the extraction of the order sounds of target automobile. And, the suitable fitting functions are utilized to construct the mathematical model between the engine speed information and the amplitude of the different order sound. Then, a random phase correction algorithm is proposed to ensure the coherence of the synthesized sounds. Finally, the analysis of simulation results verifies that the established method of the extraction and synthesis of order sound can meet the requirements of target sound quality.

Signage recognition is one of the hot topics in recent years. It has important applications in intelligent traffic and autonomous driving of smart cars. This paper designs a road marking recognition method combining OPSA point set distance and wavelet transform. The method consists of three main phases: 1) image denoising, restoration, 2) feature extraction, and 3) image recognition. First, a Gaussian-smoothing filter used to attenuate or remove irrelevant information in the image, enhance related information in the image, and achieve image denoising. In the feature extraction stage, the feature extraction and recognition method based on wavelet transform adopted to overcome the deficiency of the traditional Fourier feature extraction method, ensure that high frequency information is not lost, and low frequency information is not lost. Finally, the OSPA point set used to identify distance markers.

A vehicular hydraulic electrical energy regenerative semi-active suspension(HEERSS) was presented, and its working principle and performance were analyzed. Firstly, configuration and working principle of the HEERSS were described; Secondly, kinetic equation of HEERSS was deduced, and a skyhook controller was designed for HEERSS. The traditional skyhook control strategy should be changed for the characteristic of HEERSS, because the damping force during extension stroke could be controlled, but not in compression stroke. Thirdly, the performance of HEERSS was compared with passive suspension(PS), traditional semi-active suspension(TSS). The simulation results indicated that the performance of HEERSS would be compromise between TSS and PS, but the HEERSS could harvest vibration energy which was advanced than TSS and PS.

During the drivability test process, a large amount of noise generated by a series of internal and external factors of the vehicle reduces the accuracy of the drivability evaluation. To solve this problem, this paper introduces the EEMD denoising method and compares the denoising effects of the EMD denoising method and EEMD denoising method on the original signal using the entropy weight evaluation index. In addition, the optimal parameter setting is obtained by comparing the denoising results of different parameter settings in the EEMD denoising method. The results show that when the white noise is integrated 3000 times and the standard deviation of white noise is 0.1, the EEMD noise reduction method is the best, and the comprehensive score of noise reduction is 0.732 points higher than that of EMD.

Based on the technology of the order tracking and extraction, a software for the modulation of sound quality of automotive order sound is developed in this paper. The order analysis, the amplitude modulation of order sound in specific speed range and the calculation of the functional expression of the order sound amplitude are integrated in this software. Furthermore, a side-valve interpolation correction algorithm (SV-ICA) is proposed to solve the problem that the smooth transition of the order sound curve at endpoints cannot be guaranteed, which would result in the appearance of abnormal noise in the modulated sounds. The application of built software in constructing the automobile sounds with the sound quality of sportiness is demonstrated.

When vehicle traveling on the bumpy road or vehicle acceleration and deceleration, which will cause the body vibration of vehicle, at the same time, a large part of energy would be absorbed by the shock absorber transforms the mechanical energy into heat energy dissipated. In order to recycle the energy of vibration and keep the stability of running car, this paper provides the shock absorber of energy recovery that recycling the energy dissipated from the traditional absorber. The shock absorber includes rod and rodless chamber cavity, the two parts contain oil outlet and oil inlet, which connected to a bridge type loop of hydraulic to make pulsating oil pressure towards one direction, when the shock absorber vibration causes pulsating oil pressure, it drives hydraulic pump operation. Because the output shaft of the hydraulic pump fixedly attached to the input shaft of generator, so the generator produces electricity for recycling energy[1].

Glass lifter is a key part of automobile door system. Guide rail is the carrier of glass lifter, and it bears various load cases when glass lifer works. Mass, stiffness and natural frequencies are the factors that influence the performance of glass lifter. In order to design a lighter and reasonable glass lifter, topology optimization methods are studied in this paper. In a rope-wheel glass lifter, design domain is determined by the mechanical structure and working conditions. Firstly, the single target continuum structure topology optimization mathematic models of guide rail are built in this paper, and analysis of multi-stiffness topology optimization are carried out accordingly in which volume fraction is set as 0.4, 0.5 and 0.6. These models are based on SIMP (Solid Isotropic Material with Penalization) theory.

In the process of truck overload and over-limit detection, it is necessary to detect the characteristics of the vehicle's size, type, and wheel number. In addition, in some vehicle vision-based load recognition systems, the vehicle load can be calculated by detecting the vibration frequency of specific parts of the vehicle or the change in the length of the suspension during the vehicle's forward process. Therefore, it is essential to quickly and accurately identify vehicle features through the camera. This paper proposes a vehicle feature recognition method based on image semantic segmentation and Python, which can identify the length, height, number of wheels and vibration frequency at specific parts of the vehicle based on the vehicle driving video captured by the roadside camera.