Search Results

The objectives of the present work are to investigate the regulated and unregulated (particle) emissions of a classical and modern 2-stroke and a typical 4-stroke scooter with different ethanol blend fuels. There is also comparison of two different ethanol fuels: pure ethanol (E) *) and hydrous ethanol (EH) which contains 3.9% water and is denatured with 1.5% gasoline. Special attention is paid in this research to the hydrous ethanol, since the production costs of hydrous ethanol are much less than those for (dry) ethanol. The vehicles are with carburettor and without catalyst, which represents the most frequent technology in Eastern Asia and offers the information of engine-out emissions. Exhaust emissions measurements have been performed with fuels containing ethanol (E), or hydrous ethanol (EH) in the portion of 5, 10, 15 and 20% by volume. During the test systematical analysis of particle mass (PM) and nano-particles counts (NP) were carried out.

This paper presents an overview of the evolution & revolution of automotive E/E architectures and how we at Bosch, envision the technology in the future. It provides information on the bottlenecks for current E/E architectures and drivers for their evolution. Functionalities such as automated driving, connectivity and cyber-security have gained increasing importance over the past few years. The importance of these functionalities will continue to grow as these cutting-edge technologies mature and market acceptance increases. Implementation of these functionalities in mainstream vehicles will demand a paradigm shift in E/E architectures with respect to in-vehicle communication networks, power networks, connectivity, safety and security. This paper expounds on these points at a system level.

This paper provides an overview about the consequences of a 14/42 V - Electrical Power Supply System for the Electrical Interconnection and Switching Technology. It presents design guidelines and solutions for connector systems including advanced applications like fuse and relay boxes and gives an overview of those existing connectors already suited for 42 V and even higher voltages. The problem of arcing due to the increased voltage is discussed for the case that mating and unmating under load has to be taken into consideration. Arcing also has a tremendous impact on the design of 42 V proof relays. Therefore, some basic results be presented along with proposals how these problems can be overcome by appropriate designs. Another part of the paper looks at the electrical power supply system itself. Here interconnection techniques for new battery systems are discussed. Finally, the chances for new technologies are highlighted.

Background of the Pure Oil performance trials on six classes of automobiles is presented and the evolution of test requirements described. Three tests are run: the economy test to establish how far a vehicle can go over a prescribed course on one gallon of gasoline; the acceleration test which determines acceleration time from 25 to 70 mph in seconds; and the braking test where stopping distance in feet is measured for a stop from 60 mph. Each test is described from the point of view of rules, recording instruments, and penalties for infractions of rules. Test results are presented.

A review of the Pure Oil Performance Trials conducted at Daytona International Speedway are presented. Background information pertaining to conducting of tests, design of the equipment, and instrumentation required for the various events are discussed. The performance trials have evolved into three basic tests -- Economy, Acceleration, and Braking. The objective of the Performance Trials is to provide data that motorists can utilize in evaluating new cars and selecting new models.

A gasoline Road Octane study was conducted by the Coordinating Research Council (CRC) to evaluate the effects of heavy aromatics (C9 and heavier) and ethanol content on Road Octane performance independent of Research Octane Number (RON) and Motor Octane Number (MON). Maximum-throttle and part-throttle Road ON’s were found to be well predicted by equations containing only RON and MON terms. Heavier aromatics were found to have a small adverse effect on both maximum-throttle and part-throttle Road ON independent of its direct effects on RON and MON. The all-car data did not show a significant ethanol-content effect, but eight of the thirty-seven cars did show significant effects for ethanol content.

Controlled Auto Ignition (CAI), also known as Homogeneous Charge Compression Ignition (HCCI), is one of the most promising combustion technologies to reduce the fuel consumption and NOx emissions. Currently, CAI combustion is constrained at part load operation conditions because of misfire at low load and knocking combustion at high load, and the lack of effective means to control the combustion process. Extending its operating range including high load boundary towards full load and low load boundary towards idle in order to allow the CAI engine to meet the demand of whole vehicle driving cycles, has become one of the key issues facing the industrialisation of CAI/HCCI technology. Furthermore, this combustion mode should be compatible with different fuels, and can switch back to conventional spark ignition operation when necessary. In this paper, the CAI operation is demonstrated on a 2-stroke gasoline direct injection (GDI) engine equipped with a poppet valve train.

The Ford GT Program Team was allocated just 22 months from concept to production to complete the Electrical and Electronics systems of the Ford GT. This reduced vehicle program timing - unlike any other in Ford's history -- demanded that the team streamline the standard development process, which is typically 54 months. This aggressive schedule allowed only 12 weeks to design the entire electrical and electronic system architecture, route the wire harnesses, package the components, and manufacture and/or procure all components necessary for the first three-vehicle prototype build.

This paper is intended to give a general overview of the key aerodynamic developments for the 2006 Chevrolet Corvette C6 Z06. Significant computational and wind tunnel time were used to develop the 2006 Z06 to provide it with improved high speed stability, increased cooling capability and equivalent drag compared to the 2004 Chevrolet Corvette C5 Z06.

The 2013 SRT Viper Carbon Fiber X-Brace, styled by Chrysler's Product Design Office (PDO), is as much of a work of art as it is an engineered structural component. Presented in this paper is the design evolution, development and performance refinement of the composite X-Brace (shown in Figure 1). The single-piece, all Carbon Fiber Reinforced Plastic (CFRP) X-Brace, an important structural component of the body system, was developed from lightweight carbon fiber material to maximize weight reduction and meet performance targets. The development process was driven extensively by virtual engineering, which applied CAE analysis and results to drive the design and improve the design efficiency. Topology optimization and section optimization were used to generate the initial design's shape, form and profile, while respecting the package requirements of the engine compartment.

The fuel injection in internal combustion engines plays a crucial role in the mixture formation, combustion process and pollutants' emission. Its correct modeling is fundamental to the prediction of an engine performance through a computational fluid dynamics simulation. In the first part of this work a tridimensional numerical simulation of a multi-hole’s injector, using ethanol as fuel, is presented. The numerical simulation results were compared to experimental data from a fuel spray injection bench test in a quiescent vessel. The break up model applied to the simulation was the combined Kelvin-Helmholtz Rayleigh-Taylor, and a sensitivity analysis of the liquid fuel penetration curve, as well on the overall spray shape was performed according to the model constants. Experimental spray images were used to aid the model tuning. The final configuration of the KH-RT model constants that showed best agreement with the measured spray was C3 equal to 0.5, B1, 7 and Cb, 0.

3M is committed to continuously improving products and their manufacture toward the goal of sustainability. The 3M Life Cycle Management (LCM) program has been established to implement this goal. It utilizes a matrix tool to facilitate the review. The matrix consists of LCM Stage (Material Acquisition, R&D Operations, Manufacturing Operations, and Customer Use/Disposal) and Impact (Environment, Health, Safety, and Energy/Resources). The program is coordinated at the staff level by the Corporate Product Responsibility group. The corporate goal is to apply LCM to all new and existing products. The LCM program started with evaluations of new products within business units. Since 3M produces more than 60,000 products manufactured from more than 10,000 different raw materials, the routine evaluation of individual products challenges available staff and business unit resources. A technology-based approach for doing LCMs has been implemented to meet the challenge.

This paper aims at providing the scientific community with an overview of the H2020 European project 3beLiEVe and of its early achievements. The project has the objective of delivering the next generation Lithium-Nickel-Manganese-Oxide (LNMO) battery cells, in line with the target performance of the “generation 3b” Li-ion battery technology, as per EU SET-plan Action 7. Its activities are organized in three main pillars: (i) developing the 3b next generation LMNO battery cell, equipped with (ii) an array of internal and external sensors and complemented by (iii) manufacturing and recycling processes at scale. At present, 3beLiEVe is approaching the completion of its first project year (out of a total project planned duration of 42 months). Hence this paper, beyond presenting the overall project’s structure and objectives, focuses on its earliest results in the fields of the cell material formulation, arrangement of sensors and design of the battery pack.

The automotive industry is transitioning from the present 14V electrical system to a 42V system. This voltage evolution is due to the number of new systems (safety, fuel economy and customer convenience) being developed which require increased electrical power that a 14V system cannot deliver. During this transition, it will be necessary to control 14V subsystems in a 42V architecture. This paper presents 42V PWM (Pulse Width Modulation) voltage conversion and control technologies as a solution to control these 14V subsystems.

Titanium alloy for forging and pure titanium material for exhaust systems have been developed. The forging alloy will be applied to production of lightweight motorcycle frames and the pure titanium will be applied to improve engine performance. The materials have been made inexpensive by the use of off-grade sponge that includes many impurities for production of titanium ingot. Stable characteristics have been obtained by controlling oxygen equivalent after setting the volume of tolerable impurities by considering mechanical properties and production engineering. In spite of low-cost, the material provides the same design strength compared to conventional material, and enables parts production with existing equipment. A review of manufacturing and surface treatment processes indicated a reduction in the price of titanium parts produced with this new material.

FOUR-WHEEL STEERING (4WS) is beginning to find widespread use as a new approach to improving vehicle dynamics, especially in the medium and high speed ranges. Steering the rear wheels in the same phase as the front wheels enhances vehicle stability. Four-wheel steering systems have an even greater potential to improve stability and steering response through suitable control over the transient characteristics of the rear wheel steer angle. This paper traces the course of Nissan research and development work on four-wheel steering and the evolution of Nissan's HICAS (4WS) technology. It also describes research activities under way on vehicle dynamics using a newly developed Simulator Vehicle, equipped with a front and rear angle transient control system which makes it possible to vary the dynamic characteristics of the vehicle instantaneously and at will while driving.

This paper will provide an overview of the work progress of the advanced offset frontal crash protection group of IHRA. It resumes, including tables, the strategy of the group to cope with the assigned task. This is the commitment to achieve an harmonized frontal crash protection procedure taking into account the different world wide views in this field.

A colorful series of 150 slides was presented tracing 5 HP to 1200 HP marine gear design evolution beginning in 1906, followed by pre-WWI developments, Liberty Aircraft engine usage and a 1924 to 1972 series of pleasure boat and work boat marine gear photographs. The entire slide presentation is available in 35 m.m. film strip and may be ordered (at cost) from the author, R. C. McRoberts, Twin Disc, Incorporated, Racine, Wisconsin, 53403, U.S.A. For short time usage, a loan film is available. This history of U. S. marine gear development includes information contributed by the Snow-Nabstedt Gear Corp., Capitol Gears, Inc., Paragon Gears, Inc., The Walter Machine Co., Inc., Detroit Diesel Allison Div. of General Motors Corp., Caterpillar Tractor Co., Warner Gear Div. Borg-Warner Corp. and Twin Disc, Incorporated.

In France, the current evolution in the number of road accident victims is less favourable for the moped rider category than for the majority of others. In addition, the proportion of scooters in the moped park is currently considerably increasing. The aim of the research work presented is to consider if an explanation for the bad results for this category of users, in terms of road safety, can be found through the study of the dynamic performances of this type of vehicle. We thus carried out an experiment aimed at comparing the dynamic capacities of a “Classic” moped with those of a “Scooter” model. Two mopeds, one of each type, were fitted with an embedded measurement system. They were driven for several tests on a track by a professional test pilot. The results of this study are more in favour of the “Scooter” moped, which seems to offer equivalent, or even better, dynamic capacities than the “Classic” one.