Search Results

HCCI combustion was studied in a 4-stroke gasoline engine with a direct injection system. The electronically controlled two-stage gasoline injection and spark ignition system were adopted to control the mixture formation, ignition timing and combustion rate in HCCI engine. The engine could be operated in HCCI combustion mode in a range of load from 1 to 5 bar IMEP and operated in SI combustion mode up to load of 8 bar IMEP. The HCCI combustion characteristics were investigated under different A/F ratios, engine speeds, starts of injection, as well as spark ignition enabled or not. The test results reveal the HCCI combustion features as a high-pressure gradient after ignition and has advantages in high thermal efficiency and low NOx emissions over SI combustion. At the part load of 1400rpm and IMEP of 3.5bar, ISFC in HCCI mode is 25% lower and NOx emissions is 95% lower than that in SI mode.

A new combustion mode namely multiple premixed compression ignition (MPCI) for gasoline engines was proposed. The MPCI mode can be realized by two or more times gasoline injections into cylinder with a high pressure around the compression TDC and featured with a premixed combustion after each injection in the cylinder, which is different from the existed gasoline direct injection compression ignition (GDICI) modes such as homogeneous charge compression ignition (HCCI) mode with gasoline injection occurred in intake stroke, and partially premixed compression ignition (PPCI) mode with multiple gasoline injections in intake and compression strokes before the start of combustion (SOC). Therefore the spray and combustion of the MPCI mode are alternatively occurred as "spray-combustion-spray-combustion" near the TDC, rather than "spray-spray-combustion" sequence as traditional PPCI gasoline engines.

Homogeneous charge combustion and emissions of ethanol ignited by pilot diesel fuel were investigated on a two-cylinder diesel engine. The results show that emissions depend on loads and ethanol volume fraction. At low loads, ethanol has little effects on smoke. With the increase of ethanol, NOx decreases, but CO emissions increase. At high loads, smoke emissions reduce greatly with increasing ethanol, but NOx and total hydrocarbon (THC) emissions increase. With the increase of ethanol, ignition delays, combustion duration shortens. The maximum rates of heat release for the fuel containing 10 vol% ethanol (E10) and 30 vol% ethanol (E30) increase. Brake specific energy consumption (BSEC) of E10 and E30 is improved slightly only at full loads. Compared to smoke emissions obtained on the same engine using ethanol blended diesel fuels, the tendency of smoke reduction is similar to that of homogeneous charge combustion of ethanol at the same operating conditions.

Fuel quality, including antiknock rating, plays a critical role in enabling optimal operation of advanced gasoline engines. As new designs introduced into the market implement technologies to improve fuel efficiency, the overall octane level of the gasoline pool may need to be increased to ensure optimal performance. Turbocharging, higher compression ratios and downsized displacement all lead to higher combustion pressures and temperatures that make engines more susceptible to knocking. All modern gasoline engines are equipped with knock sensors that detect abnormal combustion resulting from autoignition caused by insufficient octane quality. The ability of an engine to account for the use of lower octane fuel by retarding spark timing and enriching air-fuel ratio to reduce knock is limited, and engine efficiency is directly and adversely impacted when the use of lower octane gasoline is accommodated, resulting in higher fuel consumption.

The detailed chemical kinetics was implemented into the 0D single-zone model, 1D engine cycle model and 3D CFD model respectively. Both simulation and experiment were carried out on a four-stroke gasoline HCCI engine with direct injection. The 0D model (HRG) was developed to study the isolating effect of HCCI parameters. The 1D engine cycle model with HRG was established to study the gas exchange process and the direct injection strategy in the gasoline HCCI engine with two-stage direct injection (TSDI) and negative valve overlap (NVO). The 3D model with HRG was constructed to study the ignition control mechanism in “two-zone HCCI” combustion via analysis the auto-ignition spots distribution in combustion chamber. “Two-zone HCCI” is defined in this paper as premixed ultra-lean compression ignition combining with premixed ultra-rich compression ignition. The three models were validated by experiments.

This study improved the computational efficiency significantly using parallel computation and reduced mechanisms. A 3-dimensional engine moving mesh of intake port, exhaust port and combustion chamber was established for HCCI engine cycle simulation. To achieve a more accurate analysis, chemical kinetics was implemented into the CFD code to study the intake, spray, ignition, combustion, and pollution formation process in HCCI engine. The simulations were run on a cluster of 16-CPU, parallelized by Message-Passing Interface (MPI) mode. The cases with detailed and reduced reaction mechanisms were calculated using 1, 2, 4, 8, 16 CPUs respectively and the corresponding computational time and speed-up were discussed. Using MPI 8-CPU with reduced mechanism (less than 40 species) is the optimal scheme for CFD/Chemistry calculation of typical HCCI engine.

Diesel particulate filter (DPF) is necessary for diesel engines to meet the increasingly stringent emission regulations. Many studies have demonstrated that the lubricant derived ash has a significant effect on DPF pressure drop and engine fuel economy, and this effect becomes more and more severe with the increasing of operating hours of the DPF because the ash accumulated in the DPF cannot be removed by regeneration. It is reported that most of the DPFs operated with more ash than soot in the filter for more than three quarters of the time during its lifetime [1]. In order to mitigate this problem, the original engine manufacturers (OEM) tend to use an oversized DPF for the engine. However, it will increase the costs of the DPF and reduce the compactness of the engine aftertreatment system.

Two premixed compression ignition modes for low octane gasoline are numerically investigated. The multiple premixed compression ignition (MPCI) mode is featured with a sequence of “spray- combustion- spray- combustion”, while the partially premixed compression ignition (PPCI) mode is a sequence of “spray- spray- combustion”. This paper compares the combustion process of the two modes using multi-dimensional CFD code, KIVA-3v, which can perform chemical reaction calculations for different fuels by a discrete multiple component (DMC) method. The fuel used for simulation consists of 58.5% i-C8H18 and 41.5% n-C7H16 in volume, and has the same RON and similar physical properties to straight-run naphtha used in the experiment. The engine operating condition is fixed at a 1600rpm and 0.7 MPa IMEP. The injection strategies for these two modes are different. All of the parameters in the simulation come from the single cylinder engine experiments.

Gasoline direct injection engines can greatly improve the fuel economy, but the idea mixture distribution cannot be easily controlled. In this paper, the linearized instability sheet atomization (LISA) and large eddy simulation (LES) implemented into KIVA-3V code were used to study the gasoline hollow cone spray process for gasoline direct injection (GDI) in a constant volume vessel. The three-dimensional results show that the LISA model can effectively simulate the gasoline hollow cone spray and obtain the string structure compared to the experiment data. And the velocity interpolation method can reduce the grid dependency of spray simulation. Using dense grid (about 8 million cells) in LES and RANS all can obtain the good spray tip penetration and width. Unlike diesel spray, for gasoline spray there are not big difference between the results using LES and RANS. In additional the ambient pressure significantly influence the gasoline spray shape.

This paper studied the knock combustion process in gasoline HCCI engines. The complex chemical kinetics was implemented into the three-dimensional CFD code with LES (Large eddy simulation) to study the origin of the knock phenomena in HCCI combustion process. The model was validated using the experimental data from the cylinder pressure measurement. 3D-CFD with LES method gives detailed turbulence, species, temperature and pressure distribution during the gasoline HCCI combustion process. The simulation results indicate that HCCI engine knock originates from the random multipoint auto-ignition in the combustion chamber due to the slight inhomogeneity. It is induced by the significantly different heat release rate of high temperature oxidation (HTO) and low temperature oxidation (LTO) and their interactions.

Gasoline Direct Injection (GDI) engines developed at nineties of the twentieth century can greatly improve the fuel economy. But the combustion chamber design and mixture control of the engines are very complex compared with Port Fuel Injection (PFI) gasoline engines. A two-stage gasoline direct injection (TSGDI) combustion system is developed and aimed to solve the problem of the complexity. Two-stage fuel injection and flexible injection timings are adopted as main means to form reasonable stratified mixture in the cylinder. A simple combustion chamber and helical intake port are designed to assist the mixture's stable combustion, which reduces the difficulties of the combustion system design. Systematical simulation and experimental studies of the effects of injection strategies such as different first,second injection timings and injection ratios, on the mixture formation processes and engine performanc are made in detail.

Gasoline direct injection (GDI) engine technology is now widely used due to its high fuel efficiency and low CO2 emissions. However, particulate emissions pose one challenge to GDI technology, particularly in the presence of fuel injector deposits. In this paper, a 4-cylinder turbocharged GDI engine in the Chinese market was selected and operated at 2000rpm and 3bar BMEP condition for 55 hours to accumulate injector deposits. The engine spark timing, cylinder pressure, combustion duration, brake specific fuel consumption (BSFC), gaseous pollutants which include total hydro carbon (THC), NOx (NO and NO2) and carbon dioxide (CO), and particulate emissions were measured before and after the injector fouling test at eight different operating conditions. Test results indicated that mild injector fouling can result in an effect on engine combustion and emissions despite a small change in injector flow rate and pulse width.

In order to enhance the thermal efficiency of gasoline engines, a combustion mode namely Homogeneous Charge Induced Ignition (HCII) was introduced and examined in this paper. Port-injected gasoline was used as the main fuel and formed a homogeneous charge in the cylinder. Diesel was used as the pilot fuel, directly injected into the cylinder, and self-ignited and this induced the ignition of the premixed gasoline-air charge. The images of HCII combustion process were taken on an optical engine through a high-speed CMOS camera. The multi-point induced ignition phenomena were observed and the parameters like flame luminance, ignition delay and combustion duration were analyzed by image analysis. The result shows that as the gasoline/diesel ratio increases with a fixed low pilot amount, the ignition delay increases, the initial ignition area extends from the center towards the periphery of the combustion chamber, and the combustion velocity increased.