Search Results

This paper describes a comprehensive model of piston skirt lubrication, developed for use in conjunction with piston secondary dynamic analysis, to accurately characterize the effects of the skirt-cylinder oil film on piston motions. The model represents both hydrodynamic and boundary lubrication modes and applies an asperity contact pressure when surfaces are in close proximity with each other. In addition to skirt dimensions and surface roughness properties, the circumferential extent of lubrication, an arbitrary skirt profile and bore distortion are specifiable inputs to the model. The model is also extended to represent the oil starvation at the cylinder end of the skirt by allowing the axial extent of lubrication on the skirt surface to vary circumferentially and with time to satisfy continuity of oil.

A model for oil consumption due to in-cylinder evaporation of oil in reciprocating engines, has been developed. The model is based on conservation of mass and energy on the surface of the oil film left on the cylinder by a piston ring pack, at the oil/gas interface, and also conservation of energy within the oil film and cylinder/coolant interface. The model is sensitive to in-cylinder conditions and is part of an integrated model of ring pack performance, which provides the geometry of the oil film left by the ring pack on the cylinder. Preliminary simulation results indicate that a relatively small but not insignificant fraction (2-5%) of the total oil consumption may be due to evaporation losses for a heavy duty diesel at the rated condition. The evaporation rate was shown to be sensitive to oil grade and upper cylinder temperature. Much of these losses occur during the non-firing half of the cycle.

The duration of piston durability tests is often shortened by increasing mechanical and thermal engine loads and loading frequency. Such durability tests are useful for assessing the structural integrity of new piston designs, but test results are generally not indicative of the expected service life. Furthermore, improper test procedures can introduce illegitimate failure modes which are not present in actual service. Two aluminum pistons were analyzed to gain a fundamental understanding of piston response due to accelerated test loads. The influence of engine speed, fuel/air ratio, intake manifold pressure and crankcase oil temperature on piston fatigue life was studied. Guidelines were established to aid in developing a more effective durability test procedure for natural gas engine pistons.

An integrated simulation methodology for the analysis of piston tribology is presented. The methodology is comprised of coupled models of piston secondary dynamics, skirt oil film elastohydrodynamic lubrication and wristpin bearing hydrodynamics, developed earlier by the authors. Models have been further expanded to calculate distributions of cumulative wear load on the skirt and cylinder and to account for details of skirt crankcase end geometry. The skirt elasticity model has also been improved to account for the effects of piston crown and pin boss stiffness in conventional, one-piece pistons. The model predicts piston assembly secondary motions, piston (skirt) friction, skirt and wristpin oil film pressures, transient deformations, skirt-cylinder contact/impact pressures and skirt and cylinder wear loads.

Selective reinforcement of squeeze-cast aluminum pistons by fiber matrix inserts is a method of improving high temperature strength in piston zones subject to severe thermal and mechanical loads in highly loaded diesel engines. An investigation was carried out into the effects of selective fiber-matrix reinforcement on the thermal and stress state of an aluminum piston for a heavy-duty truck diesel engine application. Specifically, effects of geometry of the reinforced zone (fiber matrix), fiber density in the matrix, fiber orientation and piston combustion bowl shape were sought. Thermal and structural finite element analysis of the configurations were carried out. Thermal analyses were fully coupled to a simulation of a highly rated heavy-duty diesel.

The advantages of Variable Valve Actuation (VVA) in the aspects of improved engine performance, fuel economy and reduced emissions are well known in the industry. However, the design and optimization of such systems is complex and costly. The design process of VVA mechanisms can be greatly accelerated through the use of sophisticated simulation tools. Predictive numerical analysis of systems to address design issues and evaluate design changes can assure the required performance and durability. One notable requirement for the analysis and design of novel mechanically-actuated VVA systems is a general-purpose fast and easy-to-use planar mechanism kinematics analyzer with cam solution/design features, which can be applied to general mechanisms.

A comprehensive diesel engine system model, representing in detail engine heat transfer processes, has been applied to a study of insulated diesel engines. The study involved a broad design analysis matrix covering a range of engine configurations with and without inter-cooling and exhaust heat recovery devices, three operating conditions and seven heat rejection packages. The main findig of this study is that the retained heat conversion efficiency (RHCE), of the in-cylinder heat retained by insulation to piston work, is 35-40 percent; these levels of RHCE are larger than those predicted by previous models. This means that a significant part of the retained heat is converted directly to piston work rather than being merely available in the exhaust stream, from which it would be recoverable with a much lower efficiency.

An increasing emphasis is being placed in the vehicle development process on transient operation of engines and vehicles, and of engine/vehicle integration, because of their importance to fuel economy and emissions. Simulations play a large role in this process, complementing the more usual test-oriented hardware development process. This has fueled the development and continued evolution of advanced engine and powertrain simulation tools which can be utilized for this purpose. This paper describes a new tool developed for applications to transient engine and powertrain design and optimization. It contains a detailed engine simulation, specifically focused on transient engine processes, which includes detailed models of engine breathing (with turbocharging), combustion, emissions and thermal warm-up of components. Further, it contains a powertrain and vehicle dynamic simulation.

Changing and more stringent emissions norms and fuel economy requirements often call for modifications in the fuel injection system of a Diesel engine. There exists a strong interaction between the injection system hydraulics and the dynamics of mechanical components within the unit injector and the camshaft-driven mechanical system used to pressurize it. Hence, accurate predictive analysis of design issues or evaluation of design changes requires highly coupled and integrated hydro-mechanical simulations, combining analysis of fuel injection hydraulics and the dynamics of all mechanical parts, including the cam-drive system. This paper presents an application of such an integrated model to the study and alleviation of an observed increase in mechanical vibration and related noise levels associated with a proposed design change in unit injectors and valve-train of a 6-cylinder truck diesel engine.

This paper describes a general model for the analysis of secondary motions in conventional and articulated piston assemblies. The model solves for the axial, lateral and rotational departures in positions and motions from the nominal kinematics, resulting from clearances within the piston assembly and also between the piston assembly components and the cylinder. The methodology allows the characterization of conventional and articulated piston secondary motions in the thrust plane of the cylinder. Motions of the piston, pin, rod and (for articulated pistons) skirt are separately calculated, by integrating equations of motion for individual components and dynamic degrees of freedom. Various configurations with respect to rigid attachment of the wristpin to other components can also be represented. In the equations of motions solved, all gas pressure, inertia, friction and oil or contact pressure forces are accounted for.

The warmup characteristics of an engine have an important impact on a variety of design issues such as performance, emissions and durability. A computer simulation has been developed which permits a detailed transient simulation of the engine warmup period from initial ambient conditions to a fully warmed up state. The simulation combines a detailed crankangle-by-crankangle calculation of in-cylinder processes and of engine air flow, with finite element heat conduction calculations of heat transfer from the gases, through the structure to the coolant. The paper describes one particular application of the simulation to the warmup of a 2.5ℓ spark ignited engine from cold start to a fully warmed up state at several speeds ranging from 1600 to 5200 rpm and loads ranging from 25% to 100% at each speed. The response of structure temperatures, charge temperature at IVC and of the exhaust temperature has been calculated and is documented in terms of characteristic warmup times.