Search Results

The wireless inter-vehicle communication provide a manner to achieve multi-vehicle cooperative driving, and the platoon of automotive vehicle can significantly improve traffic efficiency and ensure traffic safety. Previous researches mostly focus on the state of the proceeding vehicle, and transmit information from self to the succeeding vehicle. Nevertheless, this structure possesses high requirements for controller design and shows poor effect in system stability. In this paper, the state of vehicles is not only related to the information of neighbor vehicles, while V2V communication transmit information over a wide range of area. To begin with, the node dynamic model of vehicle is described by linear integrator with inertia delay and the space control strategy is proposed with different topological communication structures as BF, LBF, PBF, etc.

The platooning of connected automated vehicles (CAV) possesses the significant potential of reducing energy consumption in the Intelligent Transportation System (ITS). Moreover, with the rapid development of eco-driving technology, vehicle platooning can further enhance the fuel efficiency by optimizing the efficiency of the powertrain. Since road grade is a main factor that affects the energy consumption of a vehicle, the estimation of the road grade with high accuracy is the key factor for a connected vehicle platoon to optimize energy consumption using vehicle-to-vehicle (V2V) communication. Commonly, the road grade is quantified by single consumer grade global positioning system (GPS) with the geodetic height data which is rough and in the meter-level, increasing the difficulty of precisely estimating the road grade.

Nowadays, SC is recognized as a key element of hybrid energy storage system in modern energy supply chain for electric vehicles (EVs). Co9S8 as a promising electrode material attracts much attention for supercapacitor owing to its superior electrochemical capacity. However, its poor stability and electronic conductivity, which result in inferior cycling performance and rate capability, have seriously limited the practical application of Co9O8 in supercapacitors. In this article, Co9S8 nanoparticles were embedded in reduced graphene oxide (rGO) via a simple anneal approach as high efficient and stable electrodes for SCs. The Co9S8/rGO composites were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The Co9S8 nanoparticles were inserted tightly between the rGO layers due to strong intermolecular forces, preventing the cluster in reduction process of rGO from graphene oxide (GO).

The suspension system of a heavy truck's driver seat plays an important role to reduce the vibrations transmitted to the seat occupant from the cab floor. Air-spring is widely used in the seat suspension system, for the reason that its spring rate is variable and it can make the seat suspension system keep constant ‘tuned’ frequency compared to the conventional coil spring. In this paper, vibration differential equation of air-spring system with auxiliary volume is derived, according to the theory of thermodynamic, hydrodynamics. The deformation-load static characteristic curves of air-spring is obtained, by using a numerical solution method. Then, the ADAMS model of the heavy truck's driver seat suspension system is built up, based on the structure of the seat and parameters of the air-spring and the shock-absorber. At last, the model is validated by comparing the simulation results and the test results, considering the seat acceleration PSD and RMS value.

A vehicle-mounted anti-vibration system is designed to semi-actively reduce accelerations acting on vibration isolation platform under different road conditions. To provide the basis for optimal anti-vibration design, the kinematics and dynamics of the platform are analyzed to investigate the relationship between leg length, strength, the platform position and vibration properties. As the platform is fixed on vehicle, a combined vehicle-platform model is necessary for verifying the performance and applying some suitable control algorithms. Also, typical digital testing roads will be built using road load spectrum. To optimize the platform parameters, especially stiffness and damping, an active control system is designed at first. An anti-vibration system including a semi-active inerter is designed to match the control forces which are calculated from the above active system.

NVH quality is one of the most important criteria by which people judge the design of a vehicle. The Powertrain Mounting System (PMS), which can reduce the vibration from engine to vehicle cab as well as the inside noise, has attained significant attention. Much research has been done on the isolation method for three- and four-point mounting. But the six-point mounting system, which is usually equipped in commercial vehicle, is seldom studied and should be paid more attention. In this paper, the support rod installed on the upside of the transmission case is considered as a flexible body. Thus a rigid-flexible coupling model of PMS is established and the necessity of the established model is analyzed by comparing the simulation results of the new model and those of the conventional model.

In addition to ride comfort, handling stability and other conventional vehicle performances, we should also focus on other aspects of performance to a center axle trailer combination, such as the maximum stable side-inclination, the anti-rolling stability, the lateral stability and so on. Based on the finite element method, a rigid-flexible coupling model for the truck combination was built and analyzed in the multi-body environment (ADAMS), in which the key components of the chassis and cab suspension were treated as flexible bodies. A series of simulations were carried out to evaluate the lateral stability of the center axle trailer in accordance with the relevant regulations of the vehicle. The influence of design variables on the lateral stability was studied by an experiment. Furthermore, in order to improve the lateral stability of the trailer combination, the optimal design was obtained by the co-simulation of the ADAMS/Car, iSIGHT and Matlab.

The ride comfort of the commercial vehicle is mainly affected by several vibration isolation systems such as the primary suspension system, engine mounting system and the cab mounting system. A rigid-flexible coupling model for the truck was built and analyzed in multi-body environment (ADAMS). The method applying the excitation on the wheels center and the engine mountings in time domain was presented. The variables' effects on the ride performance were studied by design of experiment (DOE). The optimal design was obtained by the co-simulation of the ADAMS/View, iSIGHT and Matlab. It was found that the vertical root mean square (RMS) acceleration and frequency-weighted RMS acceleration on the seat track were reduced about 17% and 11% respectively at different speeds relative to baseline according to ISO 2631-1.

The structure optimization method for heavy truck propeller shaft bracket is presented in this research. A model including propeller shaft, mount, bracket and frame is established based on finite element analysis and rigid-flexible coupling analysis. Under the unbalanced excitation, the dynamic response of the propeller shaft and dynamic stress on the bracket are presented. The effects of bracket structure mode on the frequency response and stress on the bracket are studied. As an engineering example, the optimization design of a heavy truck propeller shaft bracket is presented and a final experimental verification is validated by a real vehicle test.

Lane-changing is a typical traffic scene effecting on road traffic with high request for reliability, robustness and driving comfort to improve the road safety and transportation efficiency. The development of connected autonomous vehicles with V2V communication provide more advanced control strategies to research of lane-changing. Meanwhile, four-wheel steering is an effective way to improve flexibility of vehicle. The front and rear wheels rotate in opposite direction to reduce the turning radius to improve the servo agility operation at the low speed while those rotate in same direction to reduce the probability of the slip accident to improve the stability at the high speed. Hence, this paper established Four-Wheel-Steering(4WS) vehicle dynamic model and quasi real lane-changing scenes to analyze the motion constraints of the vehicles.