Search Results

A direct injection system in which fuel was injected through the cylinder wall was developed and detailed investigation was made for the purpose of reducing short-circuit of fuel in 2-stroke engines. As a result of dynamo tests using 430cc single cylinder engine, it was found that the injector was best attached at a location as close to TDC as possible on the rear transfer port side, and that the entire amount of fuel should be injected towards the piston top surface. Emissions were worsened if fuel was injected towards the exhaust port or spark plug. Although the higher injection pressure resulted in large emissions reduction effects, it did not have a significant effect on fuel consumption. When a butterfly exhaust valve, known to be effective against irregular combustion in the light load range, was applied, it was found to lead to further reductions in HC emission and fuel consumption while also improving combustion stability.

The road transportation sector is undergoing significant changes, and new green scenarios for sustainable mobility are being proposed. In this context, a diversification of the vehicles’ propulsion, based on electric powertrains and/or alternative fuels and technological improvements of the electric vehicles charging stations, are necessary to reduce greenhouse gas emissions. The adoption of internal combustion engines operating with alternative fuels, like methanol, may represent a viable solution for overcoming the limitations of actual grid connected charging infrastructure, giving the possibility to realize off-grid charging stations. This work aims, therefore, at investigating this last aspect, by evaluating the performance of an internal combustion engine fueled with methanol for stationary applications, in order to fulfill the potential demand of an on off-grid charging station.

A drivetrain model incorporating detailed crankshaft and drivetrain dynamics has been incorporated into an unsteady gas dynamic computer simulation of a single-cylinder two-stroke engine. This study examines the change in predicted engine performance caused by relaxing the conventional assumption of constant crankshaft velocity, and a comparison of results is presented. Relaxing the assumption changed the predicted brake mean effective pressures by over 10%. Experimental validation of the simulation involved mounting an engine to a test bed and driving an inertia wheel through a fully characterized drivetrain. A high-speed data acquisition system measured signals from a position encoder mounted on the crankshaft and from a non-contact torque transducer. The time and position data were used to calculate instantaneous crankshaft speed, and these results were compared to the predicted profiles. Simulation results and experimental measurements are presented and discussed.

The characteristics of the combustion process in an improved design of a novel spark ignition engine studied by means of Computational Fluid Dynamics are presented. The engine is designed to work at low average combustion temperatures to achieve very low NOx emissions. The engine is a two-stroke, two piston in-line engine. The main combustion occurs in four combustion pre-chambers that have an annular shape with a nozzle on the side facing the cylinder. Fuel is directly injected into the pre-chambers by using high-pressure fuel injectors. A progressive burning process is expected to keep the flame inside the pre-chambers while the fast ejection of combustion products should produce effective mixing with the cold air in the cylinder. This fast dilution should guarantee a temperature drop of the combustion products thus reducing the formation of NOx via a thermal path.

Direct fuel injection is becoming mandatory in two-stroke S.I. engines, since it prevents one of the major problems of these engines, that is fuel loss from the exhaust port. Another important problem is combustion irregularity at light loads, due to excessive presence of residual gas in the charge, and can be solved by charge stratification. High-pressure liquid fuel injection is able to control the mixing process inside the cylinder for getting either stratified charge at partial loads or quasi-stoichiometric conditions, as it is required at full load. This paper shows the development of this solution for a small engine for moped and light scooter, using numeric and experimental tools. In order to obtain the best charge characteristics at every load and engine speed, different combustion chambers have been conceived and studied, examining the effects of combustion chamber geometry, together with injector position and injection timing

Homogeneous Charge Compression Ignition (HCCI) is good method to be higher efficiency and to reduce NOx emission and particular matter together than conventional SI combustion engine. But HCCI depends on chemical reaction of fuel and air mixture. So controlling of ignition timing is difficult, and HCCI is high THC and CO emissions because temperature can't reach the enough temperature to reduce those. In this study, we investigated factor for auto ignition timing and combustion completion on n-Butane/Air mixture by a two-stroke HCCI engine. Auto Ignition temperature are known to be decided by fuel(1), for n-Butane, the temperature was 1150±30K. And as we researched combustion completion from In-cylinder gas temperature, increasing In-cylinder gas temperature caused high combustion efficiency and low THC, CO emissions.

The paper presents a combined experimental and numerical investigation of a small unit displacement two-stroke SI engine operated with gasoline and Natural Gas (CNG). A detailed multi-cycle 3D-CFD analysis of the scavenging process is at first performed in order to accurately characterize the engine behavior in terms of scavenging patterns and efficiency. Detailed CFD analyses are used to accurately model the complex set of physical and chemical processes and to properly estimate the fluid-dynamic behavior of the engine, where boundary conditions are provided by a in-house developed 1D model of the whole engine. It is in fact widely recognized that for two-stroke crankcase scavenged, carbureted engines the scavenging patterns (fuel short-circuiting, residual gas distribution, pointwise lambda field, etc.) plays a fundamental role on both of engine performance and tailpipe emissions.

The paper presents a 1D-3D numerical model to simulate the scavenging and combustion processes in a small-size spark-ignition two-stroke engine. The engine is crankcase scavenged and can be operated with both gasoline and Natural Gas (NG). The analysis is performed with a modified version of the KIVA3V code, coupled to an in-house developed 1D model. A time-step based, two-way coupled procedure is fully described and validated against a reference test. Then, a 1D-3D simulation of the whole two-stroke engine is carried out in different operating conditions, for both gasoline and NG fuelling. Results are compared with experimental data including instantaneous pressure signals in the crankcase, in the cylinder and in the exhaust pipe. The procedure allows to characterize the scavenging process and quantify the fresh mixture short-circuiting, as well as to analyze the development of the NG combustion process for a diluted mixture, typically occurring in a two-stroke engine.

The transportation sector still depends on conventional engines in many countries as the alternative technologies are not mature enough to reduce carbon footprints in society. The four-stroke diesel engines, primarily used for heavy-duty applications, need either high intake boosting or a large bore to produce higher torque and power output. There is an alternative where a four-stroke engine operated in two-stroke mode with the help of a fully flexible variable valve actuation (VVA) system can achieve similar power density without raising the intake boosting or engine size. A fully flexible VVA is required to control the valve events (lift, timing, and durations) independently so that the four-stroke events can be completed in one cycle. In this study, 1D-3D CFD coupled simulations were performed to develop a gas exchange process for better air entrapment in the cylinder and evacuate the exhaust products simultaneously.

An investigation of the possibility to extend the 3-dimensional modeling capabilities from conventional diesel to the HCCI combustion mode simulation was carried out. Experimental data was taken from a single cylinder engine operating with early injections for the HCCI and a split-injection (early pilot+main) for the high speed Diesel engine operation. To properly phase the HCCI mode in the experiments, high amounts of cooled EGR and a decreased compression ratio were used. In numerical simulation performed using KIVA3-V code, modified to incorporate the Detailed Chemistry Approach the same conditions were reproduced. Special attention is paid on the analysis of the events leading up to the auto-ignition, which was reasonably well predicted.

This project is an experimental investigation and optimization of piston slap noise in small two-stroke gasoline engine. Piston slap is one of the most significant mechanical noise sources in an internal combustion engine. It is a dynamic impact phenomenon between the piston and the cylinder block caused by changes in the lateral forces acting on the piston. The change in cylinder block vibration level caused by the piston impact is considered as a measure of piston slap during this experiment. The intensity of piston slap is measured in terms of vibration level in ‘g’ units, by means of accelerometers mounted on the cylinder block with Top Dead Center (TDC) and Bottom Dead Center (BDC) marker. For the design of low noise engines, all the major parameters, which contribute to piston slap, are listed and the critical four are examined through additional experiments.

Recently the analysis of air-fuel mixing and combustion has become important under the stringent emissions regulations of diesel engines. In the case of gasoline engines, the KIVA computer program has been developed and used for the analysis of combustion. In this paper, the calculations of combustion phenomena in DI diesel engines are performed by modifying the KIVA program so as to be applicable to multi-hole nozzles and arbitrary patterns of injection rate. The thermophysical and ther-mochemical properties of gasoline are altered to those diesel fuel. In order to investigate the ability of this modified program, the calculations are compared with the experiments on single cylinder engines concerning the pressure, flame temperature and mass change of chemical species in cylinders. Furthermore, the calculation for the heavy duty DI diesel engine is performed with this diesel combustion program.

Renewable fuels, such as bio- and e-fuels, are of great interest for the defossilization of the transport sector. Among these fuels, methanol represents a promising candidate for emission reduction and efficiency increase due to its very high knock resistance and its production pathway as e-fuel. In general, reliable simulation tools are mandatory for evaluating a specific fuel potential and optimizing combustion systems. In this work, a previously presented methodology (Esposito et al., Energies, 2020) has been refined and applied to a different engine and different fuels. Experimental data measured with a single cylinder engine (SCE) are used to validate RANS 3D-CFD simulations of gaseous engine-out emissions. The RANS 3D-CFD model has been used for operation with a toluene reference fuel (TRF) gasoline surrogate and methanol. Varying operating conditions with exhaust gas recirculation (EGR) and air dilution are considered for the two fuels.

4 different engine concepts with Catalyst have been developed in regard to pollutant emission, fuel efficiency and performance. Despite the wide power range from 1,2 HP to 12 HP and the different applications of these engines to Mopeds, Chainsaws and Motorcycles, the problems to solve have been similar. Internal measures such as optimized carburetion, cooling, piston shape and clearance, scavenging and tuning of the exhaust must enable the engine to run on the lean side. This is imperative to supply sufficient oxygen for the exothermal reaction and to keep the energy to be converted in the Oxidation Catalyst at a minimum. Secondary measures have been taken to shorten the Catalyst's light-off and to keep the temperature range in limits.

There is a movement to apply emission control in a marine engine as well due to high public awareness of environmental concern in the United States. We started at the development of 3-seater Personal Watercraft (PWC) equipped with 4-stroke engines in taking environment conformity and potential into account. The PWC employed series 4-cylinder 1100cc displacement engine that has been used for mass production motorcycles. The engine was modified to satisfy requirements for PWC, as a marine engine, such as performance function and corrosion. In order to achieve greater or equal power/weight ratio as against two-stroke PWCs, a four-stroke engine for PWC with an exhaust turbo charger was developed. As a result, we succeeded in developing an engine that attained top-level running performance and durability superior to competitors' 2-stroke engines.

Since 1998, outboard motor manufactures are making every effort to meet the regulatory requirements that restrict the exhaust emissions from marine engines. Industry's first and the largest 4-sroke outboard motor F225A was introduced in the spring, 2001, targeting at off-shore fishing market in the U.S. This report describes technical features of 225HP V6 four-stroke outboard motor, which successfully conforms to the required limits, while maintaining the operating performance and compactness comparable to the corresponding two-stroke model, which has traditionally been in the mainstream of this marine engine segment.

TCT - Total Combustion Technology is technology designed to enable small SI four-stroke and two-stroke engines to meet current and proposed emission standards that pertain to small engines. This paper outlines the technology, the testing equipment, and the results from tests comparing TCT to original carburetors on two different engines. The comparison shows clearly that emissions can be reduced substantially by TCT. The MLC (Mechanical Lambda Control) feature of TCT allows the emission profile of the engine to be matched to the application in each case.

The quality of mixture formation and the combustion process is of significant importance for reducing the hydrocarbon emissions of small two stroke engines. The scope of this work was to investigate the mixture conditions after the exhaust closes and after the end of combustion depending on various engine operating points. For this experimental investigation a Gas Sampling Valve (GSV) was combined with a flame ionisation detector (FID) and a CO2-analyser. Using this technique, it was possible to measure the hydrocarbon concentration after end of combustion. Furthermore the local residual gas concentration after exhaust closes was determined. To allow for a comparison of the experimental results with calculations with CFD codes, in cylinder pressure measurement and exhaust gas measurements are done additionally.

In regard to small utility engines used in lawn and garden equipment and other commercial or industrial equipment, exhaust emission regulations have been implemented since 1995 in USA. In the State of California, USA, California Air Resources Board (CARB) Tier 2 emission regulations became effective from 2000. At this stage, the handheld engines are almost two-stroke engines, but this Tier 2 emission regulations are very stringent for HC emissions. In addition, the handheld engines are small, and so they do not have enough muffler volume to be equipped with larger catalysts. This paper describes the newly developed catalyst for two-stroke small engines, which is compact and excellent in HC conversion, to meet above requirements.

This paper presents the results of experiments conducted with a two-stroke engine that was the world's first such engine to comply with the emissions regulations applied to small off-road engines by the U.S. state of California in 2000. This engine is fitted with a scavenging passage that runs around the crankcase before the scavenging port. The aim of this research was to investigate how changes in the quantity of heat transferred to the fresh air as a result of varying the length of the scavenging passage would affect the state of combustion and exhaust gas composition. An ion probe was fitted to the end zone of the combustion chamber in order to detect the state of combustion. A voltage of 60 V was applied to the ion probe and measurements were made of the voltage drop that occurred due to the presence of high concentrations of ions (H3O+, C3H3+, CHO+, etc.) at the flame front.