Search Results

Fuel-borne catalysts are now an accepted means of aiding the self-regeneration of diesel particulate filters (DPFs). In the past it has been possible to assess the effect of these fuel additives by investigating the temperature at which the filter reaches a pressure drop equilibrium. Under these temperature conditions, the particulate matter is oxidised at the same rate as it is being deposited and there is thus no change in pressure drop across the filter. This technique adequately demonstrates the oxidation temperature of the carbon in the presence of the catalyst. However, it is now well known that such fuel additives also influence the low temperature oxidation of particulate bound hydrocarbons. This phenomenon is not detected by the filter equilibrium technique.

A novel dosing system for fuel borne catalyst (FBC), used to assist regeneration with a diesel particulate filter (DPF), has been developed. The system was designed for on-board vehicle use to overcome problems encountered with batch dosing systems. Important design features were simplicity, to minimise system cost, and the use of in-line dosing rather than batch dosing linked to tank refuelling. The paper describes the development of the dosing system which continuously doses FBC into the fuel line feeding the engine injection pump. The theoretical considerations behind the concept are explored, together with the realities imposed by fuelling regimes in which a variable proportion of the fuel flowing through the injection pump is passed back to the fuel tank. Two types of system are considered, ie where 1) FBC is added to the fuel in direct proportion to the flow rate of fuel and 2) FBC is added at a constant time-based rate.

Diesel particulate filter (DPF) are well known as a developing form of exhaust after-treatment for compression ignition engines. Subjected to extensive testing in experimental form, DPFs have yet to achieve widespread application in regular use on production road vehicles, despite their potential for delivering reductions of typically 90% in diesel exhaust particulate emissions. Tests have shown that different additives are effective in enhancing performance in a range of DPF types, and on engines of different configurations. Efforts have been made to correlate performance with engine operating regime, by linking soot particulate condition to the frequency of regeneration. A performance index has been developed to try to predict regeneration characteristics with additive treated fuel. The work has shown that there are engine operating conditions producing soot which is less likely to burn off in the DPF.

The earlier editions of this title have been best-selling definitive references for those needing technical information about automotive fuels. This long-awaited latest edition has been thoroughly revised and updated, yet retains the original fundamental fuels information that readers find so useful. This book is written for those with an interest in or a need to understand automotive fuels. Because automotive fuels can no longer be developed in isolation from the engines that will convert the fuel into the power necessary to drive our automobiles, knowledge of automotive fuels will also be essential to those working with automotive engines. Small quantities of fuel additives increasingly play an important role in bridging the gap that often exists between fuel that can easily be produced and fuel that is needed by the ever-more sophisticated automotive engine.

The first two editions of this title, published by SAE International in 1990 and 1995, have been best-selling definitive references for those needing technical information about automotive fuels. This long-awaited new edition has been thoroughly revised and updated, yet retains the original fundamental fuels information that readers find so useful. This book is written for those with an interest in or a need to understand automotive fuels. Because automotive fuels can no longer be developed in isolation from the engines that will convert the fuel into the power necessary to drive our automobiles, knowledge of automotive fuels will also be essential to those working with automotive engines. Small quantities of fuel additives increasingly play an important role in bridging the gap that often exists between fuel that can easily be produced and fuel that is needed by the ever-more sophisticated automotive engine.

In view of increasing concern over diesel particulates and tightening legislation to control their emission, much work has been done to develop diesel particulate filters (DPFs) and systems to allow them to work reliably. Although a filter will effectively trap solid particles, any material in the vapour phase, such as unburned hydrocarbons, may pass through the filter and subsequently condense. The use of a catalytic wash coat, either on the DPF itself or on a separate substrate, has been proposed to oxidise these hydrocarbons and thus reduce the total material emitted. The use of fuel borne catalysts to aid the regeneration of trapped material within the DPF is also well documented. Such catalyst will also catalyse the oxidation of any hydrocarbons bound up within the particulate. The oxidation of such hydrocarbon occurs at a lower temperature than that of carbon itself, thus allowing lower temperature regeneration of the DPF.

The most cost-effective way to reduce the level of diesel particulate emissions is to retrofit exhaust aftertreatment devices. While diesel oxidation catalysts will reduce the mass of particles emitted, they will not significantly reduce the number of ultrafine particles, that are considered the most harmful to health. Diesel Particulate Filters (DPFs) are therefore considered the most effective retrofit devices. One obstacle to the widespread adoption of DPFs is that many DPF technologies require low sulphur fuel. Using a Fuel Borne Catalyst (FBC) to facilitate regeneration of the DPF allows a sulphur tolerant DPF system to be produced.

There is mounting worldwide concern over the health effects of airborne ultra-fine particles. Of greatest concern are the risks due to the cancer-inducing properties of these particles and the aggravation of existing respiratory diseases by the ultra-fine (i.e. <2.5 micron) fraction. This disquiet has already resulted in legislation, regulations and other measures, either mandated or proposed, in the industrialised world to severely restrict particulate emissions from diesel-fuelled automotive transport. Emissions of particles from both new and existing vehicles have been addressed. With the rapid growth anticipated in some developing countries they to will need to address this problem. This paper outlines some alternative solutions to the problem, ranging from alternative power sources, alternative fuels, alternative engine technologies and after-treatment strategies. It also outlines what is required to implement these different solutions.

In the quest for improved fuel efficiency and reduced CO2 emissions, motor manufacturers are increasingly turning to the High Speed Direct Injection (HSDI) diesel engine for passenger car use. To achieve acceptable levels of noise and emissions at low loads two stage injection is being utilised. Such injection systems are prone to nozzle coking due to the small fuel metering holes, low opening pressures and low fuel flow rates under part load operation. This coking leads to a rapid deterioration of emissions performance. This paper describes work done to investigate conditions leading to this phenomena and the possible mechanisms involved.

Interest has been growing in many countries in the potential use of diesel particulate filters (DPF). This type of after treatment technology has been shown to make very significant reductions in both the mass of particulate emitted in diesel exhaust gas, and also in the number of fine particulates, which have been linked in recent years with concerns for human health. Work carried out during a development programme investigating the capability of fuel soluble metallic additives to assist DPF regeneration, indicated superior performance from a novel combination of metals in fuel soluble form. Earlier work showed that a fuel soluble combination of organo-metallic additives based on sodium and strontium gave very effective regeneration characteristics, and was capable of burning out carbon at temperatures from about 160°C.

Recent developments in diesel engines and fuel injection equipment together with the move to ULSD and bio-blends have seen an increase in reports regarding deposits in both injectors and filters. Historically deposits have been generated from a number of sources: bio-contamination, both aerobic and non-aerobic, water contamination, lube oil adulteration, additives, dirt, metals in fuel, and biodiesel degradation. These may be ascribed to “poor housekeeping,” incorrect additivation, deliberate adulteration or some combination. However the recently observed deposits differ from these. The deposits are described and indicate possible precursor molecules that support proposed mechanisms and their ability to form filter deposits.

Current developments in fuels and emissions regulations are resulting in an increasingly severe operating environment for diesel fuel injection systems. The formation of deposits within the holes or on the outside of the injector nozzle can affect the overall system performance. The rate of deposit formation is affected by a number of parameters, including operating conditions and fuel composition. For the work reported here an accelerated test procedure was developed to evaluate the relative importance of some of these parameters in a high pressure common rail fuel injection system. The resulting methodology produced measurable deposits in a custom-made injector nozzle on a single-cylinder engine. The results indicate that fuels containing 30%v/v and 100% Fatty Acid Methyl Ester (FAME) that does not meet EN 14214 produced more deposit than an EN590 petroleum diesel fuel.

Exhaust emissions legislation for diesel engines generally limits only the mass of emitted particulate matter. This limitation reflects the concerns and measurement technology at the time the legislation was drafted. However, evolving diesel particulate filter (DPF) systems offer the potential for reductions in the mass and more importantly, the number of particles emitted from diesel exhausts. Particulate filters require frequent cleaning or regeneration of accumulated soot, if the engine is to continue to operate satisfactorily. Exothermic reactions during regeneration can lead to severe thermal gradients in the filter system resulting in damage. Fuel additives have been evaluated to show significant reductions in light off temperature which allow frequent small regeneration events to occur, under mild operating conditions.

Recent developments in diesel engines and fuel injection equipment combined with the change to ULSD and bio-blends have resulted in increased reports regarding deposits within injectors and filters. A review of known fuel degradation mechanisms and other relevant chemistries suggests the effects of high pressure and high shear environments should be examined as the most probable causes of increasing deposit formation. Existing fuel quality tests do not correlate with reported fouling propensity. Analytical studies have shown that there are only subtle chemical changes for the materials within the standard diesel boiling range. The implications for further scientific study are discussed.

Continuing research into the effect of vehicle emissions is driving legislation, which is increasingly being enacted to encourage the retrofitting of emissions control devices. Of particular concern are emissions of diesel particulate matter and nitrogen oxides. More recently the adverse effects of nitrogen dioxide in particular, have been highlighted. A programme of work is underway in Santiago to demonstrate the suitability of retrofitting diesel particulate filters (DPF) to urban buses. This paper presents data, including regulated and unregulated emissions, from a bus fitted with a DPF that relies on a fuel borne catalyst (FBC) to facilitate regeneration of the DPF.

A dosing system has been developed to facilitate the addition of a fuel borne catalyst (FBC) to a vehicle's fuel supply. The on-board dosing system was primarily designed to reduce cost and complexity. One embodiment of the design provided an additional benefit, namely the automatic adjustment of treat rate according to duty cycle. For high duty operating cycles where average exhaust gas temperatures are high, a low treat rate of FBC is supplied. Conversely at low duty where the exhaust temperature is lower, a higher treat of FBC is delivered. Data from field applications are presented to demonstrate this feature.

The fuel injection equipment (FIE) has always been paramount to the performance of the Diesel engine. Increasingly stringent emissions regulations have dictated that the FIE becomes more precise and sophisticated. The latest generation FIE is therefore less tolerant to deposit formation than its less finely engineered predecessors. However, the latest emissions regulations make it increasingly difficult for engine manufacturers to comply without the use of exhaust aftertreatment. This aftertreatment often relies on catalytic processes that can be impaired by non-CHON (carbon, hydrogen, oxygen and nitrogen) components within the fuel. Fuel producers have therefore also been obliged to make major changes to try and ensure that with the latest technology engines and aftertreatment systems the fuel is still fit for purpose. However, there has recently been a significant increase in the incidence of reported problems due to deposit build-up within vehicle fuel systems.