Search Results

Parameters like brake mean effective pressure, mean velocity of the piston, hardness of the wear surface, oil film thickness, and surface areas of critical wear parts are similar for all the diesel engines. The mean piston velocity at the rated speed is nearly the same for all the diesel engines. The mechanical efficiency normalized to an arbitrary brake mean effective pressure (bmep) is dependent on the size of the engine. The engine life seems to be proportional directly to the square of a characteristic dimension namely, cylinder bore of the engine and inversely to speed and load factor for engines varying widely in sizes and ratings.

Abstract Turbocharging can provide a low cost means for increasing the power output and fuel economy of an internal combustion engine. Currently, turbocharging is common in multi-cylinder engines, but due to the inconsistent nature of intake air flow, it is not commonly used in single-cylinder engines. In this article, we propose a novel method for turbocharging single-cylinder, four-stroke engines. Our method adds an air capacitor-an additional volume in series with the intake manifold, between the turbocharger compressor and the engine intake-to buffer the output from the turbocharger compressor and deliver pressurized air during the intake stroke. We analyzed the theoretical feasibility of air capacitor-based turbocharging for a single-cylinder engine, focusing on fill time, optimal volume, density gain, and thermal effects due to adiabatic compression of the intake air.

An experimental methodology is proposed to measure the rollover propensity of road tankers when subjected to lateral perturbations derived from steering manoeuvers. The testing principle involves subjecting a scaled down sprung tank to the elimination of a lateral acceleration, to analyze its rollover propensity as a function of various vehicle's operational and design parameters. Initial acceleration is generated through putting the scaled tank on a tilt table supported by a hydraulic piston. The controlled release of the fluid in the hydraulic system generates a perturbation situation for the tank, similar to the one that a vehicle experiences when leaving a curved section of the road and going to a straight segment. Durations for the maneuver and initial tilt angles characterize both the corresponding intensities of the steering maneuver.

Abstract Three-dimensional patterns representing crosshatched plateau-honed cylinder bores based on two-dimensional Fast Fourier Transform (FFT) of measured surfaces were generated and used to calculate pressure flow, shear-driven flow, and shear stress factors. Later, the flow and shear stress factors obtained by numerical simulations for various surface patterns were used to calculate lubricant film thickness and friction force between piston ring and cylinder bore contact in typical diesel engine conditions using a mixed lubrication model. The effects of various crosshatch honing angles, such as 30°, 45°, and 60°, and texture heights on engine friction losses, wear, and oil consumption were discussed in detail. It is observed from numerical results that lower lubricant film thickness values are generated with higher honing angles, particularly in mixed lubrication regime where lubricant film thickness is close to the roughness level, mainly due to lower resistance to pressure flow.

To reduce heat transfer between hot gas and cavity wall, thin Zirconia (ZrO2) layer (0.5mm) on the cavity surface of a forged steel piston was firstly formed by thermal spray coating aiming higher surface temperature swing precisely synchronized with flame temperature near the wall resulting in the reduction of temperature difference. However, no apparent difference in the heat loss was analyzed. To find out the reason why the heat loss was not so improved, direct observation of flame impingement to the cavity wall was carried out with the top view visualization technique, for which one of the exhaust valves was modified to a sapphire window. Local flame behavior very close to the wall was compared by macrophotography. Numerical analysis by utilizing a three-dimensional simulation was also carried out to investigate the effect of several parameters on the heat transfer coefficient.

The design and development of a new four-stroke two-cylinder diesel engine family of 1.29 litre capacity for off road are discussed. The engine is in naturally aspirated and turbocharged and intercooled versions and rated from 11.9 kW/1500 rpm to 25.7 kW/2500 rpm. The engines were tuned for air and fuel flows, air utilisation, fuel air mixing, performance and emissions at steady state at a development lab and later certified in national labs. The high altitude capability of the TCIC was checked using a model. The engines rated at less than 19 kW satisfy India Generator set and off road norms of India and Europe equivalent to USTier4 standard, and at higher ratings, standard equivalent to US Tier4-interim. In the second part of the paper, the design of coolant and oil pumps, oil cooler for TCIC engine and the piston with steel oil control ring are discussed. The higher loaded TCIC engines use fillet hardened crankshafts of chromium molybdenum steel.

The objective of this study was to evaluate iso-butanol (C4H9OH) as an alternative fuel for spark ignition engines. Unlike methanol (CH3OH) and ethanol (C2H5OH), iso-butanol has not been extensively studied in the past as either a fuel blend candidate with gasoline or straight fuel. The performance of a single cylinder engine (ASTM=CFR) was studied using alcohol-gasoline blends under different input parameters. The engine operating conditions were: three carburetor settings (three different fuel flow rates), spark timings of 5°, 10°, 15°, 20°, and 25° BTDC, and a range of compression ratios from a minimum of 7.5 to a maximum of 15 in steps of one depending on knock. The fuels tested were alcohol-gasoline blends having 5%, 10%, 15%, and 20% of iso-butanol, ethanol, and methanol. And also as a baseline fuel, pure gasoline (93 ON) was used. The engine was run at a constant speed of 800 RPM.

The reduction of friction losses is a subject of central importance in a diesel engine. The piston frictions of low viscosity engine oil and molybdenum dialkyl dithiocarbamate (MoDTC) have been measured by floating liner method. It was found that the low viscosity engine oil lower than 5W-30 is not effective against the reduction of friction mean effective pressure (FMEP) related to the fuel consumption. MoDTC showed a good performance against the reduction of FMEP. In the friction measurement points, the reduction ratio of 10W-30 with MoDTC to 10W-30 was greater than that of 5W-30 to 10W-30.

A high-speed photographic study is presented illustrating the influence of engine variables such as an introduced air swirl, the number of nozzle holes and the piston cavity diameter, on the combustion process in a small direct-injection (D.I.) diesel engine. The engine was modified for optical access from the under and lateral sides of the combustion chamber. This modification enabled a three-dimensional analysis of the flame motion in the engine. The swirling velocity of a flame in a combustion chamber was highest in the piston cavity, and outside the piston cavity it became lower at the piston top and at the cylinder head in that order. The swirl ratio of the flame inside the cavity radius attenuated gradually with piston descent and approached the swirl ratio outside the cavity radius, which remained approximately constant during the expansion stroke. Engine performance was improved by retarding the attenuation of the swirl motion inside the cavity radius.

Utilizing an opportunity presented by a mountain-road construction-project in California, eight Class-B 3½-ton trucks were assigned to the work and a test of air-cleaners was conducted during its progress. Six trucks were each equipped with an air-cleaner; two were not. The trucks had dump-bodies and were specially prepared for the test, details of this preparation being specified. Due to varied air-cleaner design, it was not feasible to locate the cleaners identically on all the trucks, and differences in mounting may have influenced the resulting air-cleaner efficiency, but mountings were made as nearly identical as possible. Tables of average wear of piston-rings, engine cylinders and crankpins, for 1000 hr. of use, are presented, and details of how the measurements were made are stated, together with a discussion of the “growth” of pistons and of the peculiarities of wear.

This SAE Recommended Practice is intended to describe a procedure for rating the size of single-stage reciprocating air compressors. It describes the conditions that can be used for testing and it defines a standardized rating expressed in SLPM (SCFM).

This SAE Recommended Practice is intended to describe a procedure for rating the size of single-stage reciprocating air compressors. It describes the conditions that can be used for testing and it defines a standardized rating expressed in SLPM (SCFM).

This paper studies the nonlinear characteristics of air suspension. The air spring's nonlinear model by the internal volume variation due to the compression of the spring and the variation of effective area pressure acts on is established. The comparison of simulation and experiment indicates the validity of the model in the paper. The characteristics of a quarter vehicle model with the air spring model presented in the paper have been studied. This analysis can guide the design of the air spring's shape and the piston contour, and understand the performances and the effects of air spring in vehicle.

Radial piston units find several applications in fluid power, offering benefits of low noise and high power density. The capability to generate high pressures makes radial piston pumps suitable for clamping function in machine tools and also to operate presses for sheet metal forming. This study is aimed at developing a comprehensive multidomain simulation tool to model the operation of a rotating cam type radial piston pump, with particular reference to the lubricating gap flow between the pistons and the cylinder block. The model consists of a first module which simulates the main flow through the unit according to a lumped parameter approach. This module evaluates the features of the displacing action accounting for the detailed evaluation of the machine kinematics and for the mechanical dynamics of the check valves used to control the timing for the connection of each piston chamber with the inlet and outlet port.

Impingement of a spray flame on the periphery of the piston cavity strongly affects heat loss to the wall. The heat release rate history is also closely correlated with the indicated thermal efficiency. For further thermal efficiency improvement, it is thus necessary to understand such phenomena in state of the art diesel engines, by observation of the actual behavior of an impinging spray flame and measurement of the local temperature and flow velocity. A top-view optically accessible engine system, for which flame impingement to the cavity wall can be observed from the top (vertically), was equipped with a high speed digital camera for direct observation. Once the flame impinged on the wall, flame tip temperature decreased roughly 100K, compared to the temperature before impingement.

It is known that the mass flow rate through poppet valves of 4-stroke cycle engines and through piston valves of 2-stroke cycle engines decrease with increase in engine speed. In this paper, a disc-type rotary valve was used to experimentally analyze the decrease in flow rate at high rotational speeds and to determine what variables, other than rotational speed, give rise to the observed behaviour. These variables have been included in an empirical equation which is representative of the measured flow characteristics.

Abstract Direct dual fuel stratification (DDFS) strategy benefits the advantages of the RCCI and PPC strategies simultaneously. DDFS has improved control over the heat release rate, by injecting a considerable amount of fuel near TDC, compared to RCCI. In addition, the third injection (near TDC) is diffusion-limited. Consequently, piston bowl geometry directly affects the formation of emissions. The modified piston geometry was developed and optimized for RCCI by previous scholars. Since all DDFS experimental tests were performed with the modified piston profile, the other piston profiles need to be investigated for this strategy. In this article, first, a comparative study between the three conventional piston profiles, including the modified, stock, and scaled pistons, was performed. Afterward, the gasoline injector position was shifted to the head cylinder center for the stock piston. NOX emissions were improved; however, soot was increased slightly.

The novel wave-shaped bowl piston geometry design with protrusions has been proved in previous studies to enhance late-cycle mixing and therefore significantly reduce soot emissions and increase engine thermodynamic efficiency. The wave-shaped piston is characterized by the introduction of evenly spaced protrusions around the inner wall of the bowl, with a matching number with the number of injection holes, i.e., flames. The interactions between adjacent flames strongly affect the in-cylinder flow and the wave shape is designed to guide the near-wall flow. The flow re-circulation produces a radial mixing zone (RMZ) that extends towards the center of the piston bowl, where unused air is available for oxidation promotion. The waves enhance the flow re-circulation and thus increase the mixing intensity of the RMZ.

The objective of this paper is to present the results of an investigation of elastic distortions of split piston rings that are used in lubricated and non-lubricated air brake compressors. Concepts of advanced stress analysis and Finite Element Analysis (FEA) have been employed in this study. The analysis of elastic distortions (twist) of piston rings due to the installation stresses has been quite poorly documented in the technical literature. As a result, unjustifiable engineering assumptions are some time made which result in misleading design solutions. This paper demonstrates analytically and with the support of FEA the mechanical/geometrical parameters of a split ring which affect the twist of the ring during the installation in the cylinder bore, and the calculated magnitude of this twist along the ring circumference.

An ongoing research and development activities on the scavenged pre-chamber ignition system for an automotive natural gas fueled engine is presented in this paper. The experimental works have been performed in engine laboratory at steady state conditions on a gas engine with 102 mm bore and 120 mm stroke, converted to a single cylinder engine. The in-house designed scavenged pre-chamber is equipped with a spark plug, fuel supply and a miniature pressure sensor for detailed combustion diagnostics. The engine was operated at constant speed, fully open throttle valve and four different fueling modes with or without spark discharge. A partly motored mode allowed direct evaluation of the pre-chamber heat release. The experimental data acquired in this research served as a validation data for the numerical simulations. The performed tests of prototypes and calculations have recently been expanded to include 3-D flow calculations in the Ansys Fluent software.