Search Results

This paper summarizes the techniques and guidelines which were used to reduce the driver perceived noise level of a 145-210 HP series of agricultural tractors. Graphs of case study test results and comments on subjective noise quality are provided to guide the acoustic novice through the complexities of the vehicle sound environment in a methodical problem solving format.

Contact the appropriate representative of the 2023 Noise and Vibration Conference and Exhibition.

Health related problems in over populated areas are a major concern and as such, there are specific legislations for noise generated by transport vehicles. In diesel powered commercial vehicles, the source for noise are mainly related to rolling, transmission, aerodynamics and engine. Considering internal combustion engine, three factors can be highlighted as major noise source: combustion, mechanical and tailpipe. The tailpipe noise is considered as the noise radiated from the open terminations of intake and exhaust systems, caused by both pressure pulses propagating to the open ends of the duct systems, and by vortex shedding as the burst leaves the tailpipe (flow generated noise). In order to reduce noise generated by vehicles, it is important to investigate the gas interactions and what can be improved in exhaust line design during the product development phase.

The new 5480 Reach Truck, designed at Dynamic Industries, introduces a movable frame between the main frame and the telescopic boom. The use of this movable frame allows the usually fixed boom pivot to be elevated for greater lifting heights with smaller boom sections. By combining the motions of the boom and the movable frame, horizontal motion at the boom tip is possible without moving the truck. With the movable frame, the total machine height and length can be reduced for a given lifting goal. Another advantage of the movable frame is the ability to reach further below grade than is now possible in the industry. The 5480 Reach Truck has a maximum lift of 54 feet (16.5 meters) and can reach 24 feet (7.3 meters) below-grade.

The model 753 skid steer loader was developed to address performance, service and manufacturing issues for the company's 1300 lb. class loader and to provide exciting new features for marketing. This paper describes many of the improvements and features that will accentuate the Bobcat skid steer loader family in the nineties.

The LTL-900 Transi-Lift crane features front and rear crawler-mounted load platforms connected with a hoist-supporting five foot diameter pipe section. The pin-together main boom is available in lengths up to 400 feet and completely disassembles for ease of transport to and from the jobsite. The crane requires three operators and can hoist, boom, swing and travel simultaneously with maximum loads. Upending, moving and setting large refinery vessels is facilitated by the mobility of the crawler-supported crane on unprepared surfaces. Up to 1000 tons of 36 ton concrete beams or equivalent are required as counterweight to develop the ANSI B30.5 approved capacities.

A unique shuttle bus is being constructed by Minicars, Inc., and Walter Vetter Karosserie-werk for Denver’s Transitway/Mall. The bus is designed for frequent stop, low speed service in a downtown pedestrian environment. It features a very low floor and multiple wide doors for rapid passenger boarding and deboarding. Two versions will be supplied for comparative evalation, a low noise diesel configuration and a battery-electric configuration. Either version can subsequently be converted to the alternative propulsion system.

The paper addresses some aspects of an ongoing research on a commercial compact excavator. The interest is focused on the analysis and modelling of the whole hydraulic circuit that, beside a load sensing variable displacement pump, features a stack of nine proportional directional control valves modules of which seven are of the load sensing type. Loads being sensed are the boom swing, boom, stick and bucket, right and left track motors and work tools; instead, the blade and the turret swing users do not contribute to the load sensing signal. Of specific interest are the peculiarities that were observed in the stack. In fact, to develop an accurate AMESim modelling, the stack was dismantled and all modules analysed and represented in a CAD environment as 3D parts. The load sensing flow generation unit was replaced on the vehicle by another one whose analysis and modelling have been developed using available design and experimental data.

This paper outlines what a large company is doing on a corporate staff basis to help combat Product Liability problems. Eaton Corporation is multi-national and serves a variety of markets. The extensive and complex line of products dictates the need for a well organized, corporate Product Assurance Program. The program is made up of five thrusts: 1) Corporate Policy, 2) Guidelines, 3) Divisional Committees, 4) Surveys and 5) Training. Utilizing a product development project, the implementation of several elements of Product Quality Assurance are explained. The program was designed for flexibility and emphasizes the chairman's motto to “DO IT RIGHT THE FIRST TIME, EVERY TIME.”

A Decision Network is an explicit model of the Thinking Breakdown Structure of any complex scientific, engineering, or societal challenge. Each node in the Decision Network represents a fundamental question that must be answered, i.e. a choice that demands a solution. A Decision Network provides an integrated Decision Management framework for any Systems Engineering effort that links business, technology and design choices. Effective Decision Management is the key to Systems Engineering success. This paper will provide an overview of a decision-centric approach to Systems Engineering built around Decision Networks. Lessons learned through the use of Decision Networks in other industries will be extrapolated for use in vehicle Systems Engineering.

The need for a foreshortened product development lead time has become a necessity, in today's economy, to the efficient manufacturing of off-highway mining trucks. This paper reviews the approach taken by one noted truck manufacturer. By utilizing finite element analysis, plastic scale modeling techniques, and a comprehensive full scale test facility, the development lead time of the WABCO 100 Ton HAULPAK* was reduced to 60% of that normally required for the development of a new product from conceptual layout to production release.

A distributed sensor is created to sense the rate of change in deflection of beam-like structures such as crane booms. This sensor will be useful in electrohydraulic compensation of boom deflections. The sensor is made of an array of strain-sensitive segments such as strain gages or piezoelectric film. In this example, segments of piezoelectric film convert strains on the surface of a vibrating beam into electrical outputs. These outputs are connected to low impedance signal conditioners. The output of the signal conditioners are then interpolated with a weighting vector that incorporates Lagrange polynomials, specified boundary conditions, and the desired location(s) of measurement. A simple linear combiner circuit combines the electrical outputs into the deflection velocity at the desired points.

As we move toward electrification in future mobility, weight and cost reduction continue to be priorities in vehicle development. This has led to continued interest in advanced molding processes and holistic design to enable polymer materials for demanding structural applications such as pickup truck beds. In addition to performance, it is necessary to continue to improve styling, functionality, quality, and sustainability to exceed customer expectations in a competitive market. To support development of a lightweight truck bed design, a cross-functional team objectively explored the latest materials and manufacturing technologies relevant to this application. In Phase 1 of this work, the team considered a variety of alternatives for each functional area of the bed, including thermoplastic and thermoset materials with a range of processing technologies.

The transition from ICE to electric power trains in new vehicles along with the application of advanced active and passive noise reduction solutions has intensified the perception of noise sources not directly linked to the propulsion system. This includes road noise as amplified by the tire cavity resonance. This resonance mainly depends on tire geometry, air temperature inside the tire and vehicle speed and is increasingly audible for larger wheels and heavier vehicles, as they are typical for current electrical SUV designs. Active technologies can be applied to significantly reduce narrow band tire cavity noise with low costs and minimal weight increase. Like ANC systems for ICE powertrains, they make use of the audio system in the vehicle. In this paper, a novel low-cost system for road induced tire cavity noise control (RTNC) is presented that reduces the tire cavity resonance noise inside a car cabin.

Rapid Urbanisation, in recent times, has created an exponential demand for light commercial vehicles. Electric vehicles are seen as a way to reduce the impact of emissions due to transportation in urban areas. Due to the growth of e-commerce, commercial transportation, and particularly last-mile delivery, is anticipated to increase. In this context, electric light commercial vehicles (eLCVs) have the potential to be a promising solution by tackling the emission impacts, ensuring faster delivery along with ideal running costs and payload capacity. To increase the range of electric vehicles, it has to be designed for lighter weight with optimal performance in order to meet the user requirements. Cargo capacity and payload have to be taken into account while design & validating the vehicle structure under static and dynamic conditions. Simulation driven product development will help the design team to account for the possible design failure cases at system and vehicle level.

In automotive design and development, there are different stages for product design. In this fast changing scenario product design, digital verification of design (CAE), physical validation of the product and launching of the same in short time is important in product development life cycle of any new generation vehicle. This paper proposes a new approach towards development of a green-field platform for commercial vehicles by improving reliability of CAE and thereby reducing the need for prototype testing and hence shortening development cycle and costs - we call it “Hybrid Mule”. This Hybrid Mule has complete design intent under-body and engine-house while upper-body is made of simple representative tubular space frame. FRP skin panels are attached to this space frame to create a safe environment for test-driver. FRP skin also provides early feel of styling in running condition and evaluates basic ergonomics and visibility.

A new method to predict brake squeal occurrence was developed by MSC under contract to Ford Motor Company. The results indicate that the stability characteristics of this disc brake assembly are governed mainly by the frictional properties between the pads and rotor. The stability is achieved when the friction coefficient of the pads is decreasing as the contact force increases. Based on the results, a stable brake system can be obtained without changing the brake structure by incorporating the appropriate frictional coefficient in the brake system. The method developed here can be also used as a tool to test the quality of any brake design in the early design stage.

The paper covers a new generation of manual transmissions for light and medium-duty trucks, vans and buses, initially introduced in a 5-speed version. The product reflects levels of driving comforts which are new to this class of vehicle worldwide with respect to shiftability, shift feel, noise emission, efficiency and durability.

In order to reduce high-frequency harmonic noise produced by the blower in the auxiliary system of a fuel cell vehicle (FCV), a narrowband active noise control (ANC) method instead of conventional passive mufflers is adopted since the blower demands clean air condition and expects good acoustic performance. However, in ANC practical applications, the frequency difference between reference signal and actual primary signal, i.e., frequency mismatch (FM), can significantly degrade the high-frequency performance of narrowband ANC system. In this paper, a new narrowband ANC system is proposed to compensate for the performance degeneration due to the existence of FM and improve noise reduction at high frequencies. The proposed system consists of two parts: the Filtered Error Least Mean Square (FELMS) algorithm filtering the primary signals at wide frequency range other than those at the targeted frequencies, and the FM removal algorithm proposed by Yegui Xiao.

A farm tractor protection cab made of thin steel sheet pressings is described. The cab is designed and produced using entirely automotive-type procedures. Curved glasses and a dampening suspension of the glasses are found to be an important means of achieving a low noise level in the cab. Using the pressing technique when producing a steel cab makes it possible to give the various cab details rigidity with a minimum of material. When welded together, these details form a very stiff cab body, which gives the necessary mechanical strength. The curved surfaces, the radii, and the round forms, which from a tooling point of view are natural for pressed steel parts, also have a vibration-dampening effect on the entire cab construction, thus making it easier to design a quiet tractor cab. Mounted on a farm tractor of conventional design, the cab meets the noise rating number ISO N85.