Search Results

This document is divided into five parts. The first part deals with flotation analysis features and definitions to acquaint the engineer with elements common to the various methods and the meanings of the terms used. The second part identifies and describes current flotation analysis methods. Due to the close relationship between flotation analysis and runway design, methods for the latter are also included in this document. As runway design criteria are occasionally used for flotation evaluation, including some for runways built to now obsolete criteria, a listing of the majority of these criteria constitutes the third part. The fourth part of this document tabulates the most relevant documents, categorizing them for commercial and civil versus military usage, by military service to be satisfied, and by type of pavement. This document concludes with brief elaborations of some concepts for broadening the analyst’s understanding of the subject.

This work covers the historical development of Built-In-Test (BIT) for fiber optic interconnect links for aerospace applications using Optical Time Domain Reflectometry (OTDR) equipped transceivers. The original failure modes found that installed fiber optic links must be disconnected before diagnosis could begin, often resulting in “no fault found” (NFF) designation. In fact, the observed root cause was that most (85%) of the fiber optic link defects were produced by contamination of the connector end faces. In March of 2006, a fiber optics workshop was held with roughly sixty experts from system and component manufacturers to discuss the difficulties of fiber optic test in aerospace platforms. During this meeting it was hypothesized that Optical Time Domain Reflectometry (OTDR) was feasible using an optical transceiver transmit pulse as a stimulus. The time delay and amplitude of received reflections would correlate with the position and severity of link defects, respectively.

Aircraft that carry crew and/or passengers must pass one or more icing-related standards for certification. Ice protection systems and components play a crucial role in safe aircraft operation. Such systems are usually installed in wings, nacelle intakes, pitot tubes, stabilizers, and propeller and helicopter rotor blades. These safety-critical systems follow a certification requirement per Code of Federal Regulations (CFR) part 23, 25, 27, 29, and others, for the various types of aircraft and rotorcraft as well as engines.

This interface standard applies to fuzes used in airborne weapons that use a 3-in fuze well. It defines: Physical envelope of the fuze well at the interface with the fuze. Load bearing surfaces of the fuze well. Physical envelope of the fuze and its connector. Mechanical features (e.g., clocking feature). Connector type, size, location and orientation. Retaining ring and its mechanical features (e.g., thread, tool interface). Physical envelope of the retaining ring at the interface with the fuze. Physical space available for installation tools. Torque that the installation tool shall be capable of providing. This standard does not address: Materials used or their properties. Protective finish. Physical environment of the weapon. Explosive interface or features (e.g., insensitive munitions (IM) mitigation). Charging tube. Torque on the retaining ring or loads on the load bearing surfaces.

SAE International is inviting global participation in its AeroTech® aerospace and defense technology conference and exhibition, which is for the first time co-located with ASM International’s AeroMat, at the Pasadena Convention Center in Pasadena, California, March 15 through 17, 2022.

This course is verified by Probitas Authentication as meeting the AS9104/3A requirements for continuing Professional Development. Why is a design for manufacturing, assembly and automation so important? This introductory course on airframe engineering will cover the importance of design for manufacturing, assembly and automation in aerospace. It will review what the key drivers are for a “good” design and some of the key points for manufacturing and assembly of aircraft components. It will look at how an engineer can combine traditional technologies with new, cutting-edge technologies, to determine the best scenario for success.

Quality management professionals across the global aerospace and defense community are convening for one hour – Wednesday, October 27th, starting at 10 am Pacific Daylight Time (PDT) – to discuss the AS9100 international standard. Register to take part in the free AeroTech webinar, hosted by SAE International and Tektronix, designed to help manufacturers, contractors, and subcontractors throughout the global aviation, space, and defense supply chain keep pace with and meet the requirements of AS9100 international quality management system standard.

This SAE Aerospace Standard (AS) establishes guidelines for the use of IEEE-1394-2008 Beta (formerly IEEE-1394b) as a data bus network in military and aerospace vehicles. It encompasses the data bus cable and its interface electronics for a system utilizing S400 over copper medium over extended lengths. This document contains extensions/restrictions to “off-the-shelf” IEEE-1394 standards, and assumes that the reader already has a working knowledge of IEEE-1394. This document does not identify specific environmental requirements (electromagnetic compatibility, temperature, vibration, etc.); such requirements will be vehicle-specific and even LRU-specific. However, the hardware requirements and examples contained herein do address many of the environmental conditions that military and aerospace vehicles may experience. One should refer to the appropriate sections of MIL-STD-461E for their particular LRU, and utilize handbooks such as MIL-HDBK-454A and MIL-HDBK-5400 for guidance.

Engineering Events staff at SAE International in Warrendale, Pennsylvania, have extended the call for abstracts through September 21 for the organization’s AeroTech aerospace and defense technology conference, which will take place at the Fort Worth Convention Center in Fort Worth, Texas, March 14-16, 2023. Visit the AeroTech call for abstracts page for more information and to get started.