Search Results

In the recent years diesel engine developers and manufacturers achieved a great progress in reducing the most important diesel engine pollutants, NOX and particulates. But nevertheless big efforts in diesel engine development are necessary to meet with the more stringent future emission regulations. To improve the knowledge about particle formation and emission an insight in the cylinder is necessary. By using the fast gas sampling technique samples from the cylinder were taken as a function of crank angle and analyzed regarding the soot particle size distribution and the particle mass. The particle size distribution was measured by a conventional SMPS. Under steady state conditions the influence of aromatic and oxygen content in the fuel on in-cylinder particle size distribution and particle mass inside a modern 4V-CR-DI-diesel-engine were determined. After injection and ignition, mainly small soot particles were formed which grow and in the later combustion phase coagulate.

Diesel fuels have been tested in both a naturally aspirated and an externally supercharged single cylinder, air cooled KHD DI-diesel engine, to determine the influence of poor fuel quality on combustion and emissions. A thermodynamic analysis of the cylinder pressure was conducted and the emissions were measured both gaseous as well as the particle emission (by means of a dilution tunnel). Additionally, extensive cold start tests were conducted. Under steady state conditions the cetane number seems to be a good parameter which describes the ignition behavior of different fuels. At low load, a change in combustion and a high increase in CO, HC and particle emissions were found with decreasing cetane number. During cold starting and warming up, a clear deterioration of the emission and combustion characteristics was also observed with decreasing cetane number when basic fuels were used.

This paper describes research and development activities dealing with a technique which allows the measurement of gaseous and particulate concentrations inside the combustion chamber. This so-called fast-timed gas sampling technique was used for both the observation of the development of gaseous pollutants and soot during combustion and expansion and for getting information about the particle size history. The system has been applied to a modern passenger car DI diesel engine (Volkswagen). The investigation covers the early combustion phase beginning with the start of combustion and throughout the expansion phase until exhaust valve opening. Particles with a size of about 10 nm up to 1 μm were found. Slight variations in the smaller size classes could be observed during the combustion and expansion process.

The European research co-operation Lotus is presented. The main objectives of the project were i) to show the potential for a urea-based SCR system to comply with the EU standard of years 2005 and 2008 for heavy-duty Diesel engines for different driving conditions with optimal fuel consumption, ii) to reach 95 % conversion of NOx at steady state at full load on a Euro III engine, iii) to reach 75 % NOx reduction for exhaust temperatures between 200-300°C, and 85 % average NOx reduction between 200-500°C. The energy content of the consumed urea should not exceed 1.0 %, calculated as specific fuel consumption. These targets were met in May 2003 and the Lotus SCR system fulfilled the Euro V NOx legislative objectives for year 2008.

The deposits on intake valve tulips of spark ignition and diesel engines can produce an increase in fuel consumption and exhaust gas emission, a deterioration of the driving behavior as well as mechanical defects. The formation of these deposits is investigated with respect to different engine parameters and by using a commercially available leaded fuel without additives. The valve deposits are formed by composing and decomposing phenomena which occur in parallel. The composing elements are oil, particles coming from the combustion chamber via the internal exhaust gas recirculation and, partially, fuel components. The deposits are reduced by the liquid fuel coming in contact with the valve tulips and by a high rate of oil flow. To the end of a shorter test duration and less test efforts a short-time simulation to investigate the deposit formation on inlet valves will be described.

During the lifetime of an internal combustion engine, deposits are formed at various locations. In diesel engines, deposits in the combustion chamber and at the injection nozzles lead to an increase in the emissions, especially the particulate emissions, and the exhaust gas odor. Additionally, durability problems can also arise. Deposits in the combustion chamber of SI engines can increase the octane requirement, deposits at intake valves can reduce engine efficiency and driveability and increase emissions. A detailed theory on the mechanism of deposit formation, considering the physical effects, is presented. This theory contains a deposit transport mechanism, a mechanism of deposit attachment including an induction phase, a deposit growth phase and a deposit removal mechanism. This complex theory is based on fundamental investigations at different locations in and around internal combustion engines.

A modular particulate trap system for buses, trucks and other applications consiting of honeycomb traps and an electrical regeneration system has been designed and tested on a test bench and in a city bus. For regeneration, the soot is ignited at the entrance of the trap channel by electric heaters. After ignition, the soot burns self-supporting without further energy supply. Regeneration is possible over the whole engine map. The electrical energy consumption of the heaters for a city bus is in average below 100 W. The filtration efficiency of the system including regeneration is about 80 % during transient city driving. During regeneration, appr. 98 % of the accumulated hydrocarbons adsobed to the soot in the trap are burned off the initiated combustion front. Additionally, the odor of the diesel engine exhaust gas behind the trap is lowered at low engine load even during regeneration.

Diesel soot collected in a catalytically coated ceramic honeycomb trap, burns self-supporting, if the heat loss is less than the heat release due to soot oxidation. Experimental verification has been accomplished using a 4.66″ × 6″, 100 CPI trap. Ignition time and regeneration time are measured. At low speeds, a minimum ignition time of 15 s would be sufficient for the trap regeneration. An extended channel with an observation window is provided to allow examination of the regeneration. The soot is ignited at the beginning of the channel and the flame propagation is then observed. The soot burns through the channel in a match-like manner. Manganese and iron fuel additives are observed to have an effect on the mechanism of flame propagation.