Search Results

This document describes requirements for standardized processes (and associated technologies) that ensure type design data are retrievable and usable for the life of a type certificate (50+ years). These processes are primarily concerned with, but not limited to, digital type design data retained in three-dimensional representations and associated data that is required for complete product definition, such as tolerances, specification call-outs, product structure and configuration control data, etc. This process standard includes process requirements for managing the evolution of technologies required to ensure the availability of the data for the life of the product. This data must be available to meet regulatory, legal, contractual and business requirements. This process standard is not intended to incorporate every company specific requirement and does not dictate specific organizational structures within a company.

This document describes requirements for standardized processes (and associated technologies) that ensure type design data are retrievable and usable for the life of a type certificate (50+ years). These processes are primarily concerned with, but not limited to, digital type design data retained in three-dimensional representations and associated data that is required for complete product definition, such as tolerances, specification call-outs, product structure and configuration control data, etc. This process standard includes process requirements for managing the evolution of technologies required to ensure the availability of the data for the life of the product. This data must be available to meet regulatory, legal, contractual and business requirements. This process standard is not intended to incorporate every company specific requirement and does not dictate specific organizational structures within a company.

This standard establishes the baseline requirements for performing and documenting FAI. Should there be a conflict between the requirements of this standard and applicable statutory or regulatory requirements, the applicable statutory or regulatory requirements shall take precedence.

This document contains recommended practices for the effective control of non-deliverable software. It addresses practices for control during the development, production, release maintenance, and retirement of non-deliverable software, as well as for software procured from outside manufacturers and incorporated in the production, evaluation, test, acceptance or calibration of processes. For the purposes of this document, the terms software and non-deliverable software are considered synonymous.

This document contains recommended practices for the effective control of non-deliverable software. It addresses practices for control during the development, production, release maintenance, and retirement of non-deliverable software, as well as for software procured from outside manufacturers and incorporated in the production, evaluation, test, acceptance or calibration of processes. For the purposes of this document, the terms software and non-deliverable software are considered synonymous.

This document contains recommended practices for the effective control of non-deliverable software. It addresses practices for control during the development, production, release maintenance, and retirement of non-deliverable software, as well as for software procured from outside manufacturers and incorporated in the production, evaluation, test, acceptance or calibration of processes. For the purposes of this document, the terms software and non-deliverable software are considered synonymous.

The aviation, space, and defense industries rely on the development and manufacture of complex products comprised of multiple systems, subsystems, and components each designed by individual designers (design activities) at various levels within the supply chain. Each design activity controls various aspects of the configuration and specifications related to the product. When a change to design information is requested or required, the change has to be evaluated against the impacts to the higher-level system. Proposed changes to design information that the design activity identifies to be minor and have no effect on their product requirements or specifications have the potential to be concurrently implemented and approved, where authorized to do so. Changes that affect customer mandated requirements or specifications shall be approved prior to implementation.

The aviation, space, and defense industries rely on the development and manufacture of complex products comprised of multiple systems, subsystems, and components each designed by individual designers (design activities) at various levels within the supply chain. Each design activity controls various aspects of the configuration and specifications related to the product. When a change to design information is requested or required, the change has to be evaluated against the impacts to the higher-level system. Proposed changes to design information that the design activity identifies to be minor and have no effect on their product requirements or specifications have the potential to be concurrently implemented and approved, where authorized to do so. Changes that affect customer mandated requirements or specifications shall be approved prior to implementation.

This standard is primarily intended to apply to new parts and products, but can also be applied to parts currently in production. The standard shall be applicable to all production processes, that influence the variation of KCs, as well as maintenance processes in which KCs are identified. It applies to assemblies and all levels of parts within an assembly, down to the basic materials including castings and forgings, and to organizations that are responsible for producing the design characteristics of the product. It does not apply to lab-scale, pilot, or pre-production processes. However, particular management of some KCs might be required using other methods than those described in the standard, during these phases of a program, when required by the customer or deemed appropriate by the organization (e.g., Engineering department requirement).

This standard is primarily intended to apply to new parts and products intended to be produced in an on-going production phase, but can also be applied to parts currently in production (e.g., manufacturing, maintenance). The standard is applicable to all production processes that influence the variation of KCs, as well as maintenance and service processes in which KCs are identified. It applies to organizations for assemblies and all levels of parts within an assembly, down to the basic materials including castings and forgings, and to organizations that are responsible for producing the design characteristics of the product. The variation control process begins with product definition, typically stated in the design documentation (e.g., digital model, engineering drawing, specification) which identifies KCs, and leads to a variation management process for those KCs. This process may also be used for producer-identified KCs (e.g., process KCs, additional/substitute product KCs).

This standard establishes requirements when implementing statistical product acceptance methods to meet defined risk requirements. This standard also establishes the minimum content required to be covered in an organization’s documented procedures that govern their application of statistical product acceptance methods. These general requirements and documented procedures apply the requirements of the 9100/9110/9120 quality management system standards, in addition to establishing requirements for retrievability, safety/critical characteristics, and quality parameters that protect the customer.

The objective of any organization, as part of continual improvement, is to reduce the number of issues (i.e., undesirable conditions, defects, failures) and to minimize their impact on quality, delivery performance, and cost. This includes having processes in place to detect and eradicate significant and recurrent issues, which implies having well identified problems, a common understanding of their impact and associated root causes, and having defined and implemented adequate actions so that these problems, including similar issues will not happen again.

This standard establishes requirements for performing and documenting APQP and PPAP. APQP begins with conceptual product needs and extends through product definition, production planning, product and process validation (i.e., PPAP), product use, and post-delivery service. This standard integrates and collaborates with the requirements of the 9100, 9102, 9103, and 9110 standards. The requirements specified in this standard are complementary (not alternative) to contractual and applicable statutory and regulatory requirements. Should there be a conflict between the requirements of this standard and applicable statutory or regulatory requirements, the latter shall take precedence.

This document is intended to prescribe consistent requirements for CSI management for organizations and suppliers who perform work for prime contractors receiving direct contracts from U.S. government agencies (i.e., first-tier or prime suppliers).

This Standard defines uniform Quality and Technical requirements relative to metallic parts marking performed in using "Data Matrix symbology" (2D) coding used within the aerospace industry. The ISO 16022 specifies general requirements (data characters encodation, error correction rules, decoding algorithm, etc.). In addition to this specification, part Identification with such coding is subject to the following requirements to ensure electronic reading (scanning) ability of the symbol. The marking processes covered by this standard are as follows: Dot Peening Laser Marking Electro-Chem Etching Further marking processes will be included if required. Unless specified otherwise in the contractual business relationship, the company responsible for the design of the part shall determine the location of the Data Matrix Marking. Symbol position should allow illumination from all sides for readability.

This SAE Aerospace Standard (AS) defines uniform Quality and Technical requirements relative to metallic parts marking performed in using "Data Matrix symbology" used within the aerospace industry. The ISO/IEC 16022 specifies general requirements (data character encodation, error correction rules, decoding algorithm, etc.). In addition to ISO/IEC 16022 specification, part identification with such symbology is subject to the following requirements to ensure electronic reading of the symbol. The marking processes covered by this standard are as follows: Dot Peening Laser Electro-Chemical Etching Further marking processes will be included if required. This standard does not specify information to be encoded. Unless specified otherwise in the contractual business relationship, the company responsible for the design of the part shall determine the location of the Data Matrix Marking. Symbol position should allow optimum illumination from all sides for readability.

The basic requirements of AS9100A apply with the following clarifications. This document supplements the requirements of AS9100A for deliverable software. This supplement contains Quality System requirements for suppliers of products that contain deliverable embedded or loadable airborne, spaceborne or ground support software components that are part of an aircraft Type Design, weapon system, missile or spacecraft operational software and/or support software that is used in the development and maintenance of deliverable software. This includes the host operating system software including assemblers, compilers, linkers, loaders, editors, code generators, analyzers, ground simulators and trainers, flight test data reduction, etc., that directly support creation, test and maintenance of the deliverable software.

The basic requirements of AS9100A apply with the following clarifications. This document supplements the requirements of AS9100A for deliverable software. This supplement contains Quality System requirements for suppliers of products that contain deliverable embedded or loadable airborne, spaceborne or ground support software components that are part of an aircraft Type Design, weapon system, missile or spacecraft operational software and/or support software that is used in the development and maintenance of deliverable software. This includes the host operating system software including assemblers, compilers, linkers, loaders, editors, code generators, analyzers, ground simulators and trainers, flight test data reduction, etc., that directly support creation, test and maintenance of the deliverable software.

This document contains the minimum requirements for supplier Inspection and Test Quality System. It is emphasized that the quality system requirements specified in this standard are complementary (not alternative) to the contractual and applicable law and regulatory requirements.