Search Results

A biodynamic model of the spine simulated the action of spinal musculature on the head, vertebral bodies and pelvis in the midsagittal plane. Muscle was treated as a force generator whose contractile force was dependant on muscle stretch, stretch rate and neural delay time. Eight model runs were conducted with and without muscle, simulating +Gz and -Gx impact acceleration. The model predicted that spinal musculature was incapable of affecting overall spinal column kinematics. However, as a result of muscle contraction, significantly higher local axial forces were predicted in the discs and facets than were predicted when muscle was absent.

The effect of muscular response on occupant dynamics was studied in human volunteers exposed to low level impact acceleration. The study includes identification of muscular response, correlation of electromyographic activity with reaction force, and investigation of the effects of muscular restraint during impact. Human volunteers were subjected to −Gx impact acceleration in a simulated automobile environment while EMG activity of various lower extremity muscles was monitored. The seat and floor pan were supported on load cells which measured all restraining forces. Nine–accelerometer modules and high-speed photography were used to measure kinematics. Identical runs were made with an embalmed cadaver and dummy for comparison. Static EMG and force traces as well as dynamic results for various acceleration levels are presented. Differences between tensed and relaxed states are compared and discussed as to EMG response, force levels, and head kinematics.

Spinal kinematics of the living human volunteers undergoing -Gx impact acceleration are described along with the experimental procedures followed to acquire such data. There were 4 male and 3 female volunteers who were subjected to impacts in the tensed and relaxed mode from 2 - 8 g, in 1-g increments. Their lower extremities were tightly clamped to the impact seat and the pelvis was restrained by a lapbelt. The biodynamic response of the living spine is quite similar to that of the cadaveric spine, particularly in terms of T1 displacement, acceleration at T1 and flexural resistance. Female volunteers tend to withdraw from the test program at lower g-levels than males due to transient neck pain.

This paper contains a review of current information on biological structure, material properties and failure characteristics of bone, articular cartilage, ligament and tendon. The load-deformation response of biological tissues is presented with particular reference to the microstructure of the material. Although many of the tissues have been characterized as linear, elastic and isotropic materials, they actually have a more complicated response to load, which includes stiffening with increasing strain, inelastic yield, and strain rate sensitivity. Failure of compact and cancellous bone depends on the rate, type, and direction of loading. Soft biological tissues are vlscoelastie and exhibit a higher load tolerance with an increasing rate of loading. The paper includes a discussion on the basic principles of biomechanics and emphasizes material properties and failure characteristics of biological tissues subjected to impact loading.

Life threatening chest injury can involve partial or full tears of the aorta. Investigations of fatal injuries in automobile accidents indicate that aortic trauma occurs in 10-20% of the cases. The major sites of aortic trauma include the aortic isthmus, the root, and the aortic insertion at the diaphragm - all of which are points of aortic tethering. The biomechanics of the injury process involve stretching of the vessel from points of tethering and hydrodynamic increases in blood pressure, which stretch the tissue to failure at a strain of about 150%. The non-isotropic stretch response of aortic tissue is discussed with reference to the frequent transverse orientation of the laceration. Congenital and pathophysiological conditions also influence the failure characteristics of the tissue. The significant factors associated with traumatic injury of the aorta are discussed in this review paper which is based on published technical information.

In this study, U.S. crash data was analyzed to better understand bounce-over rollovers. Crash data was reviewed to evaluate the distribution of bounce-over crashes and injuries, initiation objects and impact locations. In passenger cars, bounce-over crashes account for 8.4% of rollovers but involve 36.2% of the seriously injured belted drivers. Most bounce-overs are initiated by contact with narrow objects such as a pole, tree or barrier, or large objects such as a ditch or embankment. Contact often occurs in the front of the vehicle. After contact, the vehicle yaws and rolls, and serious injuries are often sustained to the head. Based on field data, a laboratory test was developed to simulate a narrow object bounce-over. The test consists of towing a vehicle laterally on a fixture towards a stationary, angled barrier resting in gravel. The moving fixture is decelerated and the vehicle is released. The vehicle front impacts the edge of the barrier, simulating a narrow object impact.

In 1995, new seat specifications were adopted by GM to provide high retention and improve occupant safety in rear crashes. With more than five years of phase-in of high retention (HR) seats, an analysis of FARS was undertaken to determine the initial field performance of HR seats in preventing fatalities. The 1991-2000 FARS was sorted for fatal rear-impacted vehicles. Using a VIN decoder, GM vehicles with HR front seats were sorted from those with baseline (pre-HR) seats. The fatal rear-impacted vehicle crashes were subdivided into several groups for analysis: 1) single-vehicle rear impacts, 2) two-vehicle rear crashes involving light striking vehicles, and 3) two-vehicle crashes involving heavy trucks and tractor-trailers, and multi-vehicle (3+) rear crashes.

For several decades, there has been a debate on the safety merits of yielding and rigidized (stiff) seats. In 1995, GM adopted requirements for high retention seats and introduced a new generation of yielding seatbacks. These seats have the same stiffness as the yielding seats of the 1980s and early 1990s, but have a strong frame structure and recliners to substantially limit seatback rotation in severe rear crashes. The yielding behavior is given by compliance of the seat suspension across the side structures and an open perimeter frame, which allows the occupant to penetrate into the seatback. The purpose of this study is to compare the energy transfer characteristics and occupant dynamics of yielding and stiff seats in 35 km/h and 16 km/h rear crashes. Based on benchmarking tests, the stiff seatback is defined as one having a 40 kN/m stiffness in rearward loading by a Hybrid dummy.

Purpose: This study presents cases of fracture-dislocation of the thoracic spine in extension during severe rear impacts. The mechanism of injury was investigated. Methods: Four crashes were investigated where a lap-shoulder-belted, front-seat occupant experienced fracture-dislocation of the thoracic spine and paraplegia in a severe rear impact. Police, investigator and medical records were reviewed, the vehicle was inspected and the seat detrimmed. Vehicle dynamics, occupant kinematics and injury mechanisms were determined in this case study. Results: Each case involved a lap-shoulder-belted occupant in a high retention seat with ≻1,700 Nm moment or ≻5.5 kN strength for rearward loading. The crashes were offset rear impacts with 40-56 km/h delta V involving under-ride or override by the impacting vehicle and yaw of the struck vehicle. In each case, the occupant's pelvis was restrained on the seat by the open perimeter frame of the seatback and lap belt.

A series of 10 full-scale experimental simulations of pedestrian-vehicle impact was carried out using cadavers and a 95th percentile anthropomorphic dummy. The test subjects were impacted laterally and frontally at 24, 32 and 40 km/h (15, 20 and 24 mph). Each subject was extensively instrumented with miniature accelerometers, up to a maximum of 53 transducers. The nine-accelerometer scheme was used to measure angular acceleration of body segments from which it was possible to compute the head injury criterion (HIC) for cadaver head impact. A full-size Chevrolet was used as the impacting vehicle. The impact event was three-dimensional in nature during which the body segments executed complex motions. Dummy impacts were more repeatable than cadaver impacts but the response of these test subjects were quite different. The HIC was higher for head-hood impact than for head-ground impact in two of the cases analyzed.

This paper covers the development of the General Motors Energy Absorbing Steering System beginning with the work of the early crash injury pioneers Hugh DeHaven and Colonel John P. Stapp through developments and introduction of the General Motors energy absorbing steering system in 1966. evaluations of crash performance of the system, and further improvement in protective function of the steering assembly. The contributions of GM Research Laboratories are highlighted, including its safety research program. Safety Car, Invertube, the biomechanic projects at Wayne State University, and the thoracic and abdominal tolerance studies that lead to the development of the Viscous Injury Criterion and self-aligning steering wheel.

In the early 1980's a series of tests was conducted simulating rear-end crashes. The tests demonstrated that a conventional automotive bucket seat adequately retains an unbelted dummy on the seat for rear-end impacts up to 6.4 m/s and 9.5 g severity. For this severity of impact the total rearward rotation of the seatback is less than 60° from the vertical and is associated with a normal acceleration of the dummy's chest into the seatback of up to 10 g. The tangential acceleration of the dummy, which may induce riding up the seat, was generally less than the normal component so that the occupant was prevented from sliding up the deflected seatback. The bucket seat provided adequate containment and control of occupant displacements for each of the initial seatback angles of 9°, 22°, and 35°.

Objective: This study analyzes rear sled tests with a 95th% male and 5th% female Hybrid III dummy in various seating positions on ABTS (All Belt to Seat) seats in severe rear impact tests. Dummy interactions with the deforming seatback and upper body extension around the seat frame are considered. Methods: The 1st series involved an open sled fixture with a Sebring ABTS seat at 30 mph rear delta V. A 95th% Hybrid III dummy was placed in four different seating positions: 1) normal, 2) leaning inboard, 3) leaning forward and inboard, and 4) leaning forward and outboard. The 2nd series used a 5th% female Hybrid III dummy in a Grand Voyager body buck at 25 mph rear delta V. The dummy was leaned forward and inboard on a LeSabre ABTS or Voyager seat. The 3rd series used a 5th% female Hybrid III dummy in an Explorer body buck at 26 mph rear delta V. The dummy was leaned forward and inboard on a Sebring ABTS or Explorer seat.

Seventeen side impact sled tests were performed using a horizontally accelerated sled and a Heidelberg-type seat fixture. In these tests the subject's whole body impacted a sidewall with one of three surface conditions: 1) a flat, rigid side wall, 2) an unpadded side wall with a 6″ pelvic offset, or 3) a flat, padded side wall. Forces, deformations and accelerations of the thorax were measured. VCmax emerged as a good injury criterion in this test series. In the WSU-CDC tests VCmax was 0.86 m/s for the half-chest at 25% probability of AIS 4. In addition, a new criterion we have termed “Average Spine Acceleration” (ASA) performed well. ASA is obtained by integrating the T12-y spinal acceleration to obtain spine velocity. The slope of the spine velocity trace is the Average Spine Acceleration, and reflects the rate of momentum transfer to the body during an impact.

As part of a continuing study of thoracic injury resulting from blunt frontal loading, the interrelationship of velocity and chest compression was investigated in a series of animal experiments. Anesthetized male swine were suspended in their natural posture and subjected to midsternal, ventrodorsad impact. Twelve animals were struck at a velocity of 14.5 ± 0.9 m/s and experienced a controlled thoracic compression of either 15, 19, or 24%. Six others were impacted at 9.7 ± 1.3 m/s with a greater mean compression of 27%. For the 14.5 m/s exposures the severity of trauma increased with increasing compression, ranging from minor to fatal. Injuries included skeletal fractures, pulmonary contusions, and cardiovascular ruptures leading to tamponade and hemothorax. Serious cardiac arrhythmias also occurred, including one case of lethal ventricular fibrillation. The 9.7 m/s exposures produced mainly pulmonary contusion, ranging in severity from moderate to critical.

Injury and disability associated with head (brain), neck (spinal cord) and facial injury account for 61.7% of the total societal Harm in the most recent estimate of motor-vehicle related crash injuries. This paper discusses the need for accurate information on translational and rotational acceleration of the head as the first step in critiquing the Head Injury Criterion (HIC) and other injury predictive methods, and developing a fuller understanding of brain and spinal cord injury mechanisms. A measurement system has been developed using linear accelerometers to accurately determine the 3D translational and rotational acceleration of the Hybrid III dummy head. Our concept has been to use the conventional triaxial accelerometer in the dummy's head to assess translational acceleration, and three rows of in-line linear accelerometers and a least squares analysis to compute statistical best-fits for the rotational acceleration about three orthogonal axes.

During the past decade, there has been a steady increase in studies addressing rollover crashes and injuries. Though rollovers are not the most frequent crash type, they are significant with respect to serious injury and interest in rollovers has grown with the introduction of SUVs, vans, and light trucks. A review of Occupant and Vehicle Responses in Rollovers examines relevant conditions for field roll overs, vehicle responses, and occupant kinetics in the vehicle. This book edited by Dr. David C. Viano and Dr. Chantal S. Parenteau includes 62 technical documents covering 15 years of rollover crash safety, including field crash statistics, pre- and rollover dynamics, test procedures and dummy responses.

The influence of body posture, and inherently support, on thoracic impact response was investigated in an animal model. Anesthetized and postmortem domestic swine were exposed to blunt, midsternal loading while supported in their natural quadrupedal posture, and the results were compared with previously reported data from similar tests involving an upright body orientation. Twelve male animals were tested, six while anesthetized and six postmortem. Each animal was impacted once by a 21 kg rigid mass with a flat contact interface moving at a nominal velocity of either 8 or 10 m/s. Measured mechanical responses included applied load, sternal and spinal accelerations, thoracic compression and aortic overpressure. Injury response was assessed from a thoracico-abdominal necropsy. In addition, ECG traces were recorded pre and postimpact to monitor electro-physiological response.

This paper reviews issues relating to seats including design for comfort and restraint, mechanics of discomfort and irritability, older occupants, and low-back pain. It focuses on the interface between seating technology and occupant comfort, and involves a technical review of medical-engineering information. The dramatic increase in the number of features currently available on seats outreaches the technical understanding of occupant accommodation and ride comfort. Thus, the current understanding of seat design parameters may not adequately encompass occupant needs. The review has found many pathways between seating features and riding comfort, each of which requires more specific information on the biomechanics of discomfort by pressure distribution, body support, ride vibration, material breathability, and other factors. These inputs stimulate mechanisms of discomfort that need to be quantified in terms of mechanical requirements for seat design and function.

Role of the Seat in Rear Crash Safety addresses the historic debate over seatback stiffness, energy absorbing yielding, occupant retention and whiplash prevention; and it provides a scientific foundation for the direction GM pursued in the development and validation of future seat designs. It also describes the multi-year research study into the role of the seat in rear crash safety - first by addressing the need for occupant retention in the more severe rear crashes; and then by addressing the needs for an adequately positioned head restraint and changes in the compliance of the seatback to lower the risks of the whiplash in low-speed crashes.