Search Results

Further advancing key technologies requires the optimization of increasingly complex systems with strongly interacting parameters—like efficiency optimization in engine development for optimizing the use of energy. Systematic optimization approaches based on metamodels, so-called Metamodel-Based Design Optimization (MBDO), present one key solution to these demanding problems. Recent advanced methods either focus on Single-Objective Optimization (SoO) on local metamodels with online adaptivity or Multiobjective Optimization (MoO) on global metamodels with only limited adaptivity. In the scope of this work, a fully online adaptive (“in the loop”) optimization approach, capable of both SoO and MoO, is developed which automatically approximates the global system response and determines the (Pareto) optimum.

Laser induced fluorescence (LIF) is used to investigate oil transport mechanisms under real engine conditions. The engine oil is mixed with a dye that can be induced by a laser. The emitted light intensity from the dye correlates with the residual oil at the sensor position and the resulting oil film thicknesses can be precisely determined for each crank angle. However, the general expectation is not always achieved, e.g. an exact representation of piston ring barrel shapes. In order to investigate the responsible lubrication effects of this behavior, a new cavitation algorithm for the Reynolds equation has been developed. The solution retains the mass conservation and does not use any switch function in its mathematical approach. In contrast to common approaches, no vapor-liquid ratio is used, but one or several bigger bubbles are approximated, as have been observed in other experiments already.

The European Commission has released strict emission regulations for passenger cars in the past decade in order to improve air quality in cities and limit harmful emission exposure to humans. In the near future, even stricter regulations containing more realistic/demanding driving scenarios and covering more exhaust gas components are expected to be released. Passenger cars fueled with gasoline are one contributor to unhealthy air conditions, due to the fact that gasoline engines emit harmful air pollutants. One option to minimize harmful emissions would be to utilize specifically tailored, low emission synthetic fuels or fuel blends in internal combustion engines. Methyl formate and dimethyl carbonate are two promising candidates to replace or substitute gasoline, which in previous studies have proven to significantly decrease harmful pollutants.

Improving fuel efficiency while meeting relevant emission limits set by emissions legislation is among the main objectives of engine development. Simultaneously the development costs and development time have to be steadily reduced. For these reasons, the high demands in terms of quality and validity of measurements at the engine test bench are continuously rising. This paper will present a new methodology for efficient testing of an industrial combustion engine in order to improve the process of decision making for combustion-relevant component setups. The methodology includes various modules for increasing measurement quality and validity. Modules like stationary point detection to determine steady state engine behavior, signal quality checks to monitor the signal quality of chosen measurement signals and plausibility checks to evaluate physical relations between several measurement signals ensure a high measurement quality over all measurements.

In order to meet the severe emission restrictions imposed by SULEV and EURO V standards the catalytic converter must reach light-off temperature during the first 20 seconds after engine cold start. Thermal losses in the exhaust manifold are driven by the heat transfer of the pulsating and turbulent exhaust flow and affect significantly the warm-up time of the catalyst. In the present paper an investigation concerning the gas-side heat transfer in the exhaust system of a spark ignited (SI) combustion engine with retarded ignition timing and secondary air injection into the exhaust port is reported. Based on this analysis, the warm-up simulation of a one-dimensional flow simulation tool is improved for an evaluation of different exhaust system configurations.

Presented within the framework of this SAE Technical Paper are the highly accurate results of friction experiments, performed upon a floating-liner, single-cylinder test engine with a capacity 0.5 liters and crank angle resolution during motored and fired operation. This allows for the measurement of mixed friction zones at the dead centers. These mixed friction zones can result in friction losses and lead to wear in the components in-volved. The strength of the friction forces in any given mixed friction zone is largely dependent on the operating point. This is why the influence of each of the most important operating parameters - speed (rpm), load, oil and coolant temperature - is individually analysed, before the interactions, which are depicted in the resultant engine map, are discussed.

Synthetic fuels for internal combustion engines offer CO2-neutral mobility if produced in a closed carbon cycle using renewable energies. C1-based synthetic fuels can offer high knock resistance as well as soot free combustion due to their molecular structure containing oxygen and no direct C-C bonds. Such fuels as, for example, dimethyl carbonate (DMC) and methyl formate (MeFo) have great potential to replace gasoline in spark-ignition (SI) engines. In this study, a mixture of 65% DMC and 35% MeFo (C65F35) was used in a single-cylinder research engine to determine friction losses in the piston group using the floating-liner method. The results were benchmarked against gasoline (G100). Compared to gasoline, the density of C65F35 is almost 40% higher, but its mass-based lower heating value (LHV) is 2.8 times lower. Hence, more fuel must be injected to reach the same engine load as in a conventional gasoline engine, leading to an increased cooling effect.

This SAE Technical Paper contains detailed data which are relevant for the calculation of the friction forces of the piston assembly in internal combustion engines. Useful ways of employing calculations besides measurements are exactly classified for the optimization of the piston assembly system in order to reduce friction losses. In the first step the theoretical basics for the calculation of the tribological system are introduced. Referring to the theory, the paper goes into detail about the basic set-up and the modeling degree of the calculation program. Furthermore, measured and calculated curves of friction forces are compared for different operating points. In addition, analysis of the crank-angle resolved friction force are presented with varying engine speeds, oil temperatures and loads and a detailed interpretation of the results is given.

A new constant volume combustion chamber (CVCC) apparatus is presented that calculates the cetane number (CN) of fuels from their ignition delay by means of a primary reference fuel calibration. It offers the benefits of low fuel consumption, suitability for non-lubricating substances, accurate and fast measurements and a calibration by primary reference fuels (PRF). The injection system is derived from a modern common-rail passenger car engine. The apparatus is capable of fuel injection pressures up to 1200 bar and requires only 40 ml of the test fuel. The constant volume combustion chamber can be heated up to 1000 K and pressurized up to 50 bar. Sample selection is fully automated for independent operation and low levels of operator involvement. Capillary tubes employed in the sampling system can be heated to allow the measurement of highly viscous fuels.

On the way to a climate-neutral mobility, synthetic fuels with their potential of CO2-neutral production are currently in the focus of internal combustion research. In this study, the C1-fuels methanol (MeOH), dimethyl carbonate (DMC), and methyl formate (MeFo) are tested as pure fuel mixtures and as blend components for gasoline. The study was performed on a single-cylinder engine in two configurations, thermodynamic and optical. As pure C1-fuels, the previously investigated DMC/MeFo mixture is compared with a mixture of MeOH/MeFo. DMC is replaced by MeOH because of its benefits regarding laminar flame speed, ignition limits and production costs. MeOH/MeFo offers favorable particle number (PN) emissions at a cooling water temperature of 40 °C and in high load operating points. However, a slight increase of NOx emissions related to DMC/MeFo was observed. Both mixtures show no sensitivity in PN emissions for rich combustions. This was also verified with help of the optical engine.

The thermal and emission efficiency of diesel engines depends to a large extent on the quality of fuel injection. However, over engine lifetime, injection rate and quality will change due to adverse nozzle aging effects, such as coking or cavitation. In this study, we discuss the influences of these effects on injection and heat release rate. The injection rates of previously unused nozzles and a nozzle that had been operated in a vehicle engine were compared in order to clarify the impact of aging effects. The key to the detection of alterations of injection nozzles is the identification of strongly correlating parameters. As a first step, an instrumented injector was set up to measure fuel pressure inside the feed line of the injector and the lift of the control piston. Different nozzles showed a distinguishable control piston motion depending on their different geometric specifications, which also affect the injection rates.

Modern methods of engine development use complex mathematical models. Adding advanced components such as variable valve trains or direct injection systems to the model increases the degrees of freedom resulting in a high number of measurements for validation. Steadily rising costs for development, time and staff make it crucial for industry to improve the quality of measurements with advanced analysis techniques. Often, such models consider the simulated system as stationary, implying that system variables no longer change with time. This paper presents an internal combustion engine measurement system utilizing algorithms for the real-time evaluation of the state of the engine or its components. Several approaches have been reviewed and tested regarding their applicability. The most straightforward algorithms compare the gradient of a sensor signal to a pre-defined threshold.

For the next stage of Homogeneous Charge Compression Ignition (HCCI) engine researches, the development of an engine controller, taking account of dynamics is required. The objective of this paper is to develop dynamic multi input and multi output HCCI engine models and a controller to deal with variable valve lift, variable valve phase, and fuel injection. First, a physical continuous model has been developed. This model mainly consists of air flow models, an ignition model, and a combustion and mechanical model of the engine. The flow models use a receiver model on volumetric elements such as an intake manifold and a valve flow model on throttling elements such as intake valves. Livengood-wu integration of Arrhenius function is used to predict ignition timing. The combustion duration is expressed as a function of ignition timings.

In this project funded by the Bayerische Forschungsstiftung two fundamental investigations had been carried out: first a new N-rich liquid ammonia precursor solution based on guanidine salts had been completely characterized and secondly a new type of side-flow reactor for the controlled catalytic decomposition of aqueous NH₃ precursor to ammonia gas has been designed, applied and tested in a 3-liter passenger car diesel engine. Guanidine salts came into the focus due to the fact of a high nitrogen-content derivate of urea. Specially guanidinium formate has shown extraordinary solubility in water (more than 6 kg per 1 liter water at room temperature) and therefore a possible high ammonia potential per liter solution compared to the classical 32.5% aqueous urea solution (AUS32) standardized in ISO 22241 and known as DEF (diesel emission fluid), ARLA32 or AdBlue® .

In the present work the benefit of a 50 MPa gasoline direct injection system (GDI) in terms of particle number (PN) emissions as well as fuel consumption is shown on a 0.5 l single cylinder research engine in different engine operating conditions. The investigations show a strong effect of injection timing on combustion duration. As fast combustion can be helpful to reduce fuel consumption, this effect should be investigated more in detail. Subsequent analysis with the method of particle image velocimetry (PIV) at the optical configuration of this engine and three dimensional (3D) computational fluid dynamics (CFD) calculations reveal the influence of injection timing on large scale charge motion (tumble) and the level of turbulent kinetic energy. Especially with delayed injection timing, high combustion velocities can be achieved. At current series injection pressures, the particle number emissions increase at late injection timing.

The development of today's powertrains focuses on the reduction of CO₂ emissions. Therefore several new technologies for internal combustion engines have been established. A further tendency is the successive electrification of powertrains in hybrid vehicles. However, these trends lead to increasing system costs which are a very important aspect at the market segment of compact cars. At the Institute of Internal Combustion Engines of the Technical University of Munich a drivetrain concept for urban and commuter traffic is under development. It is based on a lean-burn air-cooled two-cylinder natural gas engine which is combined with a hydraulic hybrid system. The paper contains detailed information about the engine as well as the hybrid vehicle powertrain in parallel structure. Particular characteristics and innovations of the hydraulic hybrid system compared to systems known so far are shown.

This paper discusses research activities at the Technische Universität München on the HCCI combustion process, focusing on the development of a model-based control concept with pressure indication. As a first step sensitivity analyses have been carried out to investigate influences of different injection strategies on the combustion and emission characteristics. An optimal injection strategy has been determined and reasonable control variables and ranges corresponding to this strategy were defined. Comprehensive steady-state measurements have been conducted to detect the engine characteristics. In order to limit the experimental effort, principles of DoE (Design of Experiments) have been used to define a methodological approach in the planning of the measurements. Afterwards a multiple-input multiple-output engine model including boundary models for input settings has been designed out of the measurement results.

Beside the main trend technologies such as downsizing, down speeding, external exhaust gas recirculation, and turbocharging in combination with Miller cycles, the optimization of the mechanical efficiency of gasoline engines is an important task in meeting future CO2 emission targets. Friction in the piston assembly is responsible for up to 45% of the total mechanical loss in a gasoline engine. Therefore, optimizing piston assembly friction is a valuable approach in improving the total efficiency of an internal combustion engine. The form honing process enables new specific shapes of the cylinder liner surface. These shapes, such as a conus or bottle neck, help enlarge the operating clearance between the piston assembly and the cylinder liner, which is one of the main factors influencing piston assembly friction.

Polyoxymethylene dimethyl ethers (OME) are promising alternative diesel fuels with a biogenic or electricity-based production, which offer carbon neutral mobility with internal combustion engines. Among other e-fuels, they stand out because of soot-free combustion, which resolves the trade-off between nitrogen oxide (NOx) and soot emissions. Additionally, long-chain OME have a high ignitability, indicated by a cetane number (CN) greater than 70. This opens up degrees of freedom in the injection strategy and enables simplifications compared to the operation with fossil diesel. This study investigates the hydraulic behavior of two solenoid injectors with different injector geometry for heavy-duty applications on an Injection Rate Analyzer (IRA) in diesel and OME operation. For OME, both injectors show longer injection delays in all injection pressure ranges investigated, increasing with rail pressure.

Due to its molecular structure, methane provides several advantages as fuel for internal combustion engines. To cope with nitrogen oxide emissions high levels of excess air are beneficial, which on the other hand deteriorates the flammability and combustion duration of the mixture. One approach to meet these challenges and ensure a stable combustion process are fuelled prechambers. The flow and combustion processes within these prechambers are highly influenced by the position, orientation, number and overall cross-sectional area of the orifices connecting the prechamber and the main combustion chamber. In the present study, a water-cooled single cylinder test engine with a displacement volume of 0.5 l is equipped with a methane-fuelled prechamber. To evaluate influences of the aforementioned orifices several prechambers with variations of the orientation and number of nozzles are used under different operating conditions of engine speed and load.