Search Results

This paper aims to validate chemical kinetic mechanisms of surrogate gasoline three components fuel by calculating one-dimensional laminar burning velocity of iso-octane/air mixture. Next, the application of level-set method on premixed combustion without consideration the effect of turbulence eddies on flame front is also studied in three-dimensional computational fluid dynamic (3D-CFD) simulation. In the 3D CFD simulation, there is an option to calculate laminar burning velocity by using empirical correlations, however it is applicable only for particular initial pressure and temperature in spark ignition engine cases. One-dimensional burning velocities from lean to rich of iso-octane/air mixture are calculated by using CHEMKIN-PRO with detailed chemistry and transport phenomena as a function of different equivalence ratios, different unburnt temperature and pressure ranges.

This paper describes the development of an integrated simulation model for evaluating the effects of electrically heating the three-way catalyst (TWC) in a series hybrid electric vehicle (s-HEV) on fuel economy and exhaust gas purification performance. Engine and TWC models were developed in GT-Power to predict exhaust emissions during transient operation. These models were validated against data from vehicle tests using a chassis dynamometer and integrated into an s-HEV model built in MATLAB/Simulink. The s-HEV model accurately reproduced the performance characteristics of the vehicle’s engine, motor, generator, and battery during WLTC mode operation. It can thus be used to predict the fuel consumption, emissions, and performance of individual powertrain components. The engine combustion characteristics were reproduced with reasonable accuracy for the first 50 combustion cycles, representing the cold-start condition of the driving mode.

A three-dimensional computational fluid dynamics (3D-CFD) code was combined with a detailed combustion chamber heat transfer model. The established model allowed not only prediction of instantaneous combustion chamber wall surface temperature distributions in practical calculation time but also investigation of the characteristics of combustion, emissions and heat losses affected by the wall temperature distributions. Although zero-dimensional combustion analysis can consider temporal changes in the heat transfer coefficient and in-cylinder gas temperature, it cannot take into account the effect of interactions between spatially distributed charge and wall temperatures. In contrast, 3D-CFD analysis can consider temporal and spatial changes in both parameters. However, in most zero-/multi- dimensional combustion analyses, wall temperatures are assumed to be temporally constant and spatially homogeneous.

In order to improve thermal efficiency of spark ignition (SI) engines, an improved technology to avoid irregular combustion under high load conditions of high compression ratio SI engines is required. In this study, the authors focused on high pressure gasoline direct injection in a high compression ratio SI engine, which its rapid air-fuel mixture formation, turbulence, and flame speed, are enhanced by high-speed fuel spray jet. Effects of fuel injection pressure, injection and spark ignition timing on combustion characteristics were experimentally and numerically investigated. It was found that the heat release rate was drastically increased by raising the fuel injection pressure. The numerical simulation results show that the high pressure gasoline direct injection enhanced small-scale turbulent intensity and fuel evaporation, simultaneously.

To reproduce wall quenching phenomena using 3D-CFD, a wall quenching model was constructed based on the Peclet number. The model was further integrated with the flame propagation model. Combustion analysis showed that that a large amount of unburned hydrocarbons (UHCs) remained in the piston clevis and small gaps. Furthermore, the model was capable of predicting the increase in UHC emissions when there was a delay in the ignition time. The flame front cells were plotted on Peters' premixed turbulent combustion diagram to identify transitions in the combustion states. It was found that the flame surface transitioned from corrugated flamelets through thin reaction zones to wrinkled flamelets and further to laminar flamelets, which led to wall quenching. The turbulent Reynolds number (Re) decreased rapidly due to the increase in laminar flame speed and flame thickness and the decrease in turbulent intensity and turbulent scale.

A variable valve timing (VVT) mechanism was applied to achieve premixed diesel combustion at higher load for low emissions and high thermal efficiency in a light duty diesel engine. By means of late intake valve closing (LIVC), compressed gas temperatures near the top dead center are lowered, thereby preventing too early ignition and increasing ignition delay to enhance fuel-air mixing. The variability of effective compression ratio has significant potential for ignition timing control of conventional diesel fuel mixtures. At the same time, the expansion ratio is kept constant to ensure thermal efficiency. Combining the control of LIVC, EGR, supercharging systems and high-pressure fuel injection equipment can simultaneously reduce NOx and smoke. The NOx and smoke suppression mechanism in the premixed diesel combustion was analyzed using the 3D-CFD code combined with detailed chemistry.

With the development of downsized spark ignition (SI) engines, low-speed pre-ignition (LSPI) has been observed more frequently as an abnormal combustion phenomenon, and there is a critical need to solve this issue. It has been acknowledged that LSPI is not directly triggered by autoignition of the fuel, but by some other material with a short ignition delay time. It was previously reported that LSPI can be caused by droplets of lubricant oil intermixed with the fuel. In this work, the ignition behavior of lubricant component containing fuel droplets was experimentally investigated by using a constant volume chamber (CVC) and a rapid compression and expansion machine (RCEM), which enable visualization of the combustion process in the cylinder. Various combinations of fuel compositions for the ambient fuel-air mixture and fractions of base oil/metallic additives/fuel for droplets were tested.

Emission regulations are becoming tighter, and Real Driving Emissions (RDE) is proposed as a testing cycle for evaluating modern engine emissions under a wide operation range. For this reason, engine manufacturers have been developing a method to effectively assess engine performances and emissions under a wide range of transient conditions. Transient engine performances can be evaluated efficiently by applying time-series data created by chirp signals. However, when the time-series data produced by the chirp signal are used directly, the engine hardware may damage, and emission performances deteriorate drastically. It is therefore essential to develop a method to avoid these undesirable operating conditions. This work aims to develop an algorithm to avoid such unrealistic operation conditions for engine performance evaluation. A virtual diesel engine (VDE) model is developed based on a four-cylinder engine using GT-POWER software.

The objective of this paper is to investigate the potential of lean burn combustion to improve the thermal efficiency of spark ignition engine. Experiments used a single cylinder gasoline spark ignition engine fueled with primary reference fuel of octane number 90, running at 4000 revolution per minute and at wide open throttle. Experiments were conducted at constant fueling rate and in order to lean the mixture, more air is introduced by boosted pressure from stoichiometric mixture to lean limit while maintaining the high output engine torque as possible. Experimental results show that the highest thermal efficiency is obtained at excess air ratio of 1.3 combined with absolute boosted pressure of 117 kPa. Three dimensional computational fluid dynamic simulation with detailed chemical reactions was conducted and compared with results obtained from experiments as based points.

Alternative propulsion systems such as renewable fuels and electric powertrains are expensive; thus, efficient internal combustion engines (ICE) with hybrid powertrains still play significant roles in the transportation fleet in the coming decades. Modern engine technologies have been adopted to meet stringent emissions and fuel economy standards. As a result, engine control systems are becoming more complex. Furthermore, as ICE control parameters increase exponentially, engine calibration and design become bottlenecks in the development process. While a map-based feed-forward control method is a current de facto standard in combustion control, online closed-loop feedback control can improve engine performance and robustness. However, adding physical sensors to measure the various data for the online feedback control and calibration increase the vehicle cost.

An experimental ultra lightweight compact vehicle named “the Waseda Future Vehicle” has been designed and developed, aiming at a simultaneous achievement of low exhaust gas emissions, high fuel economy and driving performance. The vehicle is powered by a dual-type hybrid system having a SI engine, electric motor and generator. A high performance lithium-ion battery unit is used for electricity storage. A variety of driving cycles were reproduced using the hybrid vehicle on a chassis dynamometer. By changing the logics and parameters in the electronic control unit (ECU) of the engine, a significant improvement in emissions was possible, achieving a very high fuel economy of 34 km/h at the Japanese 10-15 drive mode. At the same time, a numerical simulation model has been developed to predict fuel economy. This would be very useful in determining design factors and optimizing operating conditions in the hybrid power system.

The reduced chemical reaction scheme which can take the effect of major fuel components on auto ignition timing into account has been developed. This reaction scheme was based on the reduced reaction mechanism for the primary reference fuels (PRF) proposed by Tsurushima [1] with 33 species and 38 reactions. Some pre-exponential factors were modified by using Particle Swarm Optimization to match the ignition delay time versus reciprocal temperature which was calculated by the detailed scheme with 2,301 species and 11,116 elementary chemical reactions. The result using the present reaction scheme shows good agreements with that using the detailed scheme for the effects of EGR, fuel components, and radical species on the ignition timing under homogeneous charge compression ignition combustion (HCCI) conditions.

This study examines the effects of ethanol content on engine performances and the knock characteristics in spark ignition gasoline engine under various compression ratio conditions by cylinder pressure analysis, visualization and numerical simulation. The results confirm that increasing the ethanol content provides for greater engine torque and thermal efficiency as a result of the improvement of knock tolerance. It was also confirmed that increasing the compression ratio together with increasing ethanol content is effective to overcome the shortcomings of poor fuel economy caused by the low calorific value of ethanol. Further, the results of one dimensional flame propagation simulation show that ethanol content increase laminar burning velocity. Moreover, the results of visualization by using a bore scope demonstrate that ethanol affects the increase of initial flame propagation speed and thus helps suppress knock.

The purpose of the present study is to find a way to extend a combustion stability limit for diluted combustion in a spark-ignition (SI) gasoline engine which has a high compression ratio. This paper focuses on partial oxidation in an unburned mixture which is observed in the high compression engine and clarifies the effect of partial oxidation in an unburned mixture on the behavior of a flame stretch and the extinction limit. The behavior of the flame stretch was simulated using the detailed chemical kinetics simulation with the opposed-flow flame reactor model. In the simulation, the reactants which have various reaction progress variables were examined to simulate the flame stretch and extinction under the partial oxidation conditions. The mixtures were also diluted by complete combustion products which represent exhaust gas recirculation (EGR).

Battery models are being developed as a component of the powertrain systems of hybrid electric vehicles (HEVs) to predict the state of charge (SOC) accurately. Electrically heated catalysts (EHCs) can be employed in the powertrains of HEVs to reach the catalyst light off temperature in advance. However, EHCs draw power from the battery pack and hence sufficient energy needs to be stored to power auxiliary components. In series HEVs, the engine is primarily used to charge the battery pack. Therefore, it is important to develop a control strategy that triggers engine start/stop conditions and reduces the frequency of engine operation to minimize the equivalent fuel consumption. In this study, a battery pack model was constructed in MATLAB-Simulink to investigate the SOC variation of a high-power lithium ion battery during extreme engine cold start conditions (-7°C) with/without application of an EHC.

In this study, we selected four unregulated emissions species, formaldehyde, benzene, 1,3-butadiene and benzo[a]pyrene to research the emission characteristics of these unregulated components experimentally. The engine used was a water-cooled, 8-liter, 6-cylinder, 4-stroke-cycle, turbocharged DI diesel engine with a common rail fuel injection system manufactured for the use of medium-duty trucks, and the fuel used was JIS second-class light gas oil, which is commercially available as diesel fuel. The results of experiments indicate as follows: formaldehyde tends to be emitted under the low load condition, while 1,3-butadiene is emitted at the low engine speed. This is believed to be because 1,3-butadiene decomposes in a short time, and the exhaust gas stays much longer in a cylinder under the low speed condition than under the high engine speed one. Benzene is emitted under the low load condition, as it is easily oxidized in high temperature.

Synthetic fuels can significantly improve the combustion and emission characteristics of heavy-duty diesel engines toward decarbonizing heavy-duty propulsion systems. This work analyzes the effects of engine operating conditions and synthetic fuel properties on spray, combustion, and emissions (soot, NOx) using a supercharging single-cylinder engine experiment and KIVA-4 code combined with CHEMKIN-II and in-house phenomenological soot model. The blended fuel ratio is fixed at 80% diesel and 20% n-paraffin by volume (hereafter DP). Diesel, DP1 (diesel with n-pentane C5H12), DP2 (diesel with n-hexane C6H14), and DP3 (diesel with n-heptane C7H16) are used in engine-like-condition constant volume chamber (CVC) and engine experiments. Boosted engine experiments (1080 rpm, common-rail injection pressure 160 MPa, multi-pulse injection) are performed using the same DP fuel groups under various main injection timings, pulse-injection intervals, and EGR = 0-40%.

Homogeneous Charge Compression Ignition (HCCI) is effective for the simultaneous reduction of soot and NOx emissions in diesel engine. In general, high octane number fuels (gasoline components or gaseous fuels) are used for HCCI operation, because these fuels briefly form lean homogeneous mixture because of long ignition delay and high volatility. However, it is necessary to improve injection systems, when these high octane number fuels are used in diesel engine. In addition, the difficulty of controlling auto-ignition timing must be resolved. On the other hand, HCCI using diesel fuel (diesel HCCI) also needs ignition control, because diesel fuel which has a low octane number causes the early ignition before TDC. The purpose of this study is the ignition and combustion control of diesel HCCI. The effects of parameters (injection timing, injection pressure, internal/external EGR, boost pressure, and variable valve timing (VVT)) on the ignition timing of diesel HCCI were investigated.

Three types of combustion chamber configurations (Types A, B, and C) with compression ratio lower than that of the baseline were tested for improved performance and exhaust gas emissions from an inline-four-cylinder 1.7-liter common-rail diesel engine manufactured for use with passenger cars. First, three combustion chambers were examined numerically using CFD code. Second, engine tests were conducted by using Type B combustion chamber, which is expected to have the best performance and exhaust gas emissions of all. As a result, 80% of NOx emissions at both low and medium loads at 1500 rpm, the engine speed used frequently in the actual city driving, improved with nearly no degradation in smoke emissions and brake thermal efficiency. It was shown that a large amount of cooled EGR enables NOx-free combustion with long ignition delay.

A dual fuel natural gas diesel engine suffers from remarkably lower thermal efficiency and higher THC, CO emissions at lower load because of its lower burned mass fraction caused by the lean pre-mixture. To overcome this inevitable disadvantage at lower load, two methods of reducing the number of operating cylinders were examined. One method was to use the two cylinders operation while the second one was to use the quasi-two cylinders operation. As a result, it was found that the unburned hydrocarbons and CO emissions could be favorably reduced with the improvement of thermal efficiency by reducing the number of cylinders to half for a dual fuel natural gas diesel engine. Moreover, it was also found that the quasi-two cylinders operation could improve the torque fluctuation more compared to the two cylinders operation.