Search Results

Multidimensional computations were made of combustion of natural gas engine via the KIVA-II code to evaluate the combustion and emission characteristics. In the combustion submodel, a two-step kinetic reaction mechanism is employed to account for oxidation of methane. The first of the two global rate equations controls the disappearance of methane, and the second, the oxidation of carbon monoxide. Four types of combustion chamber and a two-spark-plug geometry are considered to achieve quick flame propagation of the lean air-methane mixture. The effect of spark plug locations on the combustion processes is discussed. The calculated results show that the more effective burning process with lower NOx emission could be achieved by proper design of the geometry of the piston bowl and the arrangement of the spark plug by matching of the flame front development with the in-cylinder gas flow.

The fuel-saving potential of a series hybrid electric vehicle (SHEV) was investigated in this work based on the future goals and technical roadmaps proposed by China's automobile and internal combustion engine (ICE) industry. The genetic algorithm optimization method and dynamic programming energy management strategy are used to optimize the key component parameters of a typical SHEV SUV to improve the fuel economy of the vehicle. Results showed that the fuel consumption of the vehicle would be 3.24 L / 100km in 2035, which is 37.21% less than 5.16 L / 100km in 2020, following the industries’ roadmaps. The results also indicated that the improvement of the ICE’s thermal efficiency is the main reason for the decrease of the vehicle’s fuel consumption. In addition, the improvement of working points and the reduction of energy losses of the key components also contribute to the improvement of the fuel economy.

This paper describes the CFD modeling work conducted for the development and research of a Vortex Induced Stratification Combustion (VISC) system that demonstrated superior fuel economy benefits. The Ford in-house CFD code and simulation methodology were employed. In the VISC concept a vortex forms on the outside of the wide cone angle spray and transports fuel vapor from the spray to the spark plug gap. A spray model for an outward-opening pintle injector used in the engine was developed, tested, and implemented in the code. Modeling proved to be effective for design optimization and analysis. The CFD simulations revealed important physical phenomena associated with the spray-guided combustion system mixing preparation.

In the effort to improve combustion of a Light-load Stratified-Charge Direct-Injection (LSCDI) combustion system, CFD modeling, together with optical engine diagnostics and single cylinder engine testing, was applied to resolve some key technical issues. The issues associated with stratified-charge (SC) operation are combustion stability, smoke emission, and NOx emission. The challenges at homogeneous-charge operation include fuel-air mixing homogeneity at partial load operation, smoke emission and mixing homogeneity at low speed WOT, and engine knock tendency reduction at medium speed WOT operations. In SC operation, the fuel consumption is constrained with the acceptable smoke emission level and stability limit. With the optimization of piston design and injector specification, the smoke emission can be reduced. Concurrently, the combustion stability window and fuel consumption can be also significantly improved.

An innovative stratified-charge DISI combustion concept has been developed using a mixture formation method referred to as Vortex Induced Stratification Combustion (VISC). This paper describes the combustion system concept and an initial assessment of it, performed on a single-cylinder test engine and through CFD modeling. This VISC concept utilizes the vortex naturally formed on the outside of a wide spray cone that is enhanced by bulk gas flow control and piston crown design. This vortex transports fuel vapor from the spray cone to the spark gap. This system allows a late injection timing and produces a well-confined mixture, which together provide an improved compromise between combustion phasing and combustion efficiency over typical wall-guided systems. Testing results indicate an 18% fuel consumption reduction, compared with a baseline PFI engine, over a drive cycle (neglecting cold start and transient effects).

A new Light Stratified-Charge Direct Injection (LSC DI) spark ignition combustion system concept was developed at Ford. One of the new features of the LSC DI concept is to use a ‘light’ stratified-charge operation window ranging from the idle operation to low speed and low load. A dual independent variable cam timing (DiVCT) mechanism is used to increase the internal dilution for emissions control and to improve engine thermal efficiency. The LSC DI concept allows a large relaxation in the requirement for the lean after-treatment system, but still enables significant fuel economy gains over the PFI base design, delivering high technology value to the customer. In addition, the reduced stratified-charge window permits a simple, shallow piston bowl design that not only benefits engine wide-open throttle performance, but also reduces design compromises due to compression ratio, DiVCT range and piston bowl shape constraints.

As the issue of oil shortage and air pollution caused by automotive engine emissions become more and more serious day by day, researchers and engineers from all over the world are seeking for alternative fuels of lower pollution and renewable nature. This paper discusses in detail the feasibility of fueling gasoline engines with Butanol-gasoline blends. Besides the production, transportation, storage, physical and chemical properties of Butanol-gasoline blends, the combustion characteristics were analyzed as well. As the result Butanol was considered an excellent alternative fuel for gasoline engines, with many unique advantages superior to Natural Gas, LPG, Carbinol and Ethanol, the latter are widely studied at present time. In order to validate the above conclusions in engine application, engine dyno tests were conducted for a gasoline engine fueled with different concentrations of Butanol blend ranging from 10% to up to 35%.

Charge cooling due to fuel evaporation in a direct-injection spark-ignition (DISI) engine typically allows for an increased compression ratio relative to port fuel injection (PFI) engines. It is clear that this results in a thermal efficiency improvement at part load for homogenous-charge DISI engines. However, very little is known regarding the effect of compression ratio on stratified charge operation. In this investigation, DISI combustion data have been collected on a single cylinder engine equipped with a variable compression ratio feature. The results of experiments performed in stratified-charge direct injection (SCDI) mode show that despite its over-advanced phasing, thermal conversion efficiency improves with higher compression ratios. This benefit is quantified and dissected through an efficiency analysis. Furthermore, since the engine was equipped with both wall-guided DI and PFI systems, direct comparisons are made at part load for fuel consumption and emissions.

The driving conditions of commercial logistics vehicles have the characteristics of combined urban and suburban roads with relatively fixed mileage and cargo load alteration, which affect the vehicular fuel economy. To this end, an adaptive equivalent consumption minimization strategy (A-ECMS) with vehicle speed and weight recognition is proposed to improve the fuel economy for a range-extender electric van for logistics in this work. The driving conditions are divided into nine representative groups with different vehicle speed and weight statuses, and the driving patterns are recognized with the use of the bagged trees algorithm through vehicle simulations. In order to generate the reference SOC near the optimal values, the optimal SOC trajectories under the typical driving cycles with different loads are solved by the shooting method and the optimal slopes for these nine patterns are obtained.

Numerical analysis of thermal efficiency improvement up to 45% of an 1.8-liter turbocharged direct-injection (DI) gasoline engine was conducted in this study in response to the need of improving vehicle fuel economy. 1D thermodynamics simulations and 3D computational fluid dynamics (CFD) modeling were carried out to investigate the technical approaches for improving engine thermal efficiency. Effects of various technologies on the improvement in the engine performance were evaluated, and then the technical routes to achieve 41% and 45% brake thermal efficiency were summarized, respectively. It is concluded that 41% thermal efficiency can be reached under stoichiometric combustion conditions, while it is expected lean burn technology is needed for the target of 45% thermal efficiency. The effects of high tumble intake flow on accelerating burning speed and of high compression ratio on intensifying knocking were analyzed.

Natural gas is a promising alternative fuel for internal combustion engines due to its rich reserves and low price, as well as good physical and chemical properties. Its low carbon structure and high octane number are beneficial for CO2 reduction and knock mitigation, respectively. Diesel and natural gas dual fuel combustion is a viable pathway to utilize natural gas in diesel engines. To achieve high efficiency and low emission combustion in a practical diesel engine over a wide range of operating conditions, understanding the performance responses to engine system parameter variations is needed. The controllability of two combustion strategies, diesel pilot ignition (DPI) and single injection reactivity controlled compression ignition (RCCI), were evaluated using the multi-dimension CFD simulation in this paper.

Development and research of a stratified-charge direct-injection SI combustion system was carried out at Ford. This paper presents the multidimensional engine CFD modeling analysis of mixture formation and piston surface wetting under the stratified-charge conditions. The effect of various design and operating parameters including piston shape, spray cone angle, swirl ratio, injection timing, engine speed and load on charge stratification and piston-wetting due to spray impingement were studied. The results led to design changes that warranted improvement of engine functions. Of particular interest, the model was shown to be capable to predict piston surface wetting and a qualitative correlation was found between the amount of the remaining liquid fuel on the piston surface and the engine-out smoke number.

The sources of unburned hydrocarbon (UHC) emissions in direct injection stratified charge engines are presented. Whereas crevices in the combustion chamber are the primary sources of UHC emissions in homogeneous charge engines, lean quenching and liquid film layers dominate UHC emissions in stratified charge operation. Emissions data from a single cylinder engine, operating in stratified charge mode at a low speed / light load condition is summarized. This operating point is interesting in that liquid film formation, as evidenced by smoke emissions, is minimal, thus highlighting the lean quenching process. The effects of operating parameters on UHC emissions are demonstrated via sweeps of spark advance, injection timing, manifold pressure, and swirl level. The effects of EGR dilution are also discussed. Spark advance is shown to be the most significant factor in UHC emissions. A semi-empirical model for UHC emissions is presented based on the analysis of existing engine data.

Variable Cam Timing (VCT) has been proven to be a very effective method in PFI (Port Fuel Injection) engines for improved fuel economy and combustion stability, and reduced emissions. In DISI (Direct Injection Spark Ignition) engines, VCT is applied in both stratified-charge and homogeneous charge operating modes. In stratified-charge mode, VCT is used to reduce NOx emission and improve combustion stability. In homogeneous charge mode, the function of VCT is similar to that in PFI engines. In DISI engine, however, the VCT also affects the available fuel-air mixing time. This paper focuses on VCT effects on the induction process and the fuel-air mixing homogeneity in a DISI engine. The detailed induction process with large exhaust-intake valve overlap has been investigated with CFD modeling. Seven characteristic sub-processes during the induction have been identified. The associated mechanism for each sub-process is also investigated.