Search Results

Standard

Continuous Hydrocarbon Analysis of Diesel Emissions

2002-10-21

CURRENT

J215_200210

The method presented is the current recommendation for the use of flame ionization detectors to determine the hydrocarbon content of diesel engine exhaust, or exhaust of vehicles using diesel engines, when operating at steady-state. The requirements of the associated sampling system and a general procedure for a continuous measuring method are presented. This SAE Recommended Practice provides for the continuous measurement of the hydrocarbon concentration in diesel exhaust.

Standard

Crankcase Emission Control Test Code

2012-01-23

CURRENT

J900_201201

The purpose of this SAE STandard is to provide standard test procedures for crankcase emission control systems and/or devices. The procedures included are for determining: a. The flow rate of the blowby of an engine; b. The flow rates through the crankcase emission control system inlet and outlet. This code is written to cover crankcase emission control systems which are designed to reduce the emission of engine blowby gases to the atmosphere. The code includes the following sections: 3. Definitions and Terminology; 4. Test Equipment; 5. Test Procedures; 6. Information and Data to be Recorded; 7. Data Analysis; 8. Presentation of Information and Data.

Standard

EMISSION TEST DRIVING SCHEDULES

1991-06-01

HISTORICAL

J1506_199106

This SAE Information Report describes various dynamometer driving schedules currently in use in the world for measurement of exhaust emissions and fuel economy of passenger cars and light trucks. Issuance of this document will allow driving schedules to be deleted from individual test procedures, thus reducing the amount of repeated information in the SAE Handbook. This document includes: a. Descriptions of driving schedules; and b. Second-by second definition of speed versus time sequences.

Standard

EMISSION TEST DRIVING SCHEDULES

1988-06-01

HISTORICAL

J1506_198806

This SAE Information Report describes various dynamometer driving schedules currently in use in the world for measurement of exhaust emissions and fuel economy of passenger cars and light trucks. Issuance of this information report will allow driving schedules to be deleted from individual test procedures, thus reducing the amount of repeated information in the SAE Handbook. This information report includes: 1 - Descriptions of driving schedules. 2 - Second-by second definition of speed versus time sequences.

Standard

Emission Test Driving Schedules

2002-10-21

CURRENT

J1506_200210

This SAE Information Report describes various dynamometer driving schedules currently in use in the world for measurement of exhaust emissions and fuel economy of passenger cars and light trucks. Issuance of this document will allow driving schedules to be deleted from individual test procedures, thus reducing the amount of repeated information in the SAE Handbook. This document includes: a.) Descriptions of driving schedules and b.) Second-by-second definition of speed versus time sequences.

Standard

Engine Testing with Low-Temperature Charge Air-cooler Systems in a Dynamometer Test Cell

2011-09-06

CURRENT

J1937_201109

The methods presented in this SAE Recommended Practice apply to the controlled testing of low-temperature charge, air-cooled, heavy-duty diesel engines. This document encompasses the following main sections: a Definitions of pertinent parameters b Vehicle testing to determine typical values for these parameters c Description of the setup and operation of the test cell system d Validation testing of the test cell system While not covered in this document, computer modeling of the vehicle engine cooler system is recognized as a valid tool to determine cooler system performance and could be utilized to supplement the testing described. However, adequate in-vehicle testing should be performed to validate the model before it is used for the purposes outlined. The procedure makes references to test cycles that are prescribed by the United States Environmental Protection Agency (US EPA) and are contained in the Code of Federal Regulations.

Standard

Flywheel Spin Test Procedure

2012-10-04

HISTORICAL

J1240_201210

This SAE Recommended Practice applies to flywheels and flywheel-starter ring gear assemblies used with internal combustion engines of spark ignition and diesel type. Engine sizes are those capable of using SAE No. 6 through SAE No. 00 size flywheel housings.

Standard

GUIDE TO THE APPLICATION AND USE OF RADIAL LIP TYPE OIL SEALS

1966-02-01

HISTORICAL

J946_196602

Standard

METHANE MEASUREMENT USING GAS CHROMATOGRAPHY

1991-12-01

HISTORICAL

J1151_199112

This SAE Recommended Practice describes instrumentation for determining the amount of methane in air and exhaust gas.

Standard

METHANE MEASUREMENT USING GAS CHROMATOGRAPHY

1979-07-01

HISTORICAL

J1151A_197907

This SAE Recommended Practice describes instrumentation for determining the amount of methane in air and exhaust gas.

Standard

Manual Transmission and Transaxle Efficiency and Parasitic Loss Measurement

2011-09-02

CURRENT

J2453_201109

Because of the intense focus on CAFE and fuel emission standards, optimization of the automobile drivetrain is imperative. In light of this, component efficiencies have become an important factor in the drivetrain decision-making process. It has therefore become necessary to develop a universal standard to judge transmission efficiency. This SAE Recommended Practice specifies the dynamometer test procedure which maps a manual transmission’s efficiency. The document is separated into two parts. The first compares input and output torque throughout a specified input speed range in order to determine “in-gear” transmission efficiency. The second procedure measures parasitic losses experienced while in neutral at nominal idling speeds and also churning losses while in gear. The application of this document is intended for passenger car and light truck. All references to transmissions throughout this document include transaxles.

Standard

Manual Transmissions and Transaxle High-speed Lubrication, Unbalance, and Seizure Evaluation

2011-09-06

CURRENT

J2132_201109

It is anticipated that this SAE Recommended Practice will be only one step in a comprehensive evaluation of the vehicle/transmission application. This document alone is not adequate “due care” to insure against high-speed seizure or other high-speed problems. The notes printed in bold print throughout the practice convey important information about the test itself or the results and should be considered carefully. All references to transmissions also apply to transaxles, except for the unbalance evaluation which applies only to rear-wheel-drive transmissions with propeller shaft output.

Standard

Methane Measurement Using Gas Chromatography

2011-09-06

CURRENT

J1151_201109

This SAE Recommended Practice describes instrumentation for determining the amount of methane in air and exhaust gas.

Standard

NONMETALLIC GASKETS FOR GENERAL AUTOMOTIVE PURPOSES

1963-04-01

HISTORICAL

J90A_196304

These specifications for SAE J90 are intended to define the basic properties of commercial nonmetallic gasketing materials commonly used in automotive applications. These include materials composed of asbestos or other inorganic fibers, cork, or cellulose or other organic fibers, in combination with various binders or impregnants. Rubber compounds without fibrous or cork reinforcement are not included since they are covered in SAE Standard, Specifications for Elastomer Compounds for Automotive Applications—SAE J14, and in ASTM D 735-61T. Although the test methods and values are designed to describe the basic properties of the material in each category, they do not define all of, the properties which govern gasket performance. Caution should, therefore, be exercised in using these specifications as a basis for the selection of materials.

Standard

OVERCENTER CLUTCH SPIN TEST PROCEDURE

1988-09-01

HISTORICAL

J1079_198809

This recommended practice applies to driving ring type overcenter clutches such as are used in industrial power takeoffs.

Standard

OVERCENTER CLUTCH SPIN TEST PROCEDURE

1995-03-28

HISTORICAL

J1079_199503

This SAE Recommended Practice applies to driving ring type overcenter clutches such as are used in industrial power takeoffs.

Standard

Overcenter Clutch Spin Test Procedure

2012-10-23

CURRENT

J1079_201210

This SAE Recommended Practice applies to driving ring type overcenter clutches such as are used in industrial power takeoffs.

Standard

RADIAL LIP SEAL TORQUE: MEASUREMENT METHODS AND RESULTS

1989-06-01

HISTORICAL

J1971_198906

Standard

REPORTING ON EMISSION TESTING FOR IN-USE LIGHT-DUTY TRUCKS AND PASSENGER VEHICLES

2000-10-01

HISTORICAL

J1712_200010

This SAE Recommended Practice applies to the reporting of laboratory and test site data from the gaseous and evaporative emission tests of in-use light-duty trucks and passenger vehicles. This document describes the reporting of procedures, fuel specifications, and vehicle information necessary to compare the results of in-use tests. Any variations in vehicles, instrumentation, test equipment, or test program purpose should be adequately described.

Standard

RUBBER RINGS FOR AUTOMOTIVE APPLICATIONS

1995-06-29

HISTORICAL

J120_199506

This SAE Recommended Practice covers the dimensional and material requirements of rubber O-rings for automotive application and rectangular section rubber seal rings for automotive applications.