Search Results

Standard

Alignment of Nut Slots

1990-01-01

CURRENT

J484_199001

This method of gaging alignment of nut slots allows equal variations for location of the cotter pin hole in the bolt and location of slots in the nut. To inspect the nut, the slotted gage is inserted through the nut hole from the bearing surface of the nut. Alignment of slots is considered satisfactory if the gage pin can be slipped into the gage and nut slots without interference.

Standard

BOLT AND CAPSCREW SIZES FOR USE IN CONSTRUCTION AND INDUSTRIAL MACHINERY

1994-06-01

HISTORICAL

J370_196811

This SAE Recommended Practice covers the use of preferred bolt and capscrew sizes, wherever applicable, on construction and industrial machinery to ease serviceability.

Standard

BOLT AND CAPSCREW SIZES FOR USE IN CONSTRUCTION AND INDUSTRIAL MACHINERY

1994-06-01

HISTORICAL

J370_199406

This SAE Recommended Practice covers the use of preferred bolt and capscrew sizes, wherever applicable, on construction and industrial machinery to ease serviceability.

Standard

Blind Rivets - Break Mandrel Type

2017-01-04

CURRENT

J1200_201701

This SAE Standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly.

Standard

Blind Rivets - Break Mandrel Type

2013-04-15

HISTORICAL

J1200_201304

This SAE Standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly.

Standard

Blind Rivets—Break Mandrel Type

1998-05-01

HISTORICAL

J1200_199805

This SAE Standard establishes the dimensional, mechanical, and performance requirements of inch and metric break mandrel blind rivets suitable for use in joining the component parts of an assembly.

Standard

Bolt and Capscrew Sizes for Use in Construction and Industrial Machinery

1998-05-01

HISTORICAL

J370_199805

This SAE Recommended Practice covers the use of preferred bolt and capscrew sizes, wherever applicable, on construction and industrial machinery to ease serviceability.

Standard

CONICAL SPRING WASHERS

1976-02-01

HISTORICAL

J773B_197602

This SAE Standard covers dimensional, material, and general specifications and methods of test for two types of general, purpose conical spring washers, designated type L and type H. for use as loose washers over screws and bolts, and also for use as pre-assembled washers in screw and washer assemblies.

Standard

CONICAL SPRING WASHERS

1976-02-01

HISTORICAL

J773_196106

This standard covers two types of general purpose conical spring washers, designated as Type L and Type H, for use as loose washers over screws and bolts, and also for use as preassembled washers on washer and screw or bolt assemblies. The Type L series is for use on screw or bolt assemblies having an ultimate strength range of 50,000 to 69,000 psi, and the Type H series is for use on screw or bolt assemblies having an ultimate strength in the area of 120,000 psi. The specification of sizes and types in this SAE Standard does not necessarily indicate that all sizes and types are available from stock. Users should consult with manufacturers for availability.

Standard

CONICAL SPRING WASHERS

1998-05-01

HISTORICAL

J773_199805

This SAE Standard covers dimensional, material, and general specifications and methods of test for two types of general purpose conical spring washers, designated type L and type H, for use as loose washers over screws and bolts, and also for use as pre-assembled washers in screw and washer assemblies.

Standard

CROWN (BLIND, ACORN) NUTS

1993-09-01

HISTORICAL

J483_199309

Included in this SAE Recommended Practice are complete general and dimensional data for the high and low types of crown nuts recognized as SAE Standard. These nuts are primarily intended for application in automotive and other ground-based motor vehicles and industrial equipment to provide an ornamental or protective closure over end of bolts, studs, or screws.

Standard

CROWN (BLIND, ACORN) NUTS

1998-05-01

HISTORICAL

J483_199805

Included in this SAE Recommended Practice are complete general and dimensional data for the high and low types of crown nuts recognized as SAE Standard. These nuts are primarily intended for application in automotive and other ground-based motor vehicles and industrial equipment to provide an ornamental or protective closure over end of bolts, studs, or screws.

Standard

Conical Spring Washers

2016-08-31

CURRENT

J773_201608

This SAE Standard covers dimensional, material, and general specifications and methods of test for two types of general purpose conical spring washers, designated type L and type H, for use as loose washers over screws and bolts, and also for use as pre-assembled washers in screw and washer assemblies.

Standard

Cotter Pins

1990-01-01

CURRENT

J487_199001

Not available.

Standard

DECARBURIZATION IN HARDENED AND TEMPERED METRIC THREADED FASTENERS

1996-08-01

HISTORICAL

J121M_199608

This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

DECARBURIZATION IN HARDENED AND TEMPERED METRIC THREADED FASTENERS

1997-04-01

HISTORICAL

J121M_199704

This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

DECARBURIZATION IN HARDENED AND TEMPERED METRIC THREADED FASTENERS

1994-05-26

HISTORICAL

J121M_199405

This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

DECARBURIZATION IN HARDENED AND TEMPERED THREADED FASTENERS

1983-08-01

HISTORICAL

J121_198308

This recommended practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

DECARBURIZATION IN HARDENED AND TEMPERED THREADED FASTENERS

1976-07-01

HISTORICAL

J121A_197607

This recommended practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.

Standard

DECARBURIZATION IN HARDENED AND TEMPERED UNIFIED THREADED FASTENERS

1997-04-01

HISTORICAL

J121_199704

This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.