Search Results

Materials with appropriate behavior at high temperatures and aggressive environments have become a scientific and technological necessity nowadays. Studies have been undertaken for improvement in getting new alloys, especially for the reevaluation of existing commercial alloys, through the acquisition of data under conditions of higher severity. In this context it was used for this work to Ti-6Al-4V in the form of cylindrical bars, provided forged and annealed at 190°C for 6 hours and cooled in air, which has favorable properties for aerospace application. The alloy after heat treatments to obtain the bimodal structures, martensite and Widmanstätten was subjected to creep tests at 600°C under the conditions of 250 and 319 MPa, in the form of constant load. The structures of Widmanstätten and martensite showed higher creep resistance in both stress conditions used in the trials.

The diamond thin films chemical vapor deposition (CVD) on sintered tungsten carbide (WC-Co) tools shows increasing interest in the technological research, due to rapid growing utilization of aluminum alloys, like Al-Si alloys, in the automotive industry. Sintered carbides, mainly diamond coated sintered carbides, are very suitable to machine aluminum alloys. The cobalt binder that accounts for the WC-Co substrate toughness degrades the interface film-substrate, catalyzing the formation of graphite preferentially to diamond during the deposition process. In addition, stresses are generated in the interface between WC-Co substrate and deposited diamond film due to thermal expansion mismatch. These two factors are a technological neck to large-scale production of diamond CVD coatings for machining tools. In this work, several interface pre-treatments were developed and applied resulting in high film-substrate adherence, adequate for machining tool purposes.

The aim of this paper is to analyze the microstructural development in samples of Ti-48Al-2Cr-2Nb (at.%) alloys obtained by powder metallurgy (P/M). This alloy has potential applications when high operating temperatures are required, e. g. turbines, aerospace applications, automotive engines valves and turbocharger rotors. The elementary powders were mixed for 1 hour, cold uniaxially pressed at 60 MPa and sintered at 1100°C, for 1 hour, under vacuum. Then, the specimens were milled and submitted to a second stage that included cold isostatic pressing (400 MPa) with subsequent hot uniaxial pressing (20 MPa), between 900 up to 1200°C, for 2 hours, in argon atmosphere. The alloys were characterized by XRD (X-ray diffraction), SEM (Scanning Electron Microscopy), EDS (Energy Dispersive Spectroscopy) and Vickers microhardness measurements. The results indicated the viability of the route and the tendency of a lamellar microstructure in high sintering temperatures.

In this work five methods of heat treatments are investigated in order to obtained convenient volume fractions of ferrite, bainite, martensite and retained austenite, starting with a low carbon steel and seeking the distinction of the phases, through optical microscopy. Specific chemical etching is improved. The results in tensile and fatigue tests were accomplished and the results were related with the microstructural parameters. The results show that the mechanical properties are closely related with the phases, grains size and the phases morphology.

In the present work we study the static indentation, i.e., the formation of small dents which result from laboratory tests specifically developed with this purpose. A mathematical model will be presented. It is based on the numerical and experimental tests performed with previous adjustment of all the mechanical variables involved. This model considers the test specimen and indentator geometry, the sheet anisotropic condition, the sheet's plasticity, and the contact conditions between the plate and the indentator developed. There is a goal to satisfy: specific requirements of a consumer market which is continuously willing for the development of materials with thinner thickness and better mechanical properties. To reach this goal, high strength steels manufactured by the SCAL (Sheet Continuous Annealing Line) are already been produced and tested in experimental scale. These bake-hardening steels can be used to manufacture external panels in the automobile industry.

The automotive industry has identified several automobile components that could be replaced with titanium alloy components, either through direct replacement in existing designs or, preferably, in new designs to fully exploit the unique properties of titanium. The alloy processing by powder metallurgy (M/P) eases the obtainment of parts with complex geometry and, probably, cheaper. In this work, results of the Ti-35Zr-10Nb alloy production are presented. This alloy due to its high wear, impact and corrosion resistance is a promising candidate for automotive applications. Samples were produced by mixing of initial metallic powders followed by uniaxial and cold isostatic pressing with subsequent densification by sintering between 900-1400 °C, in vacuum. Sintering behavior was studied by means of dilatometry. Sintered samples were characterized for phase composition, microstructure and microhardness by X-ray diffraction, scanning electron microscopy and Vickers indentation, respectively.