Search Results

The methodology for predicting the transient mixing rate is presented for a direct injection, quiescent chamber diesel. The mixing process is modeled as a zero-dimensional, large-scale phenomena which accounts for injection rate, cylinder geometry, and engine operating condition. As a demonstration, two different injection schemes were investigated for engine speeds of 1600, 2100, and 2600 rpm. In the first case, the air-fuel ratio was fixed while the injection rate was allowed to vary, but for the second case, the injection duration was fixed and the air-fuel ratio was allowed to vary. For the former case, the resulting mixing rate was also compared with the experimentally determined fuel burning rate. These two quantities appeared to be correlated in some manner for the various engine speeds under investigation.

Since the early inception of the adiabatic diesel engine in 1974, marked progress has taken place as a result of research efforts performed all over the world. The use of ceramics for heat engines in production applications has been limited to date, but is growing. Ceramic use for production heat engine has included: combustion prechambers, turbochargers, exhaust port liners, top piston ring inserts, glow plugs, oxygen sensors; and additional high temperature friction and wear components. The potential advantages of an adiabatic engine vary greatly with specific application (i.e., commercial vs. military, stationary vs. vehicular, etc.), and thus, a better understanding of the strengths and weaknesses (and associated risks) of advanced adiabatic concepts with respect to materials, tribology, cost, and payoff must be obtained.

The objective of this work is to develop a strategy to reduce the penalties in the diesel engine performance, fuel economy and HC and CO emissions, associated with the operation in the low temperature combustion regime. Experiments were conducted on a research high speed, single cylinder, 4-valve, small-bore direct injection diesel engine equipped with a common rail injection system under simulated turbocharged conditions, at IMEP = 3 bar and engine speed = 1500 rpm. EGR rates were varied over a wide range to cover engine operation from the conventional to the LTC regime, up to the misfiring point. The injection pressure was varied from 600 bar to 1200 bar. Injection timing was adjusted to cover three different LPPCs (Location of the Peak rate of heat release due to the Premixed Combustion fraction) at 10.5° aTDC, 5 aTDC and 2 aTDC. The swirl ratio was varied from 1.44 to 7.12. Four steps are taken to move from LTC to ALTC.

Signals indicative of in-cylinder combustion have been under investigation for the control of diesel engines to meet stringent emission standards and other production targets in performance and fuel economy. This paper presents the results of an investigation on the use of the ion current signal for the close loop control of a heavy duty four cylinder turbocharged diesel engine equipped with a common rail injection system. A correlation is developed between the start of ion current signal (SIC) and the location of the peak of premixed combustion (LPPC) in the rate of heat release trace. Based on this correlation, a PID closed loop controller is developed to adjust the injection timing for proper combustion phasing under steady and transient engine operating conditions.

JP-8 is an aviation turbine engine fuel recently introduced for use in military ground vehicle applications and generators which are mostly powered by diesel engines. Many of these engines are designed and developed for commercial use and need to be adapted for military applications. This requires more understanding of the auto- ignition and combustion characteristics of JP-8 under different engine operating conditions. This paper presents the results of a comparative analysis of an engine operation using JP-8 and ultra low sulfur diesel fuel (ULSD). Experiments were conducted on 0.42 liter single cylinder, high speed direct injection (HSDI) diesel engine equipped with a common rail injection system. The results indicate that the distillation properties of fuel have an effect on its vaporization rate. JP-8 evaporated faster and had shorter ignition delay as compared to ULSD. The fuel economy with JP-8 was better than ULSD.

The successful design of engine components for high temperature applications is very dependent on the use of advanced finite element methods. Without the use of thermal and structural modeling techniques it is virtually impossible to establish the reliable design specifications to meet the application requirements. Advanced modeling and design of two key engine components, the cylinder head thermal insulating headface plate and the capped air gap insulated piston, are presented. Prior engine test experience contributes to further understanding of the important factors in recognizing successful design solutions. It has been found that the modeling results are only as good as the modeling assumptions and that all modeling boundary conditions and constraints must be reviewed carefully.

The focus of this study is to determine the effect of using B-20 (a blend of 20% soybean methyl ester biodiesel and 80% ultra low sulfur diesel fuel) on the combustion process, performance and exhaust emissions in a High Speed Direct Injection (HSDI) diesel engine equipped with a common rail injection system. The engine was operated under simulated turbocharged conditions with 3-bar indicated mean effective pressure and 1500 rpm engine speed. The experiments covered a wide range of injection pressures and EGR rates. The rate of heat release trace has been analyzed in details to determine the effect of the properties of biodiesel on auto ignition and combustion processes and their impact on engine out emissions. The results and the conclusions are supported by a statistical analysis of data that provides a quantitative significance of the effects of the two fuels on engine out emissions.

The effect of biodiesel on the Particulate emissions is gaining significant attention particularly with the drive for the use of alternative fuels. The particulate matter (PM), especially having a diameter less than 50 nm called the Nanoparticles or Nucleation mode particles (NMPs), has been raising concerns about its effect on human health. To better understand the effect of biodiesel and its blends on particulate emissions, steady state tests were conducted on a small-bore single-cylinder high-speed direct-injection research diesel engine. The engine was fueled with Ultra-Low Sulfur Diesel (ULSD or B-00), a blend of 20% soy-derived biodiesel and 80% ULSD on volumetric basis (B-20), B-40, B-60, B-80 and 100% soy-derived biodiesel (B-100), equipped with a common rail injection system, EGR and swirl control systems at a load of 5 bar IMEP and constant engine speed of 1500 rpm.

The performance of the Common Rail diesel injection system (CRS) is investigated experimentally in a single cylinder engine and a test rig to determine the cycle-to-cycle variation in the injection pressure and its effects on the needle opening and rate of fuel delivery. The engine used is a single cylinder, simulated-turbocharged diesel engine. Data for the different injection and performance parameters are collected under steady state conditions for 35 consecutive cycles. Furthermore, a mathematical model has been developed to calculate the instantaneous fuel delivery rate at various injection pressures. The experimental results supported with the model computations indicated the presence of cycle-to-cycle variations in the fuel injection pressure and needle lift. The variations in the peak-cylinder gas pressure, rate of heat release, cylinder gas temperature and IMEP are correlated with the variation in the injection rate.

The effects of different blends of Soybean Methyl Ester (biodiesel) and ultra low sulfur diesel (ULSD) fuel: B-00 (ULSD), B-20, B-40, B-60, B-80 and B-100 (biodiesel); on autoignition, combustion, performance, and engine out emissions of different species including particulate matter (PM) in the exhaust, were investigated in a single-cylinder, high speed direct injection (HSDI) diesel engine equipped with a common rail injection system. The engine was operated at 1500 rpm under simulated turbocharged conditions at 5 bar IMEP load with varied injection pressures at a medium swirl of 3.77 w ithout EGR. Analysis of test results was done to determine the role of biodiesel percentage in the fuel blend on the basic thermodynamic and combustion processes under fuel injection pressures ranging from 600 bar to 1200 bar.

This paper investigates the effect of boost pressure and intake temperature on the auto-ignition of fuels with a wide range of properties. The fuels used in this investigation are ULSD (CN 45), FT-SPK (CN 61) and two blends of JP-8 (with CN 25 and 49). Detailed analysis of in-cylinder pressure and rate of heat release traces are made to correlate the effect of intake pressure and injection strategy on the events immediately following start of injection leading to combustion. A CFD model is applied to track the effect of intake pressure and injection strategy on the formation of different chemical species and study their role and contribution in the auto-ignition reactions. Results from a previous investigation on the effect of intake temperature on auto-ignition of these fuels are compared with the results of this investigation.

Significant progress has been achieved in the development of advanced high-temperature, insulated, in-cylinder components for high-power-output miliraty diesel engines. Computer aided modeling and small-bore engine component testing have both been utilized extensively during the exploratory development process. Specific insulated optimal designs for the piston, cylinder headface, and cylinder liner have been identified. The designs all utilize thermal barrier coatings, titanium alloy, and interfacial air-gaps to provide thermal resistance. Finite element modeling including diesel cycle simulation has been utilized to screen and optimize material and design concepts relative to program objectives, while small-bore engine testing has been utilized to demonstrate component integrity. An improved slurry densified thermal barrier coating has been demonstrated by testing on a high temperature small-bore engine.

This paper deals with the analysis of heat release characteristics of an insulated turbocharged, six cylinder, DI contemporary diesel engine. The engine is fully insulated with thin thermal barrier coatings. Effect of insulation on the heat release was experimentally verified. Tests were carried over a range of engine speeds at 100%, 93%, 75% and 50% of rated torque. Fuel injection system was instrumented to obtain injection pressure characteristics. The study shows that rate of heat release, particularly in the major portion of the combustion, is higher for the insulated engine. Improvement in heat release and performance are primarily attributed to reduction in heat transfer loss due to the thin thermal barrier coating. Injection pressure at the rated speed and torque was found to be 138 MPa and there was no degradation of combustion process in the insulated engine. Improvements in BSFC at 93% load are 3.25% and 6% at 1600 and 2600 RPM, respectively.

Thin thermal barrier ceramic coatings were applied to a standard production direct injection diesel engine. The resultant fuel economy when compared to the standard metallic engine at full load and speed (2600) was 6% better and 3.5% better at 1600 RPM. Most coated diesel engines todate have not shown significant fuel economy one way or the other. Why are the results more positive in this particular case? The reasons were late injection timing, high injection pressure with high injection rates to provide superior heat release rates with resultant lower fuel consumption. The recent introduction of the high injection pressure fuel injection system makes it possible to have these desirable heat release rates at the premixed combustion period. Of course the same injection characteristics were applied to the standard and the thin thermal barrier coating case. The thin thermal barrier coated engine displayed superior heat release rate.

An advanced design methodology is developed for innovative composite structure concepts which can be used in the Army's future ground vehicle systems to protect vehicle and occupants against various explosives. The multi-level and multi-scenario blast simulation and design system integrates three major technologies: a newly developed landmine-soil-composite interaction model; an advanced design methodology, called Function-Oriented Material Design (FOMD); and a novel patent-pending composite material concept, called BTR (Biomimetic Tendon-Reinforced) material. Example results include numerical simulation of a BTR composite under a blast event. The developed blast simulation and design system will enable the prediction, design, and prototyping of blast-protective composite structures for a wide range of damage scenarios in various blast events.

An integrated vehicle system simulation has been developed to take advantage of advances in physical process and component models, flexibility of graphical programming environments (such as MATLAB-SIMULINK), and ever increasing capabilities of engineering workstations. A comprehensive, transient model of the multi-cylinder engine is linked with models of the torque converter, transmission, transfer case and differentials. The engine model is based on linking the appropriate number of single-cylinder modules, with the latter being thermodynamic models of the in-cylinder processes with built-in physical sub-models and transient capabilities to ensure high fidelity predictions. Either point mass or multi-body vehicle dynamics models can be coupled with the powertrain module to produce the ground vehicle simulation.

A previous paper (1)* described the performance improvements which can be obtained by using an “adiabatic” (uncooled) engine for military trucks. The fuel economy improved 16% to 37% (depending upon the duty cycle) and was documented by dynamometer testing and vehicle testing and affirmed by vehicle simulation. The purpose of this paper is to document a NATO cycle 400 hour durability test which was performed on the same model adiabatic engine. The test results showed that the engine has excellent durability, low lubricating oil consumption and minimal deposits.

An investigation into the fuel economy of a U.S. Army M813 5-ton truck with an “adiabatic” (uncooled) 14 liter (855 in3) diesel engine was made with three different driving schedules. The results were used to verify a newly written vehicle simulation. This simulation was used to compare the fuel economy of an uncooled turbocharged engine, a water cooled turbocharged engine, and a water cooled naturally aspirated engine in the same vehicle. Results indicate that, depending on the duty cycle a 16% to 37% improvement in fuel economy (depending on the duty cycle) can be achieved with an uncooled engine in this vehicle.

Diesel engine cold-start problems include long cranking periods, hesitation and white smoke emissions. A better understanding of these problems is essential to improve diesel engine cold-start. In this study computer simulation model is developed for the steady state and transient cold starting processes in a single-cylinder naturally aspirated direct injection diesel engine. The model is verified experimentally and utilized to determine the key parameters that affect the cranking period and combustion instability after the engine starts. The behavior of the fuel spray before and after it impinges on the combustion chamber walls was analyzed in each cycle during the cold-start operation. The analysis indicated that the accumulated fuel in combustion chamber has a major impact on engine cold starting through increasing engine compression pressure and temperature and increasing fuel vapor concentration in the combustion chamber during the ignition delay period.

A large scale, high resolution, finite element methodology for analysis of generic thermomechanical behavior of complex, low heat rejection engine components has been developed. This paper describes this process and presents an example evaluation of a low heat rejection cylinder head. Because of symmetry considerations, a one cylinder section of the head was modeled. However, the geometric nature of this cylinder head section required very precise three-dimensional analysis techniques. The completed three-dimensional model contains 40,696 elements and 48,536 nodes. The results of this example model show high stresses at the valve bridge and injector bore. These stresses result from a constrained thermal expansion of the head, and are generally compressive and radial in nature. A comparison of three different material types indicated that two of the three exceeded, and one was below the elastic limit.