Search Results

This paper presents the results and conclusions from a conceptual design study for a stratified charging concept. The stratified charging engine has a displacement of 64 cm3 and a four-port design with reed valves at two ports to control the bypass air. During the intake stroke of the engine, bypass air is sucked into the transfer ports to purge the air-fuel mixture present in the ports from the previous stroke back into the crankcase. This fills the transfer ports near the exhaust with pure air at the beginning of the scavenging stroke. During scavenging, the bypass air is ejected in the cylinder, shielding the exhaust against the fresh mixture coming from the ports on the intake side. This allows the hydrocarbon emissions to be reduced by over 40 %. The conceptual design study is based on an analysis of the mixture short-circuiting mechanisms and CFD investigations of the scavenging flow with charge stratification.

This paper shows that the functional integration of Electronic Throttle Control (ETC) into the engine control strategy allows improvements of emissions and fuel economy without making compromises in respect of driveability. A cost effective way for realizing ETC is the integration of the control electronics into the engine control unit (ECU). The paper describes the consequences of such an integration for the ECU hardware and software. Special attention is given to the ETC related safety aspects. Another chapter discusses different technologies for the throttle actuator drive. This is followed by a brief description of a suitable control strategy for a throttle actuator. Finally the paper gives also an overview about current status and development trends of accelerator pedal sensors necessary for ETC.

This paper describes the exhaust emission control system designed for the new Mercedes-Benz sports car generation 300 SL and 500 SL, Remarkable features of the catalytic converters are maximum environmental compatibility, i. e. minimum of emission and noise under all driving conditions. By reduced back-pressure, they also contribute greatly to the well known requirements of a sports car: high performance and high torque over the entire engine-speed-range. Apart from an effective exhaust gas aftertreatment, great efforts were made to prevent the formation of pollutants under all driving conditions. This work is done by intelligent motor management consisting of digital spark control, mechanical-electronic injection, variable valve timing and EGR.

This paper reviews the current and new engine technologies that are suitable to be implemented in light-weight outdoor power equipment that is mostly powered by two-stroke engines. It gives insight in the concerns associated with the improvement of known technologies and highlights trends for future engine developments. Among others, the paper covers ways for the conventional scavenging improvement, catalyst development, low pressure mixture injection, direct fuel injection, stratified scavenging and also four-stroke technology. These concepts are assessed with respect to performance, cost, size and weight. Special emphasis is laid on the research and development of a catalyst concept for high-performance two-strokes and direct fuel injection. The catalyst is one of the easiest and most effective ways for emission reduction. However, measures have to be found to overcome the severe thermal difficulties.

The new Mercedes-Benz sportscars typify European catalytic converter design trends. Maximum frontal-area for minimum back-pressure and maximum power of the 4-valve engine was the target for the new 300 SL. This was achieved by moving away from conventional design and using a shape of substrate and housing equidistant to the contour of the transmission-tunnel. Great efforts had to be done to give necessary mechanical strength to the system, but as a result there is a big improvement in engine power and catalytic longterm stability. New canning technology, based upon mat, has been utilised for the 300 CE. A lot of engineering ideas were necessary to develop a so-called “high-tech” variant of the mat-canning system, which fulfills all the demands without any defects, especially under European driving conditions. Apart from economy of space, additional advantages of the new converter, compared with wire-mesh systems, include lower external surface temperature and less noise.

Secondary air injection after cold start gives two effects for reduced exhaust emissions: An exothermic reaction at the hot exhaust valves occurs, which increases the temperature of the exhaust gas. It gives sufficient air to the catalyst during the cold start fuel enrichment that is necessary to prevent driveability problems. Handicaps for the wide use of air injection include space constraints, weight and price. An electrical air blower was choosen to best satisfy all these requirements. The development steps are described. The result is a three stage radialblower with extremly high revolutions of about 18000 rpm. The system configuration and the outcome are demonstrated on the new C-Class of Mercedes-Benz. The results show emission reductions higher than 50 %, while also satisfying the development goals of noise, volume, weight and cost requirements.