Criteria

Text:
Display:

Results

Viewing 1 to 30 of 2620
WIP Standard
2014-07-21
General Agreement Ballot will simplify the decarburization requirements of flat rolled products to that of the bar products and will eliminate the step procedure.
WIP Standard
2014-07-18
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable specification requirements of carbon and low-alloy steel forgings.
Standard
2014-07-17
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
Standard
2014-07-17
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
Standard
2014-07-17
This specification covers an aircraft-quality, low-alloy steel in the form of seamless tubing. This tubing has been used typically for thin wall-thickness sections where minimum tensile strength up to 160 ksi (1103 MPa) is required and where parts may be welded during fabrication, but usage is not limited to such applications.
Standard
2014-06-05
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, flash welded rings, and stock for forging or flash welded rings.
Standard
2014-06-05
This specification covers an aircraft-quality, low-alloy steel in the form of round, seamless tubing having a wall thickness not greater than 0.188 inch (4.78 mm). This tubing has been typically used in thin-walled sections where a minimum tensile strength of 125 ksi (862 MPa) is required, but usage is not limited to such applications.
Standard
2014-06-05
This specification covers an aircraft-quality, low-alloy steel in the form of round, seamless tubing having a wall thickness not greater than 0.188 inch (4.78 mm). This tubing has been used typically for general use where a minimum tensile strength of 150 ksi (1034 MPa) is required, but usage is not limited to such applications.
Standard
2014-06-05
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable specification requirements of carbon and low-alloy steel forgings.
Standard
2014-05-19
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
Standard
2014-05-14
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
WIP Standard
2014-04-27
This specification covers an aircraft-quality, low-alloy steel in the form of sheet, strip, and plate.
WIP Standard
2014-04-27
This specification covers an aircraft-quality, low-alloy steel in the form of sheet, strip, and plate.
WIP Standard
2014-04-27
This specification covers an aircraft-quality, low-alloy steel in the form of sheet, strip, and plate.
WIP Standard
2014-04-27
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable specification requirements of wrought carbon and low-alloy steel products and of forging stock.
WIP Standard
2014-04-27
This specification covers an aircraft-quality, low-alloy steel in the form of sheet, strip, and plate.
WIP Standard
2014-04-27
This specification covers an aircraft-quality, low-alloy steel in the form of sheet, strip, and plate.
WIP Standard
2014-04-27
This specification covers an aircraft-quality, low-alloy steel in the form of sheet, strip, and plate.
WIP Standard
2014-04-10
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.

These products have been used typically for bearing component requiring a through-hardening steel usually with hardness of approximately 60 HRC and section thickness under 0.50 in. (12.7 mm).

WIP Standard
2014-04-10
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
WIP Standard
2014-04-10
A steel grade with improved properties compared to 300M (UTS>300ksi)
WIP Standard
2014-04-10
This specification covers a low-alloy steel in the form of welding wire.

This wire has been used typically for use as filler metal for gas-tungsten-arc and gas-metal-arc welding of low-alloy steels of similar composition where the weld area is required to have strength comparable to that of the parent metal, but usage is not limited to such applications.

WIP Standard
2014-04-10
This specification covers a free-machining, low-alloy steel in the form of round bars 3.50 inches (88.9 mm) and under in nominal diameter.

These bars have been used typically for parts, such as shafts, axles, pins, fasteners, gears, and screw machine parts, which are normally used at hardness of 30 to 36 HRC and which do not require a high degree of ductility, but usage is not limited to such applications.

WIP Standard
2014-04-10
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, and forging stock.
WIP Standard
2014-04-10
This specification covers an aircraft-quality, low-alloy steel in the form of sheet, strip, and plate.
WIP Standard
2014-04-10
This specification covers a low-alloy steel in the form of welding wire.

This wire has been used typically as filler metal for gas-tungsten-arc and gas-metal-arc welding of low-alloy steels where the joint is capable of being heat treated to a minimum tensile strength up to 180 ksi (1241 MPa), but usage is not limited to such applications.

WIP Standard
2014-04-10
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, flash welded rings, and stock for forging or flash welded rings.
WIP Standard
2014-04-10
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.

These products have been used typically for parts, 0.750 inch (19.05 mm) and under in section thickness at time of heat treatment, requiring a through-hardening steel capable of developing hardness as high as 50 HRC when properly hardened and tempered and also parts of greater thickness but requiring proportionately lower hardness, but usage is not limited to such applications.

WIP Standard
2014-03-07
This specification covers an aircraft quality, low alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. These products have been used typically for parts requiring a combination of high tensile strength and good ductility with relatively high impact strength and hardness, but usage is not limited to such applications. Certain design and processing procedures may cause these products to become susceptible to stress-corrosion cracking after heat treatment. ARP1110 recommends practices to minimize such conditions.
WIP Standard
2014-03-07
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
Viewing 1 to 30 of 2620

Filter

  • Range:
    to:
  • Year: