Refine Your Search

Topic

Search Results

Standard

Aerospace Size Standard for O-rings

2014-03-11
CURRENT
AS568D
This SAE Aerospace Standard (AS) specifies the inside diameters, cross-sections, tolerances, and size identification codes (dash numbers) for O-rings used in sealing applications and for straight thread tube fitting boss gaskets. The dimensions and tolerances specified in this standard are suitable for any elastomeric material provided that suitable tooling is available.
Standard

O-Ring Molded from AMS7274 Material

2020-01-09
CURRENT
AS3570A
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for O-rings molded from AMS7274 rubber. It shall be used for procurement purposes.
Standard

O-Ring Molded from AMS7267 Material

2020-01-09
CURRENT
AS9386A
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for O-rings molded from AMS7267 rubber. It shall be used for procurement purposes.
Standard

O-Ring Molded from AMS7273 Material

2020-01-09
CURRENT
AS9967A
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for O-rings molded from AMS7273 rubber. It shall be used for procurement purposes.
Standard

O-Ring Machined from AMS3617 Material

2020-01-13
CURRENT
AS9772A
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for O-rings machined from AMS3617 polyamide material. It shall be used for procurement purposes.
Standard

Sealing Techniques for Missile Applications

2001-01-01
HISTORICAL
ARP1833A
The purpose of this standard is to provide the missile hydraulic and pneumatic component designer with information learned, tested and substantiated in correction of problems and failures experienced with seals that are subject to the unique requirements of missile static storage and subsequent dynamic operational conditions. Missile hydraulic and pneumatic component designers have been handicapped by the absence of concise design criteria for two difficult sealing conditions usually existing in missile applications as follows: Static pressure condition - Low pressure for long periods in a cyclic temperature environment (i.e., long term storage requirements). Dynamic pressure condition - High pressures suddenly applied in an extreme temperature environment (i.e., operational firing requirement).
Standard

Gland Design, O-ring and Other Elastomeric Seals, Static Applications

2010-11-29
CURRENT
AS5857A
This SAE Aerospace Standard (AS) provides standardized gland (groove) design criteria and dimensions for elastomeric seal glands for static applications. The glands have been specifically designed for applications using SAE AS568 size O-rings at pressures exceeding 1500 psi (10.3 MPa) utilizing one or two anti-extrusion (backup) rings and applications at pressures under 1500 psi (10.3 MPa) without backup rings. The glands have been sized to provide increased squeeze as compared to AS4716 for more effective sealing at low temperatures and low seal swell conditions. These glands are not recommended for dynamic use. Primary usage is for static external sealing. The rod dimensions are the same as AS4716. The cylinder bore dimensions are the same as AS4716 except for sizes -001 thru -011 and -104 thru -113.
Standard

Gland Design, O-ring and Other Elastomeric Seals, Static Applications

2005-03-30
HISTORICAL
AS5857
This SAE Aerospace Standard (AS) provides standardized gland (groove) design criteria and dimensions for elastomeric seal glands for static applications. The glands have been specifically designed for applications using SAE AS568 size O-rings at pressures exceeding 1500 psi (10.3 MPa) utilizing one or two anti-extrusion (backup) rings and applications at pressures under 1500 psi (10.3 MPa) without backup rings. The glands have been sized to provide increased squeeze as compared to AS4716 for more effective sealing at low temperatures and low seal swell conditions. These glands are not recommended for dynamic use. Primary usage is for static external sealing. The rod dimensions are the same as AS4716. The cylinder bore dimensions are the same as AS4716 except for sizes -001 thru -011 and -104 thru -113.
X