Refine Your Search

Topic

Search Results

Standard

Treatment of Sheet Metal Parts Corrosion-Resistant Steel

2017-09-20
CURRENT
AMS2550F
This specification covers the engineering requirements for a treatment to provide enhanced corrosion resistance to sheet metal parts, such as brackets, spacers, and washers, fabricated from martensitic Corrosion-resistant steels, usually AMS 5504 or AMS 5508 and having hardness not higher than 40 HRC, or ferritic corrosion-resistant steels, usually AMS 5506. The treatment is not recommended for use on parts subject to impact in service.
Standard

Treatment of Sheet Metal Parts Corrosion-Resistant Steel

1994-03-01
HISTORICAL
AMS2550E
This specification covers the engineering requirements for a treatment to provide enhanced corrosion resistance to sheet metal parts, such as brackets, spacers, and washers, fabricated from martensitic Corrosion-resistant steels, usually AMS 5504 or AMS 5508 and having hardness not higher than 40 HRC, or ferritic corrosion-resistant steels, usually AMS 5506. The treatment is not recommended for use on parts subject to impact in service.
Standard

Training and Approval of Heat-Treating Personnel

1995-12-01
HISTORICAL
ARP1962A
This document requires that the company (facility) employing the personnel ensure a verifiable program of on-the-job training, experience, education, classroom instruction, and evaluation of personnel using either company-created programs or programs described herein.
Standard

Training and Approval of Heat-Treating Personnel

2019-06-11
CURRENT
ARP1962B
This SAE Aerospace Recommended Practice (ARP) describes training and approval of personnel performing certain heat-treating and associated operations that could have a material impact on the properties of materials being heat treated. It also recommends that only approved personnel perform or monitor the functions listed in Table 1.
Standard

The Pre-Treatment and Protection of Steel Items of Specified Maximum Tensile Strength Exceeding 1450 MPa

2017-03-21
CURRENT
AMS03_4A
This SAE Standard specifies the special treatments and precautions that are to be observed when protective and other surface treatments are applied to items, including springs, made from steel of specified maximum tensile strength exceeding 1450 MPa. The requirements of this Standard qualify those in process specifications and override the latter where there is conflict. The Standard also gives advice on design, manufacture, and preparation of items prior to cleaning and protection.
Standard

The Pre-Treatment and Protection of Steel Items of Specified Maximum Tensile Strength Exceeding 1450 MPa

2015-04-27
HISTORICAL
AMS03_4
This SAE Standard specifies the special treatments and precautions that are to be observed when protective and other surface treatments are applied to items, including springs, made from steel of specified maximum tensile strength exceeding 1450 MPa. The requirements of this Standard qualify those in process specifications and override the latter where there is conflict. The Standard also gives advice on design, manufacture, and preparation of items prior to cleaning and protection.
Standard

The Chemical Milling Process

2019-09-30
WIP
ARP1331C
This recommended practice provides recommendations concerning the chemical milling of aluminum, magnesium, and titanium alloys, and specialty alloys. The detailed recommendations are based on practical engineering and production experience that will enable industry to make proper use of the chemical milling process.
Standard

TUNGSTEN CARBIDE-COBALT COATING Detonation Process

1994-10-01
HISTORICAL
AMS2435E
This specification covers the engineering requirements for applying tungsten carbide/cobalt coatings to metal parts by the detonation process and the properties of such coatings.
Standard

TREATMENT OF SHEET METAL PARTS Steel Corrosion-Resistant

1976-07-01
HISTORICAL
AMS2550C
This specification covers the engineering requirements for a treatment to provide maximum attainable corrosion resistance to sheet metal parts, such as brackets, spacers, and washers, fabricated from martensitic corrosion-resistant steels, usually AMS 5504 or AMS 5508 and having hardness not higher than 40 HRC, or ferritic corrosion-resistant steels, usually AMS 5506. The treatment is not recommended for use on parts subject to impact in service.
Standard

TREATMENT OF SHEET METAL PARTS Corrosion-Resistant Steel

1992-04-01
HISTORICAL
AMS2550D
This specification covers the engineering requirements for a treatment to provide enhanced corrosion resistance to sheet metal parts, such as brackets, spacers, and washers, fabricated from martensitic corrosion-resistant steels, usually AMS 5504 or AMS 5508 and having hardness not higher than 40 HRC, or ferritic corrosion-resistant steels, usually AMS 5506. The treatment is not recommended for use on parts subject to impact in service.
Standard

TIN PLATING, IMMERSION

1991-10-01
HISTORICAL
AMS2409E
This specification covers the engineering requirements for producing a thin tin coating on aluminum alloys by an immersion process.
X