Refine Your Search

Topic

Search Results

Standard

Automatic Transmission Hydraulic Pump Test Procedure

2015-03-17
CURRENT
J2311_201503
This SAE Recommended Practice provides a method to determine the performance characteristics of the hydraulic oil pumps used in automatic transmissions and automatic transaxles. This document outlines the specific tests that describe the performance characteristics of these pumps over a range of operating conditions and the means to present the test data. This document is not intended to assess pump durability.
Standard

Engine Flywheel Housing and Mating Transmission Housing Flanges

2014-04-16
HISTORICAL
J617_201404
This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face. This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face or the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded. This document applies to any internal combustion engine which can utilize SAE No. 6 through SAE No. 00 size flywheel housing for mounting a transmission.
Standard

Automatic Transmission Intake Filter Test Procedure

2013-05-14
CURRENT
J2312_201305
This test procedure is intended to apply to hydraulic pump suction filters and strainers used in automotive automatic transmissions that include hydraulic power pumps. The various paragraphs of Section 5, “Test Procedures,” include a variety of tests and alternative tests that are not applicable to all filters and applications, so the engineer must specify which tests are to be performed for a particular application. These test procedures are intended to evaluate filter functional performance characteristics only, durability is not evaluated under this standard. Filter design requirements must be specified by the engineer on the filter assembly drawing, an applicable engineering specification, or summarized on an application data sheet similar to that found in this recommended practice. See Figure 6, “Filter Assembly Application and Data Sheet.” Pressure circuit filters, both barrier and system contamination control types, are not covered under this standard.
Standard

SAE No.2 Friction Test Machine 6000 r/min Stepped Power Test

2013-03-11
HISTORICAL
J2488_201303
This SAE Recommended Practice is intended as the definition of a standard test, but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The SAE No. 2 Friction Test Machine is used to evaluate the friction characteristics of automatic transmission plate clutches with automotive transmission fluids. It can also be used to conduct durability tests on wet friction systems. The specific purpose of this document is to define a 6000 r/min Stepped Power Test for the evaluation of wet friction system performance variation as a function of power level. This procedure uses an initial engagement speed of 6000 r/min and is intended as a standard procedure for common use by both suppliers and end users.
Standard

SAE No. 2 Friction Test Machine µPVT Test

2012-08-06
HISTORICAL
J2490_201208
This SAE Recommended Practice is intended as the definition of a standard test, which may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The SAE No. 2 Friction Test Machine is used to evaluate the friction characteristics of automatic transmission plate clutches with automotive transmission fluids. It can also be used to conduct durability tests on wet friction systems. The specific purpose of this document is to define a µPVT Test for the evaluation of the variation of wet friction system performance as a function of speed, temperature, and pressure. This procedure is intended as a standard for both suppliers and end users. The only variables selected by the supplier or user of the friction system are: a Friction Material b Fluid c Reaction Plates These three variables must be clearly identified when reporting the results of this test.
Standard

Flywheels for Engine-Mounted Torque Converters

2012-06-11
CURRENT
J927_201206
This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for engine flywheel mounted torque converters. Tables 1A and 1B and Figure 1 give dimensions for flywheels mounted-type torque converters. For torque converters using drive ring overcenter type disconnect clutch, see SAE J620.
Standard

Hydrodynamic Drives Terminology

2012-06-04
HISTORICAL
J641_201206
Since the torque converter and fluid coupling are commonly used components of automatic transmissions in industry, the SAE appointed a committee to standardize terminology, test procedure, data recording, design symbols, and so forth, in this field. The following committee recommendations will facilitate a clear understanding for engineering discussions, comparisons, and the preparation of technical papers. The recommended usages represent the predominant practice or the acceptable practice. Where agreement is not complete, alternates have been included for clarification. This SAE Recommended Practice deals only with the physical parts and dimensions and does not attempt to standardize the design considerations, such as the actual fluid flow angle resulting from the physical blade shape.
Standard

SAE No. 2 Friction Test Machine 3600 r/min Stepped Power Test

2012-05-31
HISTORICAL
J2487_201205
This SAE Recommended Practice is intended as the definition of a standard test, but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The SAE No. 2 Friction Test Machine is used to evaluate the friction characteristics of automatic transmission plate clutches with automotive transmission fluids. It can also be used to conduct durability tests on wet friction systems. The specific purpose of this document is to define a 3600 r/min Stepped Power Test for the evaluation of wet friction system performance variation as a function of power level. This procedure uses an initial engagement speed of 3600 r/min and is intended as a standard procedure for common use by both suppliers and end users.
Standard

Engine Flywheel Housing and Mating Transmission Housing Flanges

2012-05-31
HISTORICAL
J617_201205
This SAE Standard specifies the major dimensions and tolerances for Engine Flywheel Housings and the Mating Transmission Housing Flanges. It also locates the crankshaft flange face or the transmission pilot bore (or pilot bearing bore) stop face in relation to housing SAE flange face. This document is not intended to cover the design of the flywheel housing face mating with the engine crankcase rear face of the design of housing walls and ribs. Housing strength analysis and the selection of housing materials are also excluded. This document applies to any internal combustion engine which can utilize SAE No. 6 through SAE No. 00 size flywheel housing for mounting a transmission.
Standard

SAE Band Friction Test Machine Guidelines

2012-03-19
CURRENT
J1499_201203
This SAE Recommended Practice is intended as a guide toward implementation of a standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The SAE band friction test machine is used to evaluate the frictional characteristics of automatic transmission band friction materials with automatic transmission fluids. It can also be used to conduct durability tests on wet friction systems.
Standard

SAE No. 2 Friction Test Machine Durability Test

2012-03-19
CURRENT
J2489_201203
This SAE Recommended Practice is intended as the definition of a standard test, but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The SAE No 2 Friction Test Machine is used to evaluate the friction characteristics of automatic transmission plate clutches with automotive transmission fluids. It can also be used to conduct durability tests on wet friction systems. The specific purpose of this document is to define a Durability Test based on a specific power level selected from either the 3600 r/min Stepped Power Test or from the 6000 r/min Stepped Power Test, for the evaluation of wet friction system performance variation as a function of number of cycles. This standard procedure is intended for common use by both suppliers and end users to allow objective comparisons of wet friction material system performance.
Standard

SAE No. 2 Clutch Friction Test Machine Guidelines

2012-03-19
CURRENT
J286_201203
This SAE Recommended Practice is intended as a guide toward implementation of a standard practice but may be subject to frequent change to keep pace with experience and technical advances. This should be kept in mind when considering its use. The SAE No. 2 Friction Test Machine is used to evaluate the friction characteristics of automatic transmission plate clutch with automotive transmission fluids. It can also be used to conduct durability tests on wet friction systems. This document is intended for common use by both suppliers and end users to define minimum test machine requirements to allow objective comparisons of wet friction material system performance.
Standard

Glossary of Terms - Lubricated Friction Systems

2012-03-19
CURRENT
J1646_201203
This SAE Recommended Practice defines the principal terms and equations pertaining to automotive automatic transmission clutch plate, band, or other wet-friction systems. The terms apply directly to friction-system testing as is typically conducted on inertia-stop test equipment. Some terms can be directly applied to the analysis of friction in the transmission or brake assembly and other friction-test equipment. The glossary presents terms used to describe the set-up, testing, and results of tests as shown in Figure 1, which were taken on a clutch SAE No. 2 machine. The glossary is intended to provide a collection of definitions in the hope of eliminating confusion in development and their application to passenger cars and trucks. This document focuses on the terminology of friction-system testing. References for this type of testing are shown in Section 2.
Standard

One-Way Clutches - Nomenclature and Terminology

2011-08-12
HISTORICAL
J1087_201108
The definitions and illustrations in this SAE Recommended Practice are intended to establish common nomenclature and terminology for automotive transmission one-way clutches.
Standard

Symbols for Hydrodynamic Drives

2011-07-08
CURRENT
J640_201107
The following system of symbols is recommended for use in technical papers and engineering reports dealing with hydrodynamic drives.
Standard

Rectangular Cross Section Polymeric Sealing Rings

2011-05-02
HISTORICAL
J2310_201105
The purpose of this SAE Recommended Practice is to establish guidelines for the automatic transmission and hydraulic systems engineer to design rectangular cross section seals for rotating and static grooved shaft applications. Also included are property comparisons of polymeric materials suitable for these applications. Historically, material covered in this document is not intended to include aluminum contact applications.
Standard

Fatigue LIfe Procedure for Wet Friction Materials

2011-04-05
WIP
J2968
This specification would cover standards for performing wet friction material fatigue life determination. It would include recommendations on equipment, sample preparation, and results reporting
Standard

Hydrodynamic Drive Test Code

2011-04-04
HISTORICAL
J643_201104
The range of test conditions on the dynamometer shall be sufficient to determine the primary operating characteristics corresponding to the full range of vehicle operations. The characteristics to be determined are: a Torque ratio versus speed ratio and output speed b Input speed versus speed ratio and output speed c Efficiency versus speed ratio and output speed d Capacity factor versus speed ratio and output speed e Input torque versus input speed NOTE: For more information about these characteristics and the design of hydrodynamic drives, see “Design Practices—Passenger Car Automatic Transmissions,” SAE Advances in Engineering, AE18 or AE29
Standard

Planetary Gears - Terminology

2011-04-04
HISTORICAL
J646_201104
Figures 1 to 5 illustrate in simplified form some of the more common planetary gear arrangements in order to establish applicable terminology. Gear ratio is the numerical ratio of input to output speed.
Standard

Automatic Transmissions - Schematic Diagrams

2010-04-23
HISTORICAL
J647_201004
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
X