Refine Your Search

Topic

Search Results

Standard

Snowmobile Probe Test for Contact with Power Driven Parts

2016-02-18
CURRENT
J2826_201602
This SAE Recommended Practice establishes the test equipment, procedure, and acceptance criteria necessary to determine the location of power driven components that could, upon inadvertent contact by an operator, passenger, or bystander, inflict injury.
Standard

Snowmobile Passenger Handgrips

2016-01-20
WIP
J1062
This SAE Recommended Practice is intended to give information to engineers and designers in order that access to a passenger handgrip, when used, is easily obtained and that such handgrips offer maximum safety for a person at least as large as a 95th percentile adult male during snowmobile operation.
Standard

Measurement of Exhaust Sound Levels of Stationary Snowmobiles

2015-11-24
CURRENT
J2567_201511
This SAE Recommended Practice establishes the test procedure, environment and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
Standard

Stationary Sound Testing of Snowmobiles, Procedure and Enforcement Issues

2015-11-24
CURRENT
J2641_201511
This SAE Information Report provides basic information about the issues surrounding the administration of stationary, infield sound testing of snowmobiles. The information provided herein is meant to enhance safety, improve the environment and promote uniform testing.
Standard

Recommendations for Children's Snowmobile

2015-11-24
CURRENT
J1038_201511
This SAE Recommended Practice establishes the test procedures, performance requirements, and criteria necessary to evaluate minimum safety and reliability requirements of a children's snowmobile as identified in 1.2.
Standard

Speed Control Assurance for Snowmobiles

2014-08-21
CURRENT
J1222_201408
This SAE Recommended Practice provides minimum requirements and performance criteria for devices to prevent runaway snowmobiles due to malfunction of the speed control system.
Standard

Snowmobile Fuel Tanks

2014-04-16
CURRENT
J288_201404
To provide minimum performance requirements for non-pressurized fuel tanks used on snowmobiles as defined in SAE J33.
Standard

Dynamic Cushioning Performance Criteria for Snowmobile Seats

2014-04-09
HISTORICAL
J89_201404
This SAE Recommended Practice encompasses the significant factors which determine the effectiveness of a seat system in limiting spinal injury during vertical impacts between the rider and the snowmobile seat system. The document is intended to provide a tool for the development of safer snowmobile seats. It is recognized that the seat is only a portion of the entire vehicle protective suspension system. It is, however, usually required that the seat serve as added protection to the suspension system, since the latter may "bottom out" during a severe impact. The term "seat" refers to the occupant-supporting system not normally considered part of the vehicle suspension or frame system. In some cases, it may include more than the foam cushion.
Standard

Maximum Exterior Sound Level for Snowmobiles

2013-01-10
HISTORICAL
J192_201301
This SAE Recommended Practice establishes the instrumentation, test site, and test procedure for determining the maximum exterior sound level for snowmobiles. Sound propagation is directly related to the ground cover and provides the largest variation to the measured result. A correction factor is introduced to improve year round test repeatability of the results on grass surfaces by correcting their spectrum to be similar to snow covered spectra. Measured sound pressure levels are also highly dependent on the degree of track slip present when performing the vehicle acceleration. Operators should attempt to limit track slip as much as possible while maintaining the requirements described in 5.1.1.
Standard

Snowmobile Brake Control Systems

2012-04-09
HISTORICAL
J1282_201204
This SAE Recommended Practice is intended to provide the minimum acceptable criteria for snowmobile hand brake control systems. This recommendation is not intended to cover competition vehicles nor is it intended to limit development of new and/or improved technology in controls. Although these recommendations are primarily addressed to hand control systems using an outer flexible conduit with a multiple strand inner cable or hydraulic type brake control system, the basic requirements of freedom of movement, strength, material, etc., will apply to any system.
Standard

Speed Control Assurance for Snowmobiles

2012-03-12
HISTORICAL
J1222_201203
This SAE Recommended Practice provides minimum requirements and performance criteria for devices to prevent runaway snowmobiles due to malfunction of the speed control system.
Standard

Snowmobile Headlamps

2011-03-12
CURRENT
J280_201103
This standard provides test methods and requirements for snowmobile headlamps.
Standard

Snowmobile Stop Lamp

2011-03-12
CURRENT
J278_201103
This document provides test methods and requirements for the stop lamp on snowmobiles.
Standard

Maximum Exterior Sound Level for Snowmobiles

2011-03-06
HISTORICAL
J192_201103
This SAE Recommended Practice establishes the instrumentation, test site, and test procedure for determining the maximum exterior sound level for snowmobiles. Sound propagation is directly related to the ground cover and provides the largest variation to the measured result. A correction factor is introduced to improve year round test repeatability of the results on grass surfaces by correcting their spectra to be similar to snow covered ground spectrums. Measured sound pressure levels are also highly dependent on the degree of track slip present when performing the vehicle acceleration. Operators should attempt to limit track slip as much as possible while maintaining the requirements described in 5.1.1.
Standard

Snowmobile Drive Mechanisms

2010-08-26
HISTORICAL
J1279_201008
This SAE Recommended Practice is applicable to snowmobiles as defined in SAE J33.
X