Refine Your Search

Topic

Search Results

Standard

On-Highway Equipment Control and Communication Network

2019-02-13
WIP
J1939/1
SAE J1939-1 On-Highway Equipment Control and Communication Network specifies the minimum set of SAE J1939 documents that define the Truck and Bus Control and Communications Vehicle Network as it applies to on-highway equipment. Vehicles covered include all on-highway straight trucks and combination vehicles. A combination vehicle consists of one towing vehicle (tractor) and one or more towed vehicles (trailers and dollies). Dolly axles within the road train are considered to be towed vehicles.
Standard

Compliance—Truck and Bus

2008-08-11
HISTORICAL
J1939/82_200808
The purpose of these compliance procedures is to generate one or more test documents that outline the tests needed to assure that an ECU that is designed to operate as a node on a SAE J1939 network would do so correctly. SAE does not certify devices and these tests and their results do not constitute endorsement by SAE of any particular device. These tests are presented to allow testing of a Device to determine self-compliance by the manufacturer of a device. The manufacturer can use its record of what procedures were run successfully to show the level of compliance with SAE J1939.
Standard

Compliance

2015-06-04
CURRENT
J1939/82_201506
SAE J1939-82 Compliance describes the compliance tests and procedures to verify an SAE J1939 ECU will operate correctly on a SAE J1939 network. The purpose of these compliance procedures is to generate one or more test documents that outline the tests needed to assure that an ECU that is designed to operate as a node on a SAE J1939 network would do so correctly. SAE does not certify devices and these tests and their results do not constitute endorsement by SAE of any particular device. These tests are presented to allow testing of a device to determine self-compliance by the manufacturer of a device. The manufacturer can use its record of what procedures were run successfully to show the level of compliance with SAE J1939.
Standard

Compliance

2018-10-20
WIP
J1939/82
SAE J1939-82 Compliance describes the compliance tests and procedures to verify an SAE J1939 ECU will operate correctly on a SAE J1939 network. The purpose of these compliance procedures is to generate one or more test documents that outline the tests needed to assure that an ECU that is designed to operate as a node on a SAE J1939 network would do so correctly. SAE does not certify devices and these tests and their results do not constitute endorsement by SAE of any particular device. These tests are presented to allow testing of a device to determine self-compliance by the manufacturer of a device. The manufacturer can use its record of what procedures were run successfully to show the level of compliance with SAE J1939.
Standard

Application - Configurable Messaging

2015-09-22
CURRENT
J1939/74_201509
The SAE J1939 documents are intended for light, medium, and heavy-duty vehicles used on or off road as well as appropriate stationary applications which use vehicle derived components (e.g. generator sets). Vehicles of interest include, but are not limited to, on- and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements. The purpose of these documents is to provide an open interconnect system for electronic systems. It is the intention of these documents to allow Electronic Control Units to communicate with each other by providing a standard architecture. This particular document, SAE J1939-74, describes the message structure for a set of messages which enable the user to determine and announce to others on the network, the parameter placement within a particular message from the special set of messages defined within this document.
Standard

Application—Configurable Messaging

2010-11-05
HISTORICAL
J1939/74_201011
The SAE J1939 documents are intended for light, medium, and heavy-duty vehicles used on or off road as well as appropriate stationary applications which use vehicle derived components (e.g. generator sets). Vehicles of interest include, but are not limited to, on- and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements. The purpose of these documents is to provide an open interconnect system for electronic systems. It is the intention of these documents to allow Electronic Control Units to communicate with each other by providing a standard architecture. This particular document, SAE J1939-74, describes the message structure for a set of messages which enable the user to determine and announce to others on the network, the parameter placement within a particular message from the special set of messages defined within this document.
Standard

Application - Configurable Messaging

2006-11-21
HISTORICAL
J1939/74_200611
The SAE J1939 documents are intended for light, medium, and heavy-duty vehicles used on or off road as well as appropriate stationary applications which use vehicle derived components (e.g. generator sets). Vehicles of interest include, but are not limited to, on- and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements. The purpose of these documents is to provide an open interconnect system for electronic systems. It is the intention of these documents to allow Electronic Control Units to communicate with each other by providing a standard architecture. This particular document, SAE J1939-74, describes the message structure for a set of messages which enable the user to determine and announce to others on the network, the parameter placement within a particular message from the special set of messages defined within this document.
Standard

Marine Stern Drive and Inboard Spark-Ignition Engine On-Board Diagnostics Implementation Guide

2012-04-13
HISTORICAL
J1939/5_201204
This document describes the application of the SAE J1939 recommended practices for compliance with on-board diagnostic malfunction detection system requirements for marine sterndrive and inboard spark ignition engines, as mandated by the California Air Resources Board (CARB). These Otto-cycle engines are not derived from automotive diesel-cycle engines.
Standard

On Board Diagnostics Implementation Guide

2008-12-08
HISTORICAL
J1939/3_200812
SAE J1939-03 provides requirements and guidelines for the implementation of On Board Diagnostics (OBD) on heavy-duty vehicles (HDV) using the SAE J1939 family of standards. The guidelines identify where the necessary information to meet OBD regulations may be found among the SAE J1939 document set. Key requirements are identified here to insure the interoperability of OBD scan tools across individual OBD compliant vehicles. Market-defined regulations permit the use of SAE J1939 to meet OBD requirements. Implementers are cautioned to obtain and review the specific regulations for the markets where their products are sold. This document is focused on guidelines and requirements to satisfy the State of California Air Resources Board (ARB), the authors of 13 CCR 1971.1, United States Environmental Protection Agency, Euro IV and V requirements from European Commission directives, and UN/ECE WP 29 GRPE WWH OBD Global Technical Regulation (GTR)
Standard

On Board Diagnostics Implementation Guide

2015-11-05
CURRENT
J1939/3_201511
SAE J1939-03 provides requirements and guidelines for the implementation of On Board Diagnostics (OBD) on heavy-duty vehicles (HDV) using the SAE J1939 family of standards. The guidelines identify where the necessary information to meet OBD regulations may be found among the SAE J1939 document set. Key requirements are identified here to insure the interoperability of OBD scan tools across individual OBD compliant vehicles. Market-defined regulations permit the use of SAE J1939 to meet OBD requirements. Implementers are cautioned to obtain and review the specific regulations for the markets where their products are sold. This document is focused on guidelines and requirements to satisfy the State of California Air Resources Board (ARB), the authors of 13 CCR 1971.1, United States Environmental Protection Agency, Euro IV and V requirements from European Commission directives, and UN/ECE WP 29 GRPE WWH OBD Global Technical Regulation (GTR).
Standard

Marine Stern Drive and Inboard Spark-Ignition Engine On-Board Diagnostics Implementation Guide

2008-02-21
HISTORICAL
J1939/5_200802
This document describes the application of the SAE J1939 recommended practices for compliance with on-board diagnostic malfunction detection system requirements for marine sterndrive and inboard spark ignition engines, as mandated by the California Air Resources Board (CARB). These Otto-cycle engines are not derived from automotive diesel-cycle engines.
Standard

Marine Stern Drive and Inboard Spark-Ignition Engine On-Board Diagnostics Implementation Guide

2017-10-13
CURRENT
J1939/5_201710
This document describes the application of the SAE J1939 recommended practices for compliance with on-board diagnostic malfunction detection system requirements for marine sterndrive and inboard spark ignition engines, as mandated by the California Air Resources Board (CARB). These Otto-cycle engines are not derived from automotive diesel-cycle engines.
Standard

On-Highway Equipment Control and Communication Network

2012-11-27
HISTORICAL
J1939/1_201211
SAE J1939-1 On-Highway Equipment Control and Communication Network specifies the minimum set of SAE J1939 documents that define the Truck and Bus Control and Communications Vehicle Network as it applies to on-highway equipment. Vehicles covered include all on-highway straight trucks and road trains. A road train consists of one towing vehicle (tractor) and one or more towed vehicles (trailers and dollies). Dolly axles within the road train are considered to be towed vehicles.
Standard

On-Highway Equipment Control and Communication Network

2018-06-12
CURRENT
J1939/1_201806
SAE J1939-1 On-Highway Equipment Control and Communication Network specifies the minimum set of SAE J1939 documents that define the Truck and Bus Control and Communications Vehicle Network as it applies to on-highway equipment. Vehicles covered include all on-highway straight trucks and combination vehicles. A combination vehicle consists of one towing vehicle (tractor) and one or more towed vehicles (trailers and dollies). Dolly axles within the road train are considered to be towed vehicles.
Standard

Agricultural and Forestry Off-Road Machinery Control and Communication Network

2013-03-11
HISTORICAL
J1939/2_201303
SAE J1939-02 Agricultural and Forestry Off-Road Machinery Network specifies the requirements for application of SAE J1939 in agricultural and forestry equipment. This document specifies the series of documents within the set of SAE J1939 documents that are applicable to agricultural and forestry equipment and provides further requirements for this industry. The SAE and ISO groups have cooperated to define agricultural and forestry networks in a manner to allow compatibility of ECUs and messaging protocols between the A&F and the T&B networks.
Standard

Agricultural and Forestry Off-Road Machinery Control and Communication Network

2019-01-14
CURRENT
J1939/2_201901
SAE J1939-2 specifies the requirements for application of SAE J1939 in agricultural and forestry equipment. This document specifies the series of documents within the set of SAE J1939 documents that are applicable to agricultural and forestry equipment and provides further requirements for this industry. The SAE and ISO groups have cooperated to define agricultural and forestry networks in a manner to allow compatibility of ECUs and messaging protocols between the A&F and the T&B networks.
Standard

OBD Communications Compliance Test Cases for Heavy Duty Components and Vehicles

2017-10-18
CURRENT
J1939/84_201710
The purpose of this Recommended Practice is to verify that vehicles and/or components are capable of communicating a required set of information, in accordance with the diagnostic messages specified in SAE J1939-73, to fulfill the off-board diagnostic tool interface requirements contained in the government regulations cited below. This document describes the tests, methods, and results for verifying diagnostic communications from an off board diagnostic tool (i.e., scan tool) to a vehicle and/or component. SAE members have generated this document to serve as a guide for testing vehicles for compliance with ARB and other requirements for emissions-related on-board diagnostic (OBD) functions for heavy duty engines used in medium and heavy duty vehicles. The development of HD OBD regulations by US EPA and California’s Air Resources Board (ARB) require that diagnostic message services are exercised to evaluate diagnostic communication standardization requirements on production vehicles.
Standard

OBD Communications Compliance Test Cases for Heavy Duty Components and Vehicles

2015-02-18
HISTORICAL
J1939/84_201502
The purpose of this Recommended Practice is to verify that vehicles and/or components are capable of communicating a required set of information, in accordance with the diagnostic messages specified in SAE J1939-73, to fulfill the off-board diagnostic tool interface requirements contained in the government regulations cited below. This document describes the tests, methods, and results for verifying diagnostic communications from an off board diagnostic tool (i.e., scan tool) to a vehicle and/or component. SAE members have generated this document to serve as a guide for testing vehicles for compliance with ARB and other requirements for emissions-related on-board diagnostic (OBD) functions for heavy duty engines used in medium and heavy duty vehicles. The development of HD OBD regulations by US EPA and California’s Air Resources Board (ARB) require that diagnostic message services are exercised to evaluate diagnostic communication standardization requirements on production vehicles.
Standard

OBD Communications Compliance Test Cases for Heavy Duty Components and Vehicles

2016-01-14
HISTORICAL
J1939/84_201601
The purpose of this Recommended Practice is to verify that vehicles and/or components are capable of communicating a required set of information, in accordance with the diagnostic messages specified in SAE J1939-73, to fulfill the off-board diagnostic tool interface requirements contained in the government regulations cited below. This document describes the tests, methods, and results for verifying diagnostic communications from an off board diagnostic tool (i.e., scan tool) to a vehicle and/or component. SAE members have generated this document to serve as a guide for testing vehicles for compliance with ARB and other requirements for emissions-related on-board diagnostic (OBD) functions for heavy duty engines used in medium and heavy duty vehicles. The development of HD OBD regulations by US EPA and California’s Air Resources Board (ARB) require that diagnostic message services are exercised to evaluate diagnostic communication standardization requirements on production vehicles.
X