Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Rapid Prototyping and Implementation of traction motor drive for E- Mobility

2019-11-21
2019-28-2472
Objective / Question: Is it possible to extend the envelope of simulation driven design and its advantages to development of complex dynamic systems viz. traction motor drives? The objective that then follows is how to enable OEM/Tier-1s to reduce wastes in the process of traction motor controller design, development, optimization and implementation. Motor control design to validation process is time consuming and tricky! Additionally, the requirement of software knowledge to write code to implement drive engineer's control ideas. The challenges here are - to name a few - algorithm for real time, addressing memory constraints, debugging, comprehending mathematical overflows, portability & BOM cost. These introduces wastes in parameters like time, cost, performance, efficiency and reliability. Methodology: Developing a new traction motor controller for E Mobility takes 18 - 24 months typically. 2 distinct activities take place in a loop.
Technical Paper

Performance & efficiency Improvement of Electric Vehicle Power train

2019-11-21
2019-28-2483
Introduction: The advent of electric mobility is changing the conventional mobility techniques and their application in automobiles across all segments. This development comes with challenges ranging across varied sub -systems in a vehicle including Power Train, HVAC, Accessories, etc. Objective: This paper would concentrate on the Power train related sub systems & improvement of the same both in terms of Efficiency & Performance. Methodology: The electric power train consists of three major sub parts: 1. Motor Unit 2. Controller with Power electronics 3. Battery Pack with BMS We would concentrate on improving the overall efficiency and performance of all these subsystems while they perform in vehicle environment and work in tandem by deploying following techniques: a. Improved Regenerative Braking for converting vehicles Kinetic energy into electrical energy using specific algorithms and control techniques b.
Technical Paper

ELECTRIC BICYCLE WITH REGENERATIVE BRAKING SYSTEM

2019-11-21
2019-28-2490
One of the significant challenges in the present scenario is the depletion of fossil fuels. As the use of conventional fuel is increasing day by day, it will lead to the complete depletion of fossil fuel in the future. So, an alternate solution to this problem is the use of electric vehicles which is independent of the dependence on fossil fuels. Electric vehicles (EVs) use batteries to power them and are electric motor driven. One advantage of using these electric vehicles is that they are pollution free and smokeless. One of the critical limitations of these electric vehicles is the low driving range per charge. The main proposal of this paper is the implementation of a regenerative braking system (RBS) which helps in recovering the kinetic energy that gets wasted during braking. RBS will be very useful in hilly terrain areas where much potential energy can get recovered while moving down the hill.
Technical Paper

An Energy Harvesting E-SHOCK for Future Mobility

2019-11-21
2019-28-2506
India has emerged as the world’s biggest market for Two-wheelers and Four-wheeler. Besides rising incomes and growing infrastructure in all areas, one big reason for the spurt in sales has been ease of zipping in and out of chaotic city traffic along with road irregularities and potholes. Furthermore, the efficiency increase in the Shock absorber within the vehicle have high demands to use of regenerative solutions, in which e-system can be employed as to recover part of the energy otherwise dissipated in form of heat. The Smart e-Shock can charge battery and illuminate accessories of vehicle. Also, the e-shock can provide the various damping characteristics by changing the Electric load on to it to make system as Semi-Active Suspension. This Smart e-Shock system is based on unique and patented concept of constraining the reciprocating motion of the shock absorber in to a single sense of rotation of e-system and the energy is recuperated and given to the battery from the e-system.
Technical Paper

Antirodent Corrugated tube Development for Fuel tube Rat bite

2019-11-21
2019-28-2536
Rat damages in automobiles/food crops/house hold things are extensive in India. Cases of Rat damages to Car Fuel tubes (plastic) and subsequent fuel leak problems are increasing in India.To protect the Fuel tube from rat bite , a more robust and easy assemble protection method is discussed. Hence Antirodent corrugated tubes are considered to protect fuel tube from rat bite. Antirodent masterbatch (3% ) were added to the corrugated tubes and lab test were done in CAZRI. Antirodent corrugated tubes tested with 2 different species showed better results compared to standard corrugated tubes
Technical Paper

Mechanical Property Evaluation of Paper Honeycomb reinforced Plastics

2019-11-21
2019-28-2538
Mechanical Property Evaluation of Paper Honeycomb Reinforced Plastics Vignesh Balaji S G, Pradeep Hyundai Motor India Engineering Pvt. Ltd, Chennai. India Key Words: Paper Honeycomb, Epoxy Composites, Mechanical Properties, Tensile, Impact & Flexural Test Research and/or Engineering Questions/Objective : Composite Materials are widely being used in many engineering applications because of their desirable properties & Cost, Weight Effectiveness. They are widely being used as their Strength-Weight Ratio is Higher than any Other Material. Paper Honeycomb Material is basically a paper made of honeycomb shapes enforced between layers of Glass Mat. This paper deals with the evaluation of Tensile Strength, Flexural (Three-Point Bending) Strength & Flexural Modulus, Impact Strength of Paper Honeycomb Reinforced Epoxy Composites. The Scope of this Material defines the quality of Paper Honeycomb Reinforced Composites which can be used for Automotive Trim Parts.
Technical Paper

Design optimization for Engine mount

2019-11-21
2019-28-2540
The mounting of an engine plays important role in controlling the vibration transmissibility, alignment of transmission unit within specific limit. Design of any mounting system mainly depends on stiffness, allowed deformation and transmissibility of force, natural frequency and size w.r.t space constraints etc. This paper helps to study the behavior of engine mount with different layer of rubber with defer stiffness. Firstly the design of front engine mount with single rubber layer according to space constraint in vehicle and then analysis is done to determine the deformation and various results using CAE technique. As per the results, design is modified with varying layer of rubber pad and again analysis is done with same boundary condition followed by improved results.
Technical Paper

Design & analysis of 2 point aluminum upper control arm in modular multi link rear suspension system

2019-11-21
2019-28-2564
In current automobile market, due to the need of meeting future CO2 limits and emission standards, demand for hybrid systems is on the rise. In general, the requirements of modern automobile architecture demands modular chassis structure to develop vehicle variants using minimum platforms. The multi-link modular suspension system provides ideal solution to achieve these targets. To match ideal stiffness characteristics of system with minimum weight, aluminum links are proving a good alternative to conventional steel forged or stamped linkages. Design of current 2-point link (Upper Control Arm) is based on elasto-kinematic model developed using standard load cases from multi body dynamics. CAD system used is CATIA V5 to design upper control arm for rear suspension. This arm connects steering knuckle & rear sub frame. For Finite Element Analysis we used Hyperworks CAE tool to analyze design under all load cased & further optimization is done to resolve highly stressed zones.
Technical Paper

NEXT GENERATION POWER DISTRIBUTION UNIT IN WIRING HARNESS

2019-11-21
2019-28-2571
Keywords – Miniaturization, Low Profile (LP) Relays, Low Profile (LP) Fuses, Fuse box, Wiring Harness Research and/or Engineering Questions/Objective With the exponential advancement in technological features of automobile’s EE architecture, designing of power distribution unit becomes complex and challenging. Due to the increase in the number of features, the overall weight of power distribution unit increases and thereby affecting the overall system cost and fuel economy. The scope of this document is to scale down the weight and space of the power distribution unit without compromising with the current performance. Methodology Miniaturization involves replacing the mini fuses and J-case fuses with LP mini and LP J-case fuses respectively. The transition doesn’t involve any tooling modification and hence saves the tooling cost.
Technical Paper

FABRICATION AND WEAR CHARACTERISTICS BASALT FIBER REINFORCED POLYPROPYLENE MATRIX COMPOSITES

2019-11-21
2019-28-2570
Generally brake pads are manufacturing by use of asbestos materials, these materials are chemically harmful and toxic, affects human health. The present investigation fabricates polypropylene composites with mixing constant volume [5 Vol.%] of alumina nano particles and different volume percentages [0%, 5%, 10% & 15%] of basalt fibre by hand layup compression technique. The wear characteristics of polypropylene matrix composites were tested by dry sliding condition using pin on disc apparatus configuration with hardened steel counter-face at elevated temperature. The load was applied 30N to 70N with the interval of 20N and varying of sliding speed 300 rpm to 900rpm with the interval of 300rpm for the time period of 0-180 sec. The wear rate was decreases with addition of alumina nano particle and also increases the frictional force for the effect of basalt fibre content present in the composites. The co-efficient of friction was increases from 0.1 to 0.66 under normal loading condition.
Technical Paper

Impact of wheel-housing on aerodynamic drag and effect on energy consumption on an electric bus body

2019-11-21
2019-28-2394
Role of Wheel and underbody Aerodynamics of vehicle in the formation of drag forces is detrimental to the fuel (energy) consumption during the course of operation at high velocities. This paper deals with the CFD simulation of the flow around the wheels of a bus with different wheel housing arrangements. Based on benchmarking, a model of a bus is selected and analysis is performed. The aerodynamic drag coefficient is obtained and turbulence around wheels is observed using ANSYS Fluent CFD simulation for different combinations of wheel-housing- at the front wheels, at the rear wheels and both in the front and rear wheels. The drag force is recorded and corresponding influence on energy consumption of a Bus is evaluated mathematically. A comparison is drawn between energy consumption of bus body without wheel housing and bus body with wheel housing. The result shows a significant reduction in drag coefficient and fuel consumption.
Technical Paper

Combi Brake System (CBS) design and tuning on an electric two wheeler for cornering maneuver

2019-11-21
2019-28-2399
To reduce the number of traffic accidents, most of the governments have mandated to include Combi Brake System (CBS) or Anti-lock Braking System (ABS) in two wheelers. While most of the homologation requirements for CBS can be fulfilled by straight line motion, CBS behavior is crucial while cornering for safety aspects. When vehicle is in cornering motion, the lateral forces generated at the tire decreases the effective longitudinal force available, which implies lesser braking force at tire. This paper represents a design methodology for tuning CBS for various critical scenarios mainly during cornering maneuver. A detailed study has been made at various combination of vehicle lean angle, vehicle speed and friction coefficient of road in straight line and cornering maneuver to effectively decide on front to rear brake force distribution to avoid either of the tires’ lock-up.
Technical Paper

Development of low cost life saving system for Automotive vehicles during Road Accidents.

2019-11-21
2019-28-2460
According to research study 45% of death cause due to not getting help on time to the injured person. Research has proven that if injured person is not found any option of help then they also loose the power to fight such critical situation due to psychological effect. When vehicle met accident, people are not getting on time support, this delay is the major cause of death in developing nations. Presently there is no any robust system available in market for passenger & commercial vehicles which helps to provide on time help to the injured persons & saves human life. In current situation low cost life saving device is need of our society. This paper deals with the design & development of the low cost-life saving device. This paper also comprises the scenario when any vehicle meet an accidents within certain speed limit then how the intelligent life saving device will work & save the life's.
Technical Paper

Design and Development of Industrial Automotive Battery Management system

2019-11-21
2019-28-2498
Battery operated vehicle need accurate management system because of its quick changes in State of charge (SOC) due to aggressive acceleration profiles and regenerative braking. Li-ion battery needs control over its operating area for its safe working. So, the main objective of the proposed system is to develop a BMS having algorithms to estimate accurate SOC, predict degradation parameters, balance individual cells, manage cell temperature, and provide safe area of operation defined by voltage and temperature. Proposed methodology uses Model-based Design approach wherein nonlinear behavior of battery is modeled as Equivalent Circuit Model to compute the SOC and degradation effect on battery to decide the end of life of battery, also performing inductive Active balancing on cells to equalize the charge. proposed algorithms communicate with the vehicle ECU through CAN to assist the driver for runtime estimation, time for battery swapping, Alerts.
Technical Paper

High Durable PU Metallic Monocoat system for tractor sheet metal application.

2019-11-21
2019-28-2541
In sheet metal painting for various applications like Tractor, Automobile, most attractive coating is metallic paints and it is widely applied using 3 coats 2 bake or 3 coat 1 bake technology. Both options, results in high energy consumption, higher production throughput time & lower productivity in manufacturing process. During various brainstorming & sustainable initiatives, paint application process was identified for alternative thinking to reduce burden on environment & save energy. Various other industry benchmarking & field performance requirement studies helped us identify the critical to quality parameters. We worked jointly with supplier to develop mono-coat system without compromising the performance & aesthetical properties. This results in achieving better productivity, elimination of two paint layers, substantial reduction in volatile organic content, elimination of one baking cycle and energy saving.
Technical Paper

A new appraisal of the thermomechanical behaviour of a hybrid composite brake disc in a formula vehicle

2019-11-21
2019-28-2572
A new appraisal of the thermomechanical behaviour of a hybrid composite brake disc in a formula vehicle Research Objective This paper presents a hybrid composite brake disc with reduced Un Sprung Weight clearing thermal and structural analysis in a formula vehicle.Main purpose of this study is to analyse thermomechanical behaviour of composite brake disc for a formula vehicle under severe braking conditions. Methodology In the disk brake system, the disc is a major part of a device used for slowing or stopping the rotation of a wheel. Repetitive braking of the vehicle leads to heat generation during each braking condition. Based on the practical understanding the brake disc was remodelled with unique slotting patterns and grooves, using the selected aluminium alloy of (AA8081) with reinforcement particle of Silicon carbide (SiC) and Graphite (Gr) as a hybrid composite material for this proposed work.
Technical Paper

Characterization and Durability of Mold-In-Color Engineering Plastics

2019-11-21
2019-28-2542
Plastics are prone to photo oxidative and thermal oxidative degradation under usage conditions due to their chemical nature. From sustainability and cost standpoint, there is an increasing focus on Mold-In-Color (MIC) plastic materials. Simultaneously customer’s expectations on the perceived quality of these MIC parts has been increasing with attractive color and glossy appearance. A study was conducted to analyze the product quality and durability aspects over a prolonged exposure to accelerated weathering condition. Material selected for this study were injection molded specimens of ABS and PC/ABS used in automotive passenger vehicles.
Technical Paper

Effect of Tyre inflation Pressure on Rolling Resistance of Tyre

2019-11-21
2019-28-2415
Rolling resistance, is nothing but the rolling drag, is the force resisting the motion when a body rolls on a surface. It is mainly caused by non-elastic effects; that is,not all the energy needed for deformation of the wheel, roadbed, etc. It is recovered when the pressure is removed, in the form of hysteresis losses and permanent deformation of the tyre surface. So, the rolling resistance contributes to the deformation of roadbed as well as tyre surface of the vehicle. Factors contributing in rolling resistance are tyre inflation pressure, wheel diameter, speed, load on wheel,, surface adhesion, sliding, and relative micro-sliding between the surfaces of contact. In this concerned paper we are significantly working on effect of tyre inflation pressure on rolling resistance and taking all other factors constraint.
Technical Paper

SIMULATION OF SOFTENING AND RUPTURE IN MULTILAYERED FUEL TANK MATERIAL

2019-11-21
2019-28-2557
Research and/or Engineering Questions/Objective Plastic automotive fuel tanks made up of blow molded, multi-layered, high-density polyethylene (HDPE) material can take complex shapes with varying thickness. Accidental drop of fuel tank from a height during handling can lead to development of cracks. Damage can also occur due to an impact during a crash. This can be catastrophic due to flammability of the fuel. The objective of this work is to characterize and develop a failure model for the fuel tank material to simulate damage and enhance predictive capability of CAE for chassis and safety load cases. Methodology Different aspects were considered to develop a characterization and modelling strategy for the HDPE fuel tank. Material properties can be influenced by factors such as, service temperature, rate of deformation, state of stress etc.
X