Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

Engine and Transmission Dipstick Marking

1977-08-01
HISTORICAL
J614_197708
This SAE Recommended Practice provides information useful in the marking of engine and transmission dipsticks used for fluid level indication.
Standard

Class B Data Communication Network Messages-Message Definitions for Three Byte Headers

1995-02-01
HISTORICAL
J2178/4_199502
This SAE Recommended Practice defines the information contained in the header and data fields of non-diagnostic messages for automotive serial communications based on SAE J1850 Class B networks. This document describes and specifies the header fields, data fields, field sizes, scaling, representations, and data positions used within messages.
Standard

Companion Flanges, Type A (External Pilot) and Type S (Internal Pilot)

1991-01-31
HISTORICAL
J1946_199101
This SAE Standard specifies the nominal dimensions and tolerances which affect the interchangeability between companion flanges and mating parts. The flanges covered by this document are designated type A and type S. The type A flanges are equivalent to type A ISO 7646. The type S flanges are equivalent to the type S ISO 7647. Type A is an external (male) pilot construction and type S is an internal (female) pilot construction. These flanges are not interchangeable. Dimensions not specified are left to the discretion of the component manufacturer.
Standard

Marine Stern Drive and Inboard Spark-Ignition Engine On-Board Diagnostics Implementation Guide

2012-04-13
HISTORICAL
J1939/5_201204
This document describes the application of the SAE J1939 recommended practices for compliance with on-board diagnostic malfunction detection system requirements for marine sterndrive and inboard spark ignition engines, as mandated by the California Air Resources Board (CARB). These Otto-cycle engines are not derived from automotive diesel-cycle engines.
Standard

Marine Stern Drive and Inboard Spark-Ignition Engine On-Board Diagnostics Implementation Guide

2008-02-21
HISTORICAL
J1939/5_200802
This document describes the application of the SAE J1939 recommended practices for compliance with on-board diagnostic malfunction detection system requirements for marine sterndrive and inboard spark ignition engines, as mandated by the California Air Resources Board (CARB). These Otto-cycle engines are not derived from automotive diesel-cycle engines.
Standard

Life Cycle Testing of Electric Vehicle Battery Modules

1997-01-01
HISTORICAL
J2288_199701
This SAE Recommended Practice defines a standardized test method to determine the expected service life, in cycles, of electric vehicle battery modules. It is based on a set of nominal or baseline operating conditions in order to characterize the expected degradation in electrical performance as a function of life and to identify relevant failure mechanisms where possible. Accelerated aging is not included in the scope of this procedure, although the time compression resulting from continuous testing may unintentionally accelerate battery degradation unless test conditions are carefully controlled. The process used to define a test matrix of accelerated aging conditions based on failure mechanisms, and to establish statistical confidence levels for the results, is considered beyond the scope of this document. Because the intent is to use standard testing conditions whenever possible, results from the evaluation of different technologies should be comparable.
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses--Part 2: Tests and General Performance Requirements

2005-02-02
HISTORICAL
J2223/2_200502
This SAE Standard defines tests methods and general performance requirements of single-pole and multiple connectors for on-board electrical wiring harnesses of road vehicles. These requirements are not intended for connections internal to electronic devices. This document applies to connectors designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance.
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses - Part 2: Tests and General Performance Requirements

1998-12-01
HISTORICAL
J2223/2_199812
This SAE Standard defines tests methods and general performance requirements of single-pole and multiple connectors for on-board electrical wiring harnesses of road vehicles. These requirements are not intended for connections internal to electronic devices. This document applies to connectors designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance.
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses - Part 2: Tests and General Performance Requirements

2018-10-22
WIP
J2223/2
Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and components that constitute the electrical connection systems in low voltage (0 - 20 VDC) road vehicle applications. These procedures are only applicable to terminals used for In-Line, Header, and Device Connector systems with and without Shorting Bars. They are not applicable to Edge Board connector systems, greater than 20 VAC or DC, or to eyelet type terminals.
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses—Part 2: Tests and General Performance Requirements

2011-02-18
CURRENT
J2223/2_201102
Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and components that constitute the electrical connection systems in low voltage (0 - 20 VDC) road vehicle applications. These procedures are only applicable to terminals used for In-Line, Header, and Device Connector systems with and without Shorting Bars. They are not applicable to Edge Board connector systems, > 20 VAC or DC, or to eyelet type terminals.
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses Part 2: Tests and General Performance Requirements

2003-10-28
HISTORICAL
J2223/2_200310
This SAE Standard defines tests methods and general performance requirements of single-pole and multiple connectors for on-board electrical wiring harnesses of road vehicles. These requirements are not intended for connections internal to electronic devices. This document applies to connectors designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance.
Standard

Connections for On-Board Road Vehicle Electrical Wiring Harnesses--Part 2: Tests and General Performance Requirements

1994-02-01
HISTORICAL
J2223/2_199402
This SAE Draft Technical Report defines tests methods and general performance requirements of single-pole and multiple connectors for on-board electrical wiring harnesses of road vehicles. These requirements are not intended for connections internal to electronic devices. This document applies to connectors designed to be disconnected after mounting in the vehicle in the case of repair and/or maintenance.
Standard

Daytime Running Light

2017-08-17
CURRENT
J2087_201708
This SAE Standard provides test procedures, requirements, and guidelines for a daytime running light (DRL) function.
Standard

Daytime Running Light

2016-06-03
HISTORICAL
J2087_201606
This SAE Standard provides test procedures, requirements, and guidelines for a daytime running light (DRL) function.
Standard

Daytime Running Light

2015-09-02
HISTORICAL
J2087_201509
This SAE Standard provides test procedures, requirements, and guidelines for a daytime running light (DRL) function.
X