Refine Your Search

Topic

Author

Affiliation

Search Results

Standard

Performance Levels and Methods of Measurement of Electromagnetic Radiation from Vehicles and Devices (30 to 1000 MHz)

1981-06-01
HISTORICAL
J551_198106
This SAE Standard covers the measurement of broadband electromagnetic radiation over the frequency range of 30 to 1000 MHz from a vehicle or other device powered by an internal combustion engine or electric motor. Operation of all engines (main and auxiliary) of a vehicle or device is included. All equipment normally operating when the engine is running is also included except operator-controlled equipment, which is excluded. The recommended level applies only to complete vehicles or devices in their final manufactured form. Vehicle mounted rectifiers used for battery charging in electric vehicles are included in this document when operated in their charging mode.
Standard

Performance Levels and Methods of Measurement of Electromagnetic Radiation from Vehicles and Devices (30 to 1000 MHz)

1983-12-01
HISTORICAL
J551_198312
This SAE Standard covers the measurement of broadband electromagnetic radiation over the frequency range of 30 to 1000 MHz from a vehicle or other device powered by an internal combustion engine or electric motor. Operation of all engines (main and auxiliary) of a vehicle or device is included. All equipment normally operating when the engine is running is also included except operator-controlled equipment, which is excluded. The recommended level applies only to complete vehicles or devices in their final manufactured form. Vehicle mounted rectifiers used for battery charging in electric vehicles are included in this document when operated in their charging mode.
Standard

Performance Levels and Methods of Measurement of Electromagnetic Radiation from Vehicles and Devices (30 to 1000 MHz)

1995-07-01
CURRENT
J551_199507
This SAE Standard covers the measurement of broadband electromagnetic radiation over the frequency range of 30 to 1000 MHz from a vehicle or other device powered by an internal combustion engine or electric motor. Operation of all engines (main and auxiliary) of a vehicle or device is included. All equipment normally operating when the engine is running is also included except operator-controlled equipment, which is excluded. The recommended level applies only to complete vehicles or devices in their final manufactured form. Vehicle mounted rectifiers used for battery charging in electric vehicles are included in this document when operated in their charging mode.
Standard

Performance Levels and Methods of Measurement of Electromagnetic Radiation from Vehicles and Devices (30 to 1000 MHz)

1985-10-01
HISTORICAL
J551_198510
This SAE Standard covers the measurement of broadband electromagnetic radiation over the frequency range of 30 to 1000 MHz from a vehicle or other device powered by an internal combustion engine or electric motor. Operation of all engines (main and auxiliary) of a vehicle or device is included. All equipment normally operating when the engine is running is also included except operator-controlled equipment, which is excluded. The recommended level applies only to complete vehicles or devices in their final manufactured form. Vehicle mounted rectifiers used for battery charging in electric vehicles are included in this document when operated in their charging mode.
Standard

Performance Levels and Methods of Measurement of Electromagnetic Radiation From Vehicles and Devices (30 to 1000 Mhz)

1990-03-15
HISTORICAL
J551_199003
This SAE Standard covers the measurement of broadband electromagnetic radiation over the frequency range of 30 to 1000 MHz from a vehicle or other device powered by an internal combustion engine or electric motor. Operation of all engines (main and auxiliary) of a vehicle or device is included. All equipment normally operating when the engine is running is also included except operator-controlled equipment, which is excluded. The recommended level applies only to complete vehicles or devices in their final manufactured form. Vehicle mounted rectifiers used for battery charging in electric vehicles are included in this document when operated in their charging mode.
Standard

Emergency Warning Device and Emergency Warning Device Protective Container

1967-03-01
HISTORICAL
J774B_196703
This SAE Standard provides test procedures and performance requirements for emergency warning devices (triangular shape), without self-contained energy sources, that are designed to be carried in motor vehicles and used to warn approaching traffic of the presence of a stopped vehicle, except for devices designed to be permanently affixed to the vehicle, and provides test procedures and performance requirements for protective containers for such emergency warning devices.
Standard

Emergency Warning Device and Emergency Warning Device Protective Container

1989-12-01
HISTORICAL
J774_198912
This SAE Standard provides test procedures and performance requirements for emergency warning devices (triangular shape), without self-contained energy sources, that are designed to be carried in motor vehicles and used to warn approaching traffic of the presence of a stopped vehicle, except for devices designed to be permanently affixed to the vehicle, and provides test procedures and performance requirements for protective containers for such emergency warning devices.
Standard

Thermal Containment Efficiency of Sleeve Materials

2011-02-21
CURRENT
J2495_201102
This SAE Standard measures the percent thermal efficiency of materials in sleeve form used to contain heat or insulate around a hot component. The percent thermal efficiency (%TE) is determined by measuring the power difference expended by the heat source (cartridge heater) with and without the test sleeve at the specified temperature. See SAE J2302 to measure radiant heat flow of sleeves.
Standard

Fastener Part Standard - Tapping Screws and Metallic Drive Screws (Inch Dimensioned)

2013-08-21
CURRENT
J2596_201308
This SAE Part Standard covers selected inch dimensioned tapping screws and metallic drive screws manufactured in accordance with American Society for Mechanical Engineers dimensional standards. This SAE standard covers material most often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This standard permits the fasteners to be identified and ordered by a Part Identification Number (PIN) as defined in this standard.
Standard

Combination Turn Signal Hazard Warning Signal Flashers

1999-07-15
CURRENT
J2068_199907
This SAE Recommended Practice defines the test conditions, procedures, and minimum design requirements for nominal 6, 12, and 24 V flashers used for both turn signal and hazard warning signaling.
Standard

Combination Turn Signal Hazard Warning Signal Flashers

1994-12-01
HISTORICAL
J2068_199412
This SAE Recommended Practice defines the test conditions, procedures, and minimum design requirements for nominal 6, 12, and 24 V flashers used for both turn signal and hazard warning signaling.
Standard

Combination Turn Signal Hazard Warning Signal Flashers

1990-01-01
HISTORICAL
J2068_199001
This SAE Recommended Practice defines the test conditions, procedures, and minimum design requirements for nominal 6, 12, and 24 V flashers used for both turn signal and hazard warning signaling.
Magazine

SAE Off-Highway Engineering 2001-04-01

2001-04-01
Operator station innovations Off-highway engineers work hard to provide comfort, ease of operation, and reliability to users. As an added challenge, they must design for operators who can spend an entire day working hard in their cab. Designing online Major developments in internet-based technologies are profoundly changing the engineering/design process, revolutionizing the way OEMs and suppliers do business, and speeding the industry's time-to-market. FEA simulation of an electrohydraulic system Researchers from the Milwaukee School of Engineering provide an accurate model of a typical magentic actuator Predicting injury in forklift upsets Researchers from the Biomechanics Institute present test results that demonstrate operators can prevent ejection and injury from a forklift if they are lap-belted and have either a winged seat or hip restraint.
Standard

METHODS OF TESTS FOR AUTOMOTIVE-TYPE SEALERS, ADHESIVES, AND DEADENERS

1971-10-01
CURRENT
J243_197110
This SAE Recommended Practice contains a series of test methods for use in measuring characteristics of automotive-type sealers, adhesives, and deadeners. The test methods which are contained in this document are as follows: ADS-1—Methods of Determining Viscosity ADS-2—Low Temperature Tests ADS-3—Weld-Through Tests ADS-4—Enamel, Lacquer, and Fabric Staining Test ADS-5—Wash-Off Resistance Test ADS-7—Solids Test ADS-8—Flash Point Test ADS-9—Sag and Bridging Tests ADS-10—Flow Test The intent of this document is to provide a series of test methods which can be used in testing the various qualities of sealers, adhesives, and deadener material. In later revisions of this document, attempts will be made to reduce the number of tests now presented. The specific temperatures and times at which some of these tests are to be conducted are not dictated in these test procedures, but they will be found in the material standards which govern each type of material to be tested.
Standard

Coupling Assembly, Threadless, Flexible, Fixed Cavity, Self-Bonding, Metric

1993-11-01
CURRENT
MA2241
This document defines the requirements for a threadless, flexible, self-bonding coupling assembly, which, when installed on machined fixed cavity ferrules, provides a flexible connection for joining tubing and components in aircraft fuel, vent, or other systems. This assembled coupling, hereafter referred to as the assembly, is designed for use from -54 to 204 °C and at 862 kPa operating pressure. AS coupling components referenced herein have been qualified to AS1650. Ferrules referenced herein are inch ferrules adapted to metric tubing.
Standard

Bolts and Screws, UNS N07001 Tensile Strength 1210 MPa, Thread and Fillet Radius Rolled Before Aging, Procurement Specification, Metric

1997-06-01
HISTORICAL
MA3378C
This specification covers metric bolts and screws made from a corrosion and heat resistant, nickel-base alloy of the type identified under the Unified Numbering System as UNS N07001. The following specification designations and their properties are covered: MA3378 1210 MPa minimum ultimate tensile strength at room temperature 520 MPa stress-rupture strength at 730 °C MA3378-1 1210 MPa minimum ultimate tensile strength at room temperature 726 MPa minimum ultimate shear strength at room temperature
Standard

Bolts and Screws, UNS N07001 Tensile Strength 1210 MPa, Thread and Fillet Radius Rolled Before Aging, Procurement Specification, Metric

2018-01-19
CURRENT
MA3378D
This specification covers metric bolts and screws made from a corrosion and heat resistant, nickel-base alloy of the type identified under the Unified Numbering System as UNS N07001. The following specification designations and their properties are covered: MA3378 1210 MPa minimum ultimate tensile strength at room temperature 520 MPa stress-rupture strength at 730 °C MA3378-1 1210 MPa minimum ultimate tensile strength at room temperature 726 MPa minimum ultimate shear strength at room temperature
X