Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

“Rigidization-on-Command”™ (ROC) Resin Development for Lightweight Isogrid Booms with MLI

2003-07-07
2003-01-2342
The “Rigidization-on-Command”™ (ROC™) resin development has focused on the development of resin systems that use UV light cure for rigidization. Polymeric sensitizers have been incorporated into the resin formulations to promote cure using Pen-Ray lamps and UV light-emitting diodes (LED's). Formulations containing the polymeric sensitizers were examined by FTIR and DSC. Complete cure was observed after 15 min. exposure with the Pen-Ray lamps. Performance of the Pen-Ray lamps and UV LEDs was thoroughly characterized. Thermal models were developed to optimize the performance of the of the MLI insulation thermal oven used for orbital cure of the boom. Results show that -12°C is the lowest temperature required for cure of the ROC™ resin systems.
Technical Paper

“Rubber Coupling” at a 4×4 Transmition System

2003-11-18
2003-01-3684
There are many different vibration sources in a car. Engine, gears, road roughness, impacts against the wheels cause vibration and sound that can decrease the parts and the car durability as well as affect drivability, safety and passengers and community comfort. In 4×4 cars, some extra vibration sources are the parts responsible for transmitting the torque and power to the rear wheels. Each of them has their own vibration modes, excited mostly by its imbalance or by the second order engine vibration. The engine vibration is a very well known phenomena and the rear driveshaft is designed not to have any vibration mode in the range of frequencies that the engine works or its second order. The imbalance of a driveshaft is also a design requirement. That means, the acceptable imbalance of the driveshaft is limited to a maximum value.
Technical Paper

“SODART” Telescope Silicon Detector Cooling System (Thermal Test Results of the Scale-Down Model)

1992-07-01
921365
The onboard “SODART” telescope silicon detector cooling system of the “Spectrum-X-Gamma” observatory, which is designed for the space objects X-ray radiation study, is described. The scale-down model of the passive cooling system description and thermal vacuum test results of this model are given. In the real cooling system the minimal detector temperature at 300 mW heat release is expected about 107 K.
Technical Paper

“STATE OF THE ART” REPORT ON WINTERIZATION OF CONSTRUCTION EQUIPMENT

1964-01-01
640064
As increasing populations set demands for the abundant natural resources of the colder regions, the complex industrial machines of American Industry are expected to build the new railroads, roads, cities, mines, power sources, airports and factories, and operate these activities year round. This paper reviews the basic problems of “winterization” and the design practices, materials and components used with varying effectiveness in “winterizing” construction and associated equipment for use in moderate and extreme cold geographical areas. Several new charts are included which offer design temperature data for the northern United States, Canada, Alaska, Greenland, as well as average January isotherms around the earth. The authors are members of CIMTC Subcommittee XV, “Environment”.
Technical Paper

“Sky Hooks” for Automobiles

1935-01-01
350109
IN this paper the authors present some experimental results obtained by using the analysis outlined by Prof. James J. Guest before the Institution of Automobile Engineers, in 1926. To make the experimental work more understandable, they present the essential points of Professor Guest's analysis. Professor Guest begins his analysis of the movements of a car body with the simplest set of conditions and presents a graphical as well as an algebraic solution. He then includes one additional factor after another in his analysis until the principal factors in car suspension are included. After all factors are considered, the essential structure of the simple analysis is retained. The authors' efforts at the experimental determination of the moment of inertia of passenger cars were started in January, 1932, on Sir Charles Dennistoun Burney's “tear-drop” design with which he visited leading American manufacturers.
Technical Paper

“Smart Panel” Electronic Circuit Breaker Control Technology

2008-11-11
2008-01-2880
This paper will discuss using Astronics “Smart Panel” illuminated control panels to control an electronic power distribution system. A discussion of wiring simplification, automatic control possibilities and real time load monitoring is presented. The challenges of retrofitting the system into older aircraft will be covered as well. The paper also explains Electronic Circuit Breaker technology, arc fault protection, panel lighting technologies, control bus options, displays, and human input technology (buttons and knobs).
Technical Paper

“Smart sensing” of Oil Degradation and Oil Level Measurements in Gasoline Engines

2000-03-06
2000-01-1366
Proper lubrication of moving parts is a critical factor in internal combustion engine performance and longevity. Determination of ideal lubricant change intervals is a prerequisite to ensuring maximum engine efficiency and useful life. When oil change intervals are pushed too far, increased engine wear and even engine damage can result. On the other hand, premature oil changes are inconvenient, add to vehicle maintenance cost, and result in wasted natural resources. In order to determine the appropriate oil change interval, we have developed an oil condition sensor that measures the electrical properties of engine oil, and correlates these electrical properties to the physical and chemical properties of oil. This paper provides a brief background discussion of the oil degradation process, followed by a description of the sensor operational principles and the correlation of the sensor output with physical and chemical engine oil properties.
Technical Paper

“Standardizing the Datasheet” Towards Auto-Code Generation Efficiency

2009-04-20
2009-01-0270
Software programs in non-application areas such as Board Support Packages, Hardware Abstraction Layers, signal processing and data acquisition are more or less very standard and common across many applications. These form a major part of the “platform” software, which changes very little. However, it is seen that many a time, efforts are spent resolving issues in the hardware dependent layers rather than concentrating on the application at hand, despite the fact that the software controlling the hardware has been developed many times. There are many reasons why this section of the software is rewritten many times over: different coding standards, different software architecture and layering concepts, the dreadful cut-and-paste methods, and so on. Introduction of a tool-based code configurator and generator eliminates access to the code and focuses on configuring a pre-written set of SW procedures. Advantages: Standardization, reuse and high levels of productivity.
Technical Paper

“Symbiose”: Technology Developments for Bioregeneration in Space

1994-06-01
941348
Dedicated technology has been developed to support long-term biological experiments on-board spacecraft. These developments include a microgravity compatible tubular photo bioreactor for the cultivation of micro algae at very high biomass concentrations and with very high gas exchange rates, a microgravity compatible gas / liquid phase separator which also works as a pneumatic low shear-stress pump, a microgravity compatible dehumidifier, and a maltose separating reverse osmosis unit. Integration of these technologies into a partially closed artificial ecosystem form the foundation of the SYMBIOSE concept (System for Microgravity Bioregenerative Support of Experiments).
Technical Paper

“Targeting Consumer Needs in the Perfect Storm: Changing the Automotive Lifestyle”

2008-10-20
2008-21-0038
The intersection of changing lifestyles and evolving transportation needs finds smart USA well positioned for launch in 2008 during one of the most competitive periods in U.S. automotive history. In a zero sum market with new global entrants competing for single points of share, where quality levels have been redefined and fractions of points separate the best from the challengers, lifestyle awareness, innovation and product positioning become the differentiators. Simply adding features has left some with hefty investments and confused consumers. Bigger is not always better. More is not always desirable. The real opportunity for new entrants to the US market may be defined within niche markets where changing lifestyles allow for the emergence of new segments. Today, smart USA has surfaced as a clear example of right product, right place, right time.
Technical Paper

“Telematics Business focused on e-services”

2000-12-01
2000-01-3199
The approach of the proposed technical work: - Brazilian market needs and requirements - The Internet growing up and Telematics, - Potential business to be found out, - Technical approach, - Conclusions
Article

“The Eagle has landed”

2018-10-08
Lockheed Martin has revealed its concept for a new crewed lunar lander: a single stage, fully reusable system that incorporates flight-proven technologies and systems from the NASA Orion spacecraft. In its initial configuration, the lander would deliver a crew of four and 2,000 pounds of cargo to the Moon’s surface for up to two weeks.
Technical Paper

“The Impact Of The Microprocessor On Aircraft Electric System Control Philosophy”

1981-10-01
811085
The use of microprocessors for the implementation of control functions in aircraft electric systems has become a reality. This paper presents a brief survey of these systems along with a typical system block diagram. A description of the diagram highlights the advantages of microprocessor systems over existing noncomputerized control schemes. The second half of the paper discusses the adaptability of more advanced microprocessor systems in the next generation of aircraft electric systems. These powerful new computers will allow digital control and protection of single unit and paralleled generating and starting systems, as well as providing even more effective built-in-test.
Technical Paper

“The Network Vehicle - A Glimpse into the Future of Mobile Multi-Media”

1998-11-09
982901
The Network Vehicle is the Delphi Automotive Systems' vision for the future convergence of the communications infrastructure, computers, and the automobile. It features many advanced functions such as: satellite video, Internet access, virtual navigation, remote vehicle diagnostics and control, games, mobile office, automotive web site, and customized real-time stock quotes and sports scores. These features are enabled by an integrated planar antenna that is capable of multiple satellite reception, a client-server network architecture, and unique human-vehicle-interfaces. The software application is written in Java, using API's (Application Programming Interfaces) to reduce the complexity and cost of the source code.
Journal Article

“Verify-on-Demand” - A Practical and Scalable Approach for Broadcast Authentication in Vehicle-to-Vehicle Communication

2011-04-12
2011-01-0584
In general for Vehicle-to-Vehicle (V2V) communication, message authentication is performed on every received wireless message by conducting verification for a valid signature, and only messages that have been successfully verified are processed further. In V2V safety communication, there are a large number of vehicles and each vehicle transmits safety messages frequently; therefore the number of received messages per second would be large. Thus authentication of each and every received message, for example based on the IEEE 1609.2 standard, is computationally very expensive and can only be carried out with expensive dedicated cryptographic hardware. An interesting observation is that most of these routine safety messages do not result in driver warnings or control actions since we expect that the safety system would be designed to provide warnings or control actions only when the threat of collision is high.
Technical Paper

“Web-ACSYNT”: Conceptual-Level Aircraft Systems Analysis on the Internet

1997-10-01
975509
A Web-based version of the aircraft design program ACSYNT has been created. “Web-ACSYNT” provides the user with a familiar user interface and is accessible from multiple platforms. Analyses are based upon a set of baseline aircraft models which can be modified through a carefully selected set of parameters related to weight, aerodynamics, propulsion, economics, and mission. The software is intended to become one of the models that comprise the Aviation System Analysis Capability (ASAC) currently being developed by NASA under the Advanced Subsonic Technology (AST) program.
X