Search Results

Increasing urbanisation and the growing environmental awareness in society require new and innovative vehicle concepts. In the present work, the design freedoms of additive manufacturing (AM) are used to develop a front axle wheel suspension for a novel modular vehicle concept. The development of the suspension components is based on a new method using industry standard load cases for the strength design of the components. To design the chassis components, first the available installation space is determined and a suitable configuration of the chassis components is defined. Furthermore, numerical methods are used to identify component geometries that are suitable for the force flow. The optimisation setup is selected in a way that allows to integrate information, energy and material-carrying conductors into the suspension arms. The conductors even serve as load-bearing structures because of the matching design of the components.

The requirement for lightweight, high-performance materials with higher wear resistance, which is critical in industries such as aerospace, automotive, and consumer-related sectors, has fueled the development of particle reinforced metal matrix composites (PRMCs). These materials are an appealing alternative for a broad variety of scientific and technological applications due to their remarkable mechanical qualities and low cost. The primary goal of developing metal matrix composite materials is to combine the favorable properties of metals and ceramics. This study included several experimental experiments to explore the behavior of stir-cast composites made of aluminum grade 6063 with varying amounts of SiC, Al2O3, and TiO2 reinforcements.

Laser powder bed fusion is one of the metal additive manufacturing technologies, so-called 3D printing. It has attracted great attentions due to high geometrical flexibility and remarkable metallurgical characteristics. An oil catch tank has been widely used in automotive industries for filtering oil vapors or carbon sludge from blow-by gas as a conventional usage. A pneumatic valve system mainly adopted to high-performance engines is also a potential application of it because undesirable oil infiltrates into air springs during engine operation, resulting in an excess spring pressure. This work focused on developing a lightweight oil catch tank which can be applied to a pneumatic valve system by taking advantage of additive manufacturing techniques. Al-Mg-Sc alloy powder with high tensile strength as well as high ductility were used under the consideration of specific strength, printability and availability.

The rapidly growing amount of software in cars reshapes the automotive industry. The software has a significant influence on the production lines, due to the time required to flash it onto the vehicle and its capabilities to test vehicle functions during production. In this paper we identify the main pain points regarding software in the manufacturing process by performing a structured analysis on the experiences made at a major car manufacturer over last two years. Consequently, the paper analyses the possible approaches to address the challenges.

Over the last decade, Climate change due to fossil fuel burning has taken centre stage in all discussions. Automotive sector has come under some flak for being one of the contributors to this Climate Change. Active steps have been taken by Vehicle Manufacturers and their Suppliers to address this issue. This sector has been facing below challenges to reduce pollutant in the air by A. Reducing Emissions, B. Increasing Energy Efficiency C. Use of Renewable Energy. One of the many alternatives by the Automotive Industry was to have a phased introduction to Electric Vehicles (EV), Hybrids, Fuel cells and other variants. As various emission norms and safety requirements takes Centre stage, it invariably, increases the weight of the vehicle. Now a days, Vehicles are having challenges to make it lightweight to achieve Range for an EV and improve fuel efficiency without sacrificing safety.

Historically manufacturing variability has been considered as a noise factor due to limited insights about manufacturing history and its influence on part performance. With improvement in computational power and enhancements in commercial simulation tools, it is now feasible to study the influence of manufacturing process on product life in addition to manufacturability. This study demonstrates the concept of as manufactured part performance prediction utilizing forming simulation software to capture deformed geometry along with residual stresses and its integration to performance simulation tool using sheet drawing operation. Simulation predictions are verified and validated with available experimental data. This approach helps to visualize the variation in part performance with respect to manufacturing process change including process sequence, process parameters and tooling design change.

The present work focusses on development of AlSi10Mg alloy component from the pre-alloyed powder by laser powder bed fusion (LPBF), one of the popular additive manufacturing technologies. The effect of heat treatment on microstructure and mechanical properties has also been studied. In accordance with T6 heat treatment process, the LPBF specimens were solution treated at 535°C for 2 h, then water quenched and subsequently, artificially aged at 160°C for 10 h. The role of printing direction on microstructure and mechanical properties has also been investigated. The printing parameters such as laser power, scan speed and hatch space were optimized for defect free automotive component. The as-printed and heat treated components were subsequently evaluated to assess their performance.

The usage of forging a preformed, near net shape, compacted and sintered metal powder has been widely accepted since the eighties and is now one of the mainstays for producing Connecting rods in North America. However, its use in Indian subcontinent is limited as its counterpart i.e. conventional steel forging is still the most dominant. Powder metallurgy route has many advantages like good dimensional accuracy; minimum scattering of weight etc. Despite these advantages, the Powder metallurgy process is still not preferred predominantly due to technical (endurance) and infrastructural limitations. This work envisages combining the benefits of powder metallurgy process with the required mechanical properties viz. tensile and fatigue strength alongside design modifications to meet the requirements of a connecting rod for a 2-cylinder diesel engine. The connecting rods met the fatigue life at the required FOS equaling the performance of a conventionally forged connecting rod.

Helmholtz resonator is a very common anechoic measure, and it is widely used in pipe acoustic fields. Based on the enlightenment of the classic Helmholtz resonator, this paper proposes a headrest resonator model and extends it to the acoustic field of the passenger cabin to improve the road noise in the car. Firstly, through the theoretical model of Helmholtz resonator, the relationship between its resonance frequency and the geometric size of the resonator is clarified. Secondly, the influence of the headrest resonator on the acoustic field characteristics of the car is studied through finite element simulation analysis. It is demonstrated that the headrest resonator is placed in the car, and the sound pressure distribution characteristics of the passenger's inner ear near the resonance frequency change significantly. At the same time, through 3D printing, a sample of the headrest resonator is made.

The paper discusses the process of developing an SAE damping measurement test method that is suitable for testing bars that are not made of steel or are difficult to measure with the traditional Oberst bar method. The method is based on measuring mechanical impedance (force over velocity) of a vibrating bar. The bar is excited at the center using a shaker and hence it is also called a CenterPoint method. The paper discusses the round robin tests that have been conducted so far and discusses the test results that will help develop the standard. The paper discusses the variability of the round robin test results within a laboratory, between laboratories, as well as the coefficient of variation for these measurements. The paper also discusses various parameters that should be carefully monitored in this study, that otherwise could affect the precision of the test procedure.

As part of the update process to SAE J1637, “Laboratory Measurement of the Composite Vibration Damping Properties of Materials on a Supporting Steel Bar”, the Acoustical Materials Committee commissioned a round robin study to determine the current laboratory-to-laboratory variation, and to better understand best practices for composite loss factor measurements. Guidance within the current standard from a previous round robin study indicates a coefficient of variation of 35% for laboratory-to-laboratory measurements. It was hoped that current instrumentation and test practices would yield lower variability. Over the course of 5 years, 10 separate laboratories tested 4 bars: three damped steel bars and one bare steel bar. The bars were tested at -20°C, -5°C, 10°C, 25°C, 40°C, and 55°C. The damping materials were intentionally selected to provide low damping, moderate damping, and high damping to illustrate difficulties in determining the composite loss factor with increased damping.

To reduce the noise in the frequency range of 100Hz~1000Hz, a metamaterial structure composed of lightweight frame, hard membrane-like material and added mass is proposed in this paper. The advantage of this structure is that it is lightweight and the membrane-like material does not need to be stressed in advance. Finite element method (FEM) and experiment are used to investigate the sound transmission loss (STL) performance of the metamaterial structure. The results show that the peak STL is caused by the local resonance of the added mass and the membrane-like material. The valley versus frequency results from the resonance frequencies of metamaterial structure, and it is divided into three resonance frequencies: resonance frequencies from added mass, membrane-like material and frame.

A high compression ratio is an effective means for improving the thermal efficiency of an internal combustion engines. However, a high compression ratio leads to a rapid rise in the combustion pressure, as it causes a high impulse force. The impulse force generates vibrations and noise by spreading in the engine. Therefore, reducing the vibration of the combustion (which increases as the compression ratio increases) can improve the thermal efficiency while using the same technology. We are conducting model-based research on technologies for reducing combustion vibration by applying a granular damper to a piston. To efficiently reduce the vibration, we suppress it directly with the piston, i.e., the source of the vibration. Thus, the damping effect is maximized within a minimized countermeasure range.

Automotive industry is looking for high strength and durable lightweight material with resistance to wear and friction. To meet this requirement, a new hybrid polymer composite material has been developed using reinforcement as SS 304 wire mesh and jute fibre. Present paper explores the experimental findings of wear performance of hybrid polymer composite under dry condition. Four different laminates with configurations JJSJJSJJ, (JJSJJSJJ)450, GGSGGSGG and GJSJJSJG along with their virgin counterpart were developed by hand layup technique supported by compression moulding. These laminates were tested as per the ASTM standards to investigate its performance for friction and wear using pin on disc machine with steel as a counterpart. Testing parameters were sliding distance, applied load and sliding speed. Experimental results showed that, applied load have major influence on the friction and wear performance of developed hybrid composites.

Vibration control plays a critical role in conventional as well as next-generation vehicles. Construction of the vehicle, road conditions, and driving patterns are the major sources of the vibrations that cause discomfort to the passengers in the vehicle. Composite material is being looked at as an alternative material in the automotive sector due to its higher specific strength and good damping properties. In this research, the test specimen of steel plate used in automotive has been considered. The damping vibration test has been carried out on the test specimen by using the FFT analyzer to evaluate the natural frequency and damping. Thereafter, the hybrid composite material is developed with the natural fibers as reinforcement with steel plate to reduce the vibrations. The test specimens with different layers of damping materials have been prepared for this research. Jute, hemp, banana, and flax are used for the preparation of different composite materials.

Access control enforces security policies for controlling critical resources. For V2X (Vehicle to Everything) autonomous military vehicle fleets, network middleware systems such as ROS (Robotic Operating System) expose system resources through networked publisher/subscriber and client/server paradigms. Without proper access control, these systems are vulnerable to attacks from compromised network nodes, which may perform data poisoning attacks, flood packets on a network, or attempt to gain lateral control of other resources. Access control for robotic middleware systems has been investigated in both ROS1 and ROS2. Still, these implementations do not have mechanisms for evaluating a policy's consistency and completeness or writing expressive policies for distributed fleets. We explore an RBAC (Role-Based Access Control) mechanism layered onto ROS environments that uses local permission caches with precomputed truth tables for fast policy evaluation.

The application of virtual engineering methods can streamline the product design process through improved collaboration opportunities among the technical staff and facilitate additive manufacturing processes. A product digital twin can be created using the available computer-aided design and analytical mathematical models to numerically explore the current and future system performance based on operating cycles. The strategic decision to implement a digital twin is of interest to companies, whether the required financial and workforce resources will be worthwhile. In this paper, two metrics are introduced to assist management teams in evaluating the technology potential. The usefulness and time savings metrics will be presented with accompanying definitions. A case study highlights the usefulness metric for the “Deep Orange” prototype vehicle, an innovative off-road hybrid vehicle designed and fabricated at Clemson University.

Now for past many decades, automotive manufacturing is under perennial pressure owing to consumer aspirations, regulations, globalized competition and sustainability needs. Automotive manufactures are fiercely satisfying all of above constraints through innovative solutions. The resultant vehicles have many complex to very complex systems and subsystems to deliver the performance aspirations. In this game, one of the critical business parameter is rapid time to market. At the current state of the art, time to market directly conflicts with new product development time. Four wheeler new product development consumes upward of 48 months, while risking obsolescence of product features at the time of launch. Automotive manufacturers invest intensely in technologies to achieve this goal of short time to market. Digital technologies delivering high time efficiency have made deep in roads in the automotive product development arena.

Fretting fatigue was observed in standard cylindrical fatigue samples at the regions in contact with the grips of the test frames during fatigue testing for AlSi10Mg aluminum alloy produced by laser powder bed fusion process (L-PBF). The failure of the fatigue sample grips occurs much earlier than the failure of the gauge section. This results in a damaged sample and the sample cannot be reused to continue the test. This type of failure is rarely seen in materials produced by traditional manufacturing processes. In this study, X-ray residual stress analysis was performed to understand the cause of failure for L-PBF AlSi10Mg with the as-built surface condition. The result indicates that the fretting fatigue failure was caused by the strong tensile residual stress in the as-built state combining with the fretting wear between the sample and the grip. A few potential solutions to avoid the fretting fatigue failure were investigated.

Additive Manufacturing (AM) using stereolithography (SLA) was applied to produce engine O-rings using two different flexible polymer printing materials, Flex 80A and Elastic 50A. Print orientation of the O-ring in the SLA 3D printer is important, with the horizontal configuration most commonly providing for the smoothest final O-ring printed surface due to the lack of printing support tabs required. AM printing tabs lead to O-ring ‘marks’ (non-smooth surfaces) that were evaluated using the Society of Automotive Engineers SAE AS871B standard. It was seen that numerous printing approaches produced ‘marks’ that were larger than acceptable, which shows that these studied AM processes can not replace traditional methods of O-ring manufacture. However, further evaluation was pursued to explore possible remote emergency usage of these O-rings. Printed O-rings were next tested-soaked in engine related fluids in order to characterize O-ring swelling behavior.