Search Results

From 1 September 2014 new car types in the EU must meet ‘Euro 6’ emissions requirements. The ‘New European Driving Cycle’ (NEDC) is currently the main test for this, but the European Commission intends to also introduce PEMS (Portable Emissions Measurement Systems)-based procedures to ensure that emissions are well controlled in real use. ‘Random Cycles’ have also been considered and remain a possible option for ‘real world’ particle number measurement. At the same time, the UN Working Party on Pollution and Energy (GRPE) has developed the new Worldwide harmonized Light vehicles Test Procedure (WLTP) that is expected to be adopted in the EU in the near future. To identify and understand the differences in emissions that may arise between these various methodologies, AECC has conducted some initial tests on two modern light-duty vehicles.

Diesel engine emits soot which causes harm to human health, air quality and climate. It is important to understand the formation and time evolution of soot and its size distribution evolution inside engines to design strategies for emission reduction. We have developed a 0D multi-zone model for diesel fuel spray and coupled it with detailed surrogate diesel fuel chemistry and a sectional aerosol dynamics model for soot nucleation, surface growth and coagulation. Variable equivalence ratios in different zones are created by fixed fuel injection rates and variable air entrainment rates by a normal distribution function in different zones which ensures the existences of different pollutant forming zones having different equivalence ratios. Engine exit measured data of total soot mass and NOx for one operating condition are used to optimize the three model parameters. Model simulation of soot size distribution is consistent with typical measured data.

The objective of this work is to develop a numerical simulation model of spark ignited (SI) engine combustion and thereby to investigate the possibility of reducing heat losses and improving thermal efficiency by applying a low thermal conductivity and specific heat material, so-called heat insulation coating, to the combustion chamber wall surface. A reduction in heat loss is very important for improving SI engine thermal efficiency. However, reducing heat losses tends to increase combustion chamber wall temperatures, resulting in the onset of knock in SI engines. Thus, the numerical model made it possible to investigate the interaction of the heat losses and knock occurrence and to optimize spark ignition timing to achieve higher efficiency. Part 2 of this work deals with the investigations on the effects of heat insulation coatings applied to the combustion chamber wall surfaces on heat losses, knock occurrence and thermal efficiency.

In the present paper, two different methodologies are adopted and critically integrated to analyze the knock behavior of a last generation small size spark ignition (SI) turbocharged VVA engine. Particularly, two full load operating points are selected, exhibiting relevant differences in terms of knock proximity. On one side, a knock investigation is carried out by means of an Auto-Regressive technique (AR model) to process experimental in-cylinder pressure signals. This mathematical procedure is used to estimate the statistical distribution of knocking cycles and provide a validation of the following 1D-3D knock investigations. On the other side, an integrated numerical approach is set up, based on the synergic use of 1D and 3D simulation tools. The 1D engine model is developed within the commercial software GT-Power™. It is used to provide time-varying boundary conditions (BCs) for the 3D code, Star-CD™.

A model for the calculation of heat release in direct injection Diesel engines is presented. It needs only one engine-specific experimental parameter. In the form the model is presented here it is limited to the medium and upper load range, where Diesel combustion is mainly mixing controlled. The development of the model is based on data from medium speed engines. The applicability to automotive engines is shown in some examples. The model is based on the theory of single phase turbulent jets. Starting from the balance of momentum and fuel mass flow the stationary part of the jet can be calculated. The propagation of the front of the unsteady jet is determined from a continuity consideration. Heat release is calculated based on the assumptions of the Simple Chemically Reacting System (SCRS). Fuel that is mixed with air is assumed to be burnt instantaneously.

While many composite monocoque and semi-monocoque chassis have been built there is very little open literature on how to design one. This paper considers a variety of issues related to composite monocoque design of an automotive chassis with particular emphasis on designing a Formula SAE or other race car monocoque chassis. The main deformation modes and loads considered are longitudinal torsion, local bending around mounting points, and vertical bending. The paper first considers the design of elements of an isotropic material monocoque that has satisfactory torsional, hardpoint, and vertical bending stiffness. The isotropic analysis is used to gain insight and acquire knowledge about the behavior of shells and monocoque structures when subjected to a vehicle's applied loads. The isotropic modeling is then used to set initial design targets for a full anisotropic composite analysis.

The first objective of this work is to develop a numerical simulation model of the spark ignited (SI) engine combustion, taking into account knock avoidance and heat transfer between in-cylinder gas and combustion chamber wall. Secondly, the model was utilized to investigate the potential of reducing heat losses by applying a heat insulation coating to the combustion chamber wall, thereby improving engine thermal efficiency. A reduction in heat losses is related to important operating factors of improving SI engine thermal efficiency. However, reducing heat losses tends to accompany increased combustion chamber wall temperatures, resulting in the onset of knock in SI engines. Thus, the numerical model was intended to make it possible to investigate the interaction of the heat losses and knock occurrence. The present paper consists of Part 1 and 2.

Flexible polyurethane (PU) foam has been widely used for seat cushions in automotive passenger vehicles due to the excellent cushioning performance and the ability to shape mold. Originally introduced in the late 1950's, it has been used for more than 50 years. However, there is a limitation using polyurethane foam with efforts to reduce the weight and address ever increasing risks to environment. This paper provides information about a new automotive seat concept which does not use polyurethane foam at all. Expanded polyolefin foam is used for this application to replace polyurethane foam and achieve comparable cushioning performance. Other features of the material include 100% recyclability, and no VOC's. By replacing polyurethane foam with expanded thermoplastic foam, hazardous outgassing is eliminated during the seat cushion production, thus improving workplace environmental health and safety.

Nanobridization is a nano-inspired process by which scalable material structures can be designed and manufactured by combining the concept of ‘Nano Free Volume’ with specific material molecules defining a systemic density (nano-density). This approach explores nanotechnology from a porosity perspective rather than nanoparticles thus minimizing health concerns with nanotechnology, while providing nanoporosity throughout the entirety of the composite system. Nanobridization may be viewed as a density system transformation of material heterogeneity utilizing a unified class of materials such as Polynanomers and in developing next generation structures such as Featherweight Carbon Fiber Reinforced Polymers (CFRP). Polynanomers are further defined by the incorporation of hollow carbon fibers, electrospun nano-fibers, nano-pores and carbon nanotubes (CNT) into this newly established type of matrix.

It is commonly recognized that the paths for improving fuel consumption (BSFC) in a spark-ignition engine at part-load require more advanced valve actuation strategies, which largely affect the pumping work. Since several years, many different solutions have been proposed, characterized by different levels of complexity, effectiveness, and cost. Valve systems currently available on the market allow for variable phasing (VVT - Variable Valve Timing), and/or lift (VVA - Variable Valve Actuation). Usually VVT devices are applied on intake and exhaust camshafts, in the “phased” or “unphased” configuration, as well. VVA devices are instead commonly mounted on the intake camshaft. More recent VVA systems also allow for a double intake valve lift during a single engine cycle (multi-lift), or may include a small intake pre-lift during the exhaust stroke. The latter solutions may determine further BSFC reductions. Alternatively, an external-EGR circuit can be considered, as well.

This works presents a real-time capable simulation model for dual fuel operated engines. The computational performance is reached by an optimized filling and emptying modeling approach applying tailored models for in-cylinder combustion and species transport in the gas path. The highly complex phenomena taking place during Diesel and gasoline type combustion are covered by explicit approaches supported by testbed data. The impact of the thermodynamic characteristics induced by the different fuels is described by an appropriate set of transport equations in combination with specifically prepared property databases. A thermodynamic highly accurate 6-species approach is presented. Additionally, a 3-species and a 1-species transport approach relying on the assumption of a lumped fuel are investigated regarding accuracy and computational performance. The comparison of measured and simulated pressure and temperature traces shows very good agreement.

Modern diesel engines employ a multitude of strategies for oxides of nitrogen (NOx) emission abatement, with exhaust gas recirculation (EGR) being one of the most effective technique. The need for a precise control on the intake charge dilution (as a result of EGR) is paramount since small fluctuations in the intake charge dilution at high EGR rates may cause larger than acceptable spikes in NOx/soot emissions or deterioration in the combustion efficiency, especially at low to mid-engine loads. The control problem becomes more pronounced during transient engine operation; currently the trend is to momentarily close the EGR valve during tip-in or tip-out events. Therefore, there is a need to understand the transient EGR behaviour and its impact on the intake charge development especially under unstable combustion regimes such as low temperature combustion.

When comparing automotive and large-bore diesel engines, the latter usually show lower specific fuel consumption values, while automotive engines are subject to much stricter emission standards. Within an FVV (Research Association for Combustion Engines) project these differences were identified, quantified and assigned to individual design and operation parameters. The approach was split in three different phases: 1 Comparison of different-sized diesel engines 2 Correlation of differences in fuel consumption to design and operating parameters 3 Further investigations under automotive boundary conditions The comparison in the first phase was made on the basis of operating data and energy balances as well as the separation of losses based on the thermodynamic analysis. To also determine the quantitative effects of each design and operating parameter, a 1D process calculation model of the passenger car engine was transformed gradually to a large-bore engine in the second phase.

Conventional crank-based engines are limited by mechanical, thermal, and combustion inefficiencies. The free piston of a linear engine generator reduces frictional losses by avoiding the rotational motion and crankshaft linkages. Instead, electrical power is generated by the oscillation of a translator through a linear stator. Because the free piston is not geometrically constrained, dead center positions are not specifically known. This results in a struggle against adverse events like misfire, stall, over-fueling, or rapid load changes. It is the belief that incorporating springs will have the dual benefit of increasing frequency and providing a restoring force to aid in greater cycle to cycle stability. For dual free piston linear engines the addition of springs has not been fully explored, despite growing interest and literature.

In the paper the results of an experimental campaign regarding the steady characterization of a turbocharger waste-gated turbine (IHI-RHF3) for gasoline engine application are presented. The turbine behavior is analyzed in a specialized test rig operating at the University of Genoa, under different openings of the waste-gate valve. The test facility allows to measure inlet and outlet static pressures, mass flow rate and turbocharger rotational speed. The above data constitute the basis for the tuning and validation of a numerical procedure, recently developed at the University of Naples, following a 1D approach (1D turbine model - 1DTM). The model geometrically schematizes the entire turbine based on few linear and angular dimensions directly measured on the hardware. The 1D steady flow equations are then solved within the stationary and rotating channels constituting the device. All the main flow losses are properly taken into account in the model.

Boosting technologies have been key enablers for automotive engines development through downsizing and downspeeding. In this situation, numerous multistage boosting systems have appeared in the last decade. The complexity arising from multistage architectures requires an efficient matching methodology to obtain the best overall powertrain performance. The paper presents a model aimed to choose the best 2-stage boosting system architecture able to meet required criteria on boosting pressure, EGR ratios for both short and long route loops while respecting the engine thermo-mechanical limits such as in-cylinder pressure, compressor outlet temperature and exhaust manifold temperature. The model includes filling-and-emptying 0D elements together with mean value. The engine model is set in a way that, for given requirements and boosting system layout, calculates in seconds if the requirements will be achieved and the position of variable geometry, waste-gate, EGR and by-pass valves.

Piston rings are large contributors to friction losses in internal combustion engines. To achieve higher engine efficiency, low friction ring packs that can maintain good sealing performance must be designed. To support this effort, simulation tools have been developed to model the performance of piston rings during engine operation. However, the challenge of predicting oil consumption, blow by, and ring pack friction with sufficient accuracy remains. This is mostly due to the complexity of this system. Ring dynamics, deformation, interaction with liner and piston, gas and lubricant flow must all be studied together to make relevant predictions. In this paper, a new curved beam finite element model of piston rings is proposed. Ring structural deformation and contact with the liner are treated on two separate grids. A comparison with ring models in the literature and analytical solutions shows that it can provide accurate results efficiently.

Manufacturers have been considering various technology options to improve vehicle fuel economy. Some of the most promising technologies are related to vehicle electrification. To evaluate the benefits of vehicle electrification to support the 2017-2025 CAFE regulations, a study was conducted to simulate many of the most common electric drive powertrains currently available on the market: 12V Micro Hybrid Vehicle (start/stop systems), Belt-integrated starter generator (BISG), Crank-integrated starter generator (CISG), Full Hybrid Electric Vehicle (HEV), PHEV with 20-mile all-electric range (AER) (PHEV20), PHEV with 40-mile AER (PHEV40), Fuel-cell HEV and Battery Electric vehicle with 100-mile AER (EV100). Different vehicle classes were also analyzed in the study process: Compact, Midsize, Small SUV, Midsize SUV and Pickup. This paper will show the fuel displacement benefit of each powertrain across vehicle classes.

Detailed chemistry and turbulence-chemistry interaction need to be properly taken into account for a realistic combustion simulation of IC engines where advanced combustion modes, multiple injections and stratified combustion involve a wide range of combustion regimes and require a proper description of several phenomena such as auto-ignition, flame stabilization, diffusive combustion and lean premixed flame propagation. To this end, different approaches are applied and the most used ones rely on the well-stirred reactor or flamelet assumption. However, well-mixed models do not describe correctly flame structure, while unsteady flamelet models cannot easily predict premixed flame propagation and triple flames. A possible alternative for them is represented by transported probability density functions (PDF) methods, which have been applied widely and effectively for modeling turbulent reacting flows under a wide range of combustion regimes.

This paper presents an automated fit for a control-oriented physics-based diesel engine combustion model. This method is based on the combination of a dedicated measurement procedure and structured approach to fit the required combustion model parameters. Only a data set is required that is considered to be standard for engine testing. The potential of the automated fit tool is demonstrated for two different heavy-duty diesel engines. This demonstrates that the combustion model and model fit methodology is not engine specific. Comparison of model and experimental results shows accurate prediction of in-cylinder peak pressure, IMEP, CA10, and CA50 over a wide operating range. This makes the model suitable for closed-loop combustion control development. However, NO emission prediction has to be improved.