Search Results

In this study we identify components of a typical biodiesel fuel and estimate both their individual and mixed thermo-physical and transport properties. We then use the estimated mixture properties in computational simulations to gauge the extent to which combustion is modified when biodiesel is substituted for conventional diesel fuel. Our simulation studies included both conventional diesel combustion (DI) and premixed charge compression ignition (PCCI). Preliminary results indicate that biodiesel ignition is significantly delayed due to slower liquid evaporation, with the effects being more pronounced for DI than PCCI. The lower vapor pressure and higher liquid heat capacity of biodiesel are two key contributors to this slower rate of evaporation. Other physical properties are more similar between the two fuels, and their impacts are not clearly evident in the present study.

An experimental method was set up in a single cylinder optical engine in GDI configuration to study UHC origins in both homogeneous and stratified operation. On the one hand, UHC were observed in the combustion chamber by formaldehyde LIF (excitation at 355 nm and collection from 400 to 470 nm). Formaldehyde is a natural UHC tracer since it results from partly decomposed fuel that has not been fully oxidized during combustion. A quartz cylinder liner was used in order to benefit from a large optical access. On the other hand, UHC emissions measurement were simultaneously performed with a fast FID analyzer whose sampling probe was located 2 cm downstream the exhaust valve, in one of the two exhaust ports. An instantaneous exhaust mass flow model was also developed using 0-D simulation. The computed mass flow rate was coupled to fast FID measurements to estimate instantaneous and cycle to cycle UHC emissions.

Extensive literature exists on spray development, mixing and combustion regarding engine modeling and diagnostics using single-component and model fuels. However, often the variation in data between different fuels, particularly relating to spray development and its effect on combustion, is neglected or overlooked. By injecting into a quiescent chamber, this work quantifies the differences in spray development from a multi-hole direct-injection spark-ignition engine injector for two single-component fuels (iso-octane and n-pentane), a non-fluorescing multi-component model fuel which may be used for in-cylinder Laser Induced Fluorescence experiments, and several grades of pump gasoline (with and without additives). High-speed recordings of the sprays were made for a range of fuel temperatures and gas pressures. It is shown that a fuel temperature above that of the lowest boiling point fraction of the tested fuel at the given gas pressure causes a convergence of the spray plumes.

Hydrotreated vegetable oil (HVO) named NExBTL is a 2nd generation renewable diesel fuel made by a refinery-based process converting vegetable oils to paraffins. Also animal fats are suitable for feedstocks. Properties of this non-ester type biobased fuel are very similar to GTL. It contains no sulfur, oxygen, nitrogen or aromatics. Cetane number is very high (∼90). Cloud point can be adjusted by severity of the process from -5 to -30°C, heating value is similar to diesel fuel, storage stability is good, and water solubility is low. Emissions of two heavy duty engines and two city buses are presented with HVO and sulfur free EN 590 diesel fuel. The effect of HVO on regulated emissions compared to EN 590 fuel was: NOx -7 % … -14 % PM -28 % … -46 % CO -5 % … -78 % HC 0 % … -48 % Aldehydes, PAHs, mutagenicity and particulate size were also measured.

The contribution to the engine-out hydrocarbon (HC) emissions from fuel that escapes the main combustion event in piston ring crevices was estimated for an air-cooled, V-twin utility engine. The engine was run with a homogeneous pre-vaporized mixture system that avoids the presence of liquid films in the cylinder, and their resulting contribution to the HC emissions. A simplified ring pack gas flow model was used to estimate the ring pack contribution to HC emissions; the model was tested against the experimentally measured blowby. At high load conditions the model shows that the ring pack returns to the cylinder a mass of HC that exceeds that observed in the exhaust, and thus, is the dominant contributor to HC emissions. At light loads, however, the model predicts less HC mass returned from the ring pack than is observed in the exhaust. Time-resolved HC measurements were performed and used to assess the effect of combustion quality on HC emissions.

By changing the top-land radial clearance, this paper presents the effect of the piston crevice on the transient HC emissions of the first firing cycle at cold start on an LPG SI Engine. A fast-response flame ionization detector (FFID) was employed to measure transient HC emissions of the first firing cycle. At the same time, the transient cylinder pressure and instantaneous crankshaft speed of the engine were measured and recorded. The results show that increasing 50% crevice volume leads to 25% increase of HC emissions in the lean region and 18% increase of HC emissions in the rich region, however, the 50% increase of crevice volume contributes to 32% decease of HC emissions in the stable combustion region. For LPG SI engine, the HC emissions of the first firing cycle during cold start are relatively low in a wide range of the excess air ratio.

In this study different methods to reduce the soot emissions of Diesel engines were investigated and compared to obtain their soot reduction potential. Apart from investigations on the practically usable engine map area with so called homogeneous charge compression ignition (HCCI) combustion processes a new heterogeneous combustion processes was developed and investigated which offers significantly reduced soot emissions while still applicable in the entire engine map. For the HCCI experiments the emphasis was put on the achievable engine load range when using conventional injector nozzles which still allow a conventional heterogeneous engine operation.

In-cylinder and exhaust soot mass were measured in an optically accessible heavy duty diesel engine under various intake oxygen concentrations from 8 vol% to 21 vol% to gain insight into soot formation and destruction processes. Exhaust-gas recirculation (EGR) in the optical engine was simulated by dilution of intake gases with nitrogen. In-cylinder soot, measured by 2-color optical pyrometry, was compared to engine-out soot, measured by a commercial optical smoke meter. Each EGR rate was studied under two separate fueling conditions: (i) constant injection duration, and (ii) constant global equivalence ratio. The in-cylinder and exhaust soot measurements of the current study agree well with findings of previous studies in the literature. Under both fueling conditions, in-cylinder soot temperatures decreased with the reduction of in-cylinder oxygen concentration.

The whirl noise on turbochargers is generated by the self-induced vibration of the oil film in the bearing system. The noise is characterized by its frequency behavior that doesn't increase proportionately to the turbo shaft speed. It tends to be felt annoying. In this paper, to improve the whirl vibration, a statistical analysis approach was applied to the bearing specifications. The results from experiments showed that the bearing clearances played an important role in the reduction of the whirl vibration. To further investigate into this phenomenon, the shaft oscillation behavior was measured. And a vibration simulation program for the turbocharger bearing system was also developed.

Flexibility in running with different fuel is becoming an important issue in the Internal Combustion Engine design due to the increasingly wider use of alternative fuels. The injection systems must deal with fuels having different properties and effects on engine behavior and take proper adjustments in the control strategy. Particularly the transient during which one fuel is being replaced by the second one is a critical point of the injection system operation, and its capability of recognizing the fuel mixture currently available is a fundamental matter in the engine control development. This paper focuses on the multidimensional CFD analysis of a Common Rail type multi-fuel injection system accumulator during the gasoline - ethanol shift. An open source computational fluid dynamics code was used in the modeling.

Thermal efficiency comparisons are made between the low temperature combustion and the conventional diesel cycles on a common-rail diesel engine with a conventional diesel fuel. Empirical studies have been conducted under independently controlled exhaust gas recirculation, intake boost, and exhaust backpressure. Up to 8 fuel injection pulses per cylinder per cycle have been applied to modulate the homogeneity history of the early injection diesel low temperature combustion operations in order to improve the phasing of the combustion process. The impact of heat release phasing, duration, shaping, and splitting on the thermal efficiency has been analyzed with zero-dimensional engine cycle simulations. This paper intends to identify the major parameters that affect diesel low temperature combustion engine thermal efficiency.

Fully flexible valve actuation (FFVA) system, often referred to as camless valvetrain, employs electronically controlled actuators to drive the intake and/or exhaust valves. This technology enables the engine controller to tailor the valve event according to the engine operating condition in real-time to improve fuel economy, emissions and performance. At GM Research and Development Center, we have developed laboratory electro-hydraulic FFVA systems for single cylinder gasoline engines. The objective of this work is to develop a FFVA system for advanced diesel combustion research. There are three major differences between gasoline and diesel engines in terms of applying the FFVA systems. First, the orientation of the diesel engine valves and the location of the fuel injection system complicate the packaging issue. Second, the clearance between the valves and the piston for diesel engines are extremely small.

Commingling of fuels containing various concentrations of ethanol can occur in a vehicle fuel tank. It was not possible to estimate the RVPs of commingled ethanol containing fuels because they form complex non-ideal solutions. A nomograph and an equation were developed using the theory and experimental data for estimating the RVP of a commingled ethanol fuel blend from the RVPs of two base fuels containing any amounts of ethanol. The model is also useful for general purpose estimation of vapor pressures of ethanol/gasoline blends such as seasonal blending of E85 fuels with the right vapor pressure gasoline and the right amount of ethanol to meet the seasonal fuel vapor pressure requirement.

The assessment of tighter and tighter emission targets, and the increase of efficiency of Diesel engines is pushing towards the need of oxidation catalysts capable of high conversion performance at very low temperatures. These capabilities can be achieved only by the adoption of very high noble metal loadings (up to 140 g/ft3), which lead to very high costs. Washcoat distribution may play a key role in this context. In this paper the influence of washcoat distribution on light-off behaviour of a Diesel Oxidation Catalyst has been then investigated by means of a 3D numerical model. The model is capable of representing the coupling among flow, washcoat diffusion and detailed surface chemistry. Results state that the adoption of an optimized washcoat distribution may roughly lead to cost-savings of the order 30-40% in terms of noble metal loading.

The described investigation was carried out under the umbrella of IEA Advanced Motor Fuels Agreement. The purpose was to evaluate the emissions of carbon monoxide (CO), unburned hydrocarbons (HC), nitrogen oxides (NOx), particulate matter (PM) and polycyclic aromatic hydrocarbons (PAH) from vehicles fuelled by Fischer Tropsch (FT) based diesel and gasoline fuel, compared to the emissions from ordinary diesel and gasoline. The comparison for diesel fuels was based on a literature review, whereas the gasoline comparison had to be based on our own experiments, since almost no references were found in this field. In this context measurement according to the Federal Test Procedure (FTP) and the New European Driving Cycle (NEDC) were carried out on a chassis dynamometer with a directly injected gasoline vehicle. Experiments were carried out with a reference fuel, a fuel based 70% on FT and an alkylate fuel (Aspen), which was taken to be the ultimate formula of FT gasoline.

This investigation includes a comparison of two Fischer Tropsch (FT) fuels derived from natural gas and a Rapeseed Methyl Ester (RME) fuel with Swedish low sulfur Diesel in terms of emissions levels, fuel consumption and combustion parameters. The engine used in the study was an AVL single cylinder heavy-duty engine, equipped with a cylinder head of a Volvo D12 engine. Two loads (25% and 100%) were investigated at a constant engine speed of 1200 rpm. The engine was calibrated to operate in different levels of EGR and with variable injections timings. A design of experiments was constructed to investigate the effects of these variables, and to identify optimal settings. The results showed that the soot emissions yielded by FT and RME fuels are up to 40 and 80 percent lower than those yielded by the Swedish Diesel. In addition the FT fuel gave slightly lower, and the RME significant higher NOx emissions than the Swedish Diesel.

The effect of biodiesel content on homogeneous charge compression ignition (HCCI) engine performance has been investigated both experimentally and by computer simulation. Combustion experiments were performed in a single cylinder HCCI engine using blends of soy biodiesel in ultra low sulfur diesel, with concentrations ranging from 0 to 50 vol% and equivalence ratios (Φ) from 0.38 to 0.48. Data from the engine tests included combustion analysis and exhaust composition analysis with standard gaseous emissions equipment. The engine utilized a custom port fuel injection strategy to provide highly premixed charges of fuel and air, making it possible to compare the results with single zone chemical kinetics simulations that were performed using CHEMKIN III, with a reaction set including 670 species and over 3000 reactions.

Seven biofuel-diesel fuel configurations were tested in a single-cylinder research diesel CFR engine that allowed variable injection timing. These seven configurations included three biodiesel-diesel blends (20% and 100%); two ethanol-diesel blends (15% and 20%), and two cases in which ethanol was injected into the intake air flow (20% and 33%). Combustion characteristics, NOx emissions, and soot emissions were compared with diesel operation across a range of injection timings. The effect of fuel compressibility affected the timing of injection, with biodiesel-diesel blends having advanced injection and ethanol-diesel blends having delayed injection. Biodiesel-diesel blends showed reduced ignition delay with only modest changes in combustion duration, while ethanol-diesel mixtures showed longer ignition delay but much shorter combustion duration and earlier phasing.

Understanding the processes regarding fuel injection, vaporization and combustion during cold start is very important in order to reduce the HC-emission of gasoline engines. To learn more about the cold engine start-up process an experimental study on a 4.2 liter eight cylinder engine with gasoline direct injection was carried out. Parameters such as injection and ignition timing as well as the injection quantity were varied to get information about their effect on the combustion process and speed rise. Especially during engine run-up it is important to investigate every subsequent combustion. Therefore the engine was equipped with high pressure indication in each cylinder. The transient pressures and the instantaneous crankshaft speed of the engine were recorded by means of an indication system. Additionally a fast response flame ionization detector (FRFID) was applied to measure the transient HC-emissions during the first cycles of the engine.

The effects of the directed port flow produced by a Charge-Motion-Control-Valve (CMCV) on mixture preparation in a Port-Fuel-Injection engine were assessed under conditions typical of fast idle in a cold start process. The port fuel was found to comprise two components: a “valve” puddle (at the vicinity of the valve) that built up quickly, and that was mainly responsible for the delivery of the fuel to the cylinder charge; a “port” puddle located significantly upstream. The latter was mainly created by the reverse back flow process and built up slowly. Although the fuel amounts in these two components were roughly the same, the latter did not significantly interact with the fuel transport to the cylinder charge. The CMCV only weakly affected the purging or filling time of the valve puddle, hence the dynamics of the fuel delivery process was not materially affected.