Refine Your Search

Topic

Search Results

Technical Paper

A New Approach to Occupant Simulation Through the Coupling of PC-Crash and MADYMO

1999-03-01
1999-01-0444
During recent years the accident simulation program PC-Crash was developed. This software simulates vehicle movement before, during and after the impact, using 3D vehicle and scene models. ...A new interface has been developed between MADYMO® and PC-Crash so that, after the reconstruction of an accident, only a few additional parameters regarding restraint system, seat and occupant must be defined. ...A new interface has been developed between MADYMO® and PC-Crash so that, after the reconstruction of an accident, only a few additional parameters regarding restraint system, seat and occupant must be defined. PC-Crash then creates all necessary input files for MADYMO® and starts the occupant simulation.
Technical Paper

Validation of a PC-Crash Multibody Sport Bike Motorcycle Model

2021-04-06
2021-01-0893
PC-Crash is an accident reconstruction program allowing the user to perform simulations with multibody objects that collide or interact with 3D vehicle mesh models. ...The current motorcycle models in PC-Crash are generic and do not resemble a sport bike type motorcycle. They are only globally scalable such that you cannot adjust length, width, or height independently. ...The test results were compared to parameters calculated in PC-Crash. Results such as Delta-V, yaw rate and overall post impact trajectories of the motorcycle, rider and movement of the target vehicle were compared to the data from the instrumented test vehicles.
Technical Paper

Validation of the Coupled PC-CRASH - MADYMO Occupant Simulation Model

2000-03-06
2000-01-0471
During recent years the accident simulation program PCCRASH was developed, which allows to simulate the vehicles movement before, during and after the impact. ...Within SAE 1999-01-0444 a new coupling interface of PC-CRASH and the software MADYMO, developed by TNO in the Netherlands was published. During last year's publication only few validation cases, mainly related to rear end impacts could be demonstrated. ...One major emphasis was set on the influence of the crash pulse, which cannot be derived in PC-CRASH. In this way the paper demonstrates the possibilities as well as the limitations of the numerical model.
Technical Paper

Application of the Monte Carlo Methods for Stability Analysis within the Accident Reconstruction Software PC-CRASH

2003-03-03
2003-01-0488
During recent years the accident simulation program PC-CRASH was developed, which allows simulating the vehicles movement before, during and after the impact. ...The first one serves as an alternative for the optimizer tool and is included in the current version of PC-Crash. It gives reasonable insight in the variation of certain parameters in reasonable calculation time.
Technical Paper

Pycrash: An Open-Source Tool for Accident Reconstruction

2021-04-06
2021-01-0896
In this paper, the current capabilities of Pycrash are illustrated and its accuracy is assessed using matching PC-Crash simulations performed using PC-Crash. The results indicate that Pycrash is well-equipped to perform fundamental accident reconstruction analyses, including impact related effects, but its simplified suspension model is a limitation.
Journal Article

Reconstructing Vehicle Dynamics from On-Board Event Data

2019-04-02
2019-01-0632
These predictions were generated by directly integrating the VCH data and by using the VCH data as inputs to PC-Crash simulations. The predicted positions and headings were then compared to the actual position and heading data measured using differential GPS synchronized to the VCH data record.
Technical Paper

Mobility in mining: Issues for road safety improvement

2021-03-26
2020-36-0125
The increase of mining activities in the northern regions of Chile has brought about a new environment in terms of mobility to those areas where this industry has moved forward. This change has not only affected road traffic accidents on public roads of the surrounding mines, but also the inner organization of the mining companies, which must fulfill strict regulations, achieving the highest levels of safety. Given this situation, the current road traffic accidentology with respect to the northern regions of Chile has been analyzed in this paper. The results of the analysis have shown the relevant weight of the human factor and the state of the infrastructure related to the number of road fatalities. Thus, this paper provides solutions to combine the existing driver-centered technologies together with GPS systems that can track the movement of several vehicles and the design of safety berms in mine haul roads to mitigate the number of fatalities associated with mining activity.
Technical Paper

Near and Far-Side Adult Front Passenger Kinematics in a Vehicle Rollover

2001-03-05
2001-01-0176
In this study, U.S. accident data was analyzed to determine interior contacts and injuries for front-seated occupants in rollovers. The injury distribution for belted and unbelted, non-ejected drivers and right front passengers (RFP) was assessed for single-event accidents where the leading side of the vehicle rollover was either on the driver or passenger door. Drivers in a roll-left and RFP in roll-right rollovers were defined as near-side occupants, while drivers in roll-right and RFP in roll-left rollovers were defined as far-side occupants. Serious injuries (AIS 3+) were most common to the head and thorax for both the near and far-side occupants. However, serious spinal injuries were more frequent for the far-side occupants, where the source was most often coded as roof, windshield and interior.
Technical Paper

Challenges in Simulation and Sensor Development for Occupant Protection in Rollover Accidents

2000-11-01
2000-01-C038
Automotive occupant safety continues to evolve. At present this area has gathered a strong consumer interest which the vehicle manufacturers are tapping into with the introduction of many new safety technologies. Initially, individual passive devices and features such as seatbelts, knee- bolsters, structural crush zones, airbags etc., were developed for to help save lives and minimize injuries in accidents. Over the years, preventive measures such as improving visibility, headlights, windshield wipers, tire traction etc., were deployed to help reduce the probability of getting into an accident. With tremendous new research and improvements in electronics, we are at the stage of helping to actively avoid accidents in certain situations as well as providing increased protection to vehicle occupants and pedestrians.
Technical Paper

Essential Considerations in Delta-V Determination

2001-10-01
2001-01-3165
While Delta-V has been one of the most used indicators of accident severity for vehicle occupants, its actual determination remains a mystery to many who refer to it and use it. Delta-V is a term of art applied to a rapid change in vehicle velocity caused by impact forces during a collision. The Delta-V is associated with the high decelerations, which cause it and are applied to the occupants through restraint systems and collisions with the interior of the vehicle. This paper will serve as a primer for those new to the subject and a review for those who are familiar with the subject. Previous works by the authors will be referenced and other pertinent literature and data sources will be discussed. The analytical methods and test data used to calculate Delta-V will be presented and the relationship between Delta-V and other measures of impact severity, such as Barrier Equivalent Velocity and Energy Equivalent Speed will be discussed. The use of air bag sensor data will be included.
Journal Article

Vehicle and Occupant Responses in a Friction Trip Rollover Test

2009-04-20
2009-01-0830
Objective: A friction rollover test was conducted as part of a rollover sensing project. This study evaluates vehicle and occupant responses in the test. Methods: A flat dolly carried a Saab 9-3 sedan laterally, passenger-side leading to a release point at 42 km/h (26 mph) onto a high-friction surface. The vehicle was equipped with roll, pitch and yaw gyros near the center of gravity. Accelerometers were placed at the vehicle center tunnel, A-pillar near the roof, B-pillar near the sill, suspension sub-frame and wheels. Five off-board and two on-board cameras recorded kinematics. Hybrid III dummies were instrumented for head and chest acceleration and upper neck force and moment. Belt loads were measured. Results: The vehicle release caused the tires and then wheel rims to skid on the high-friction surface. The trip involved roll angular velocities >300 deg/s at 0.5 s and a far-side impact on the driver’s side roof at 0.94 s. The driver was inverted in the far-side, ground impact.
Technical Paper

Comparisons of Devices for Measuring Acceleration vs. Time in Braking Tests

2008-04-14
2008-01-0180
The coefficient of friction between a vehicle's tires and the roadway is a key parameter in any accident reconstruction. With the proliferation of vehicle dynamics software, it is often important to have more details regarding the tires interaction with the road than simply the average deceleration rate. Devices which can provide the peak friction as the braking develops, along with the average deceleration during the fully developed sliding phase, are necessary. There are now products widely available to the accident reconstruction market which provides these parameters as well as detailed acceleration vs. time curves. The following products capable of providing these results were tested: Accelerex, Vericom VC3000, and two general purpose accelerometers made by Silicon Designs and Dimension Engineering. Tests were conducted on wet and dry asphalt surfaces using a variety of passenger vehicles and transit buses which confirmed the agreement between these devices.
Technical Paper

Empirical Testing of Vehicular Rotational Motion

2012-04-16
2012-01-0602
Vehicles often rotate during traffic collisions due to impact forces or excessive steering maneuvers. In analyzing these situations, accident reconstructionists need to apply accurate deceleration rates for vehicles that are both rotating and translating to a final resting position. Determining a proper rate of deceleration is a challenging but critical step in calculating energy or momentum-based solutions for analytical purposes. In this research, multiple empirical tests were performed using an instrumented vehicle that was subjected to induced rotational maneuvers. A Ford Crown Victoria passenger car was equipped with a modified brake system where selected wheels could be isolated. The tests were performed on a dry asphalt surface at speeds of approximately 50 mph. In each of the tests, the vehicle rotated approximately 180 degrees with the wheels on one side being completely locked.
Technical Paper

Driver Perception of Lateral Collision Threats

2020-04-14
2020-01-1198
Immediate collision hazards pose obvious threats to approaching drivers and therefore provoke emergency evasive responses. When the hazard is a vehicle intruding into the lane ahead, how its movement characteristics influence an approaching driver’s response is not well understood. This study examined the relationship between intruding vehicle motion and hazard perception. Seventeen subjects viewed first-person perspective recordings of a simulated vehicle travelling down a two-lane roadway containing several intersections with stop-controlled minor roads. Stopped vehicles were located at approximately half of the minor road intersections. Throughout the study, some vehicles (termed ‘intruders’) accelerated into the subject’s lane of travel at 1 of 6 pre-determined acceleration rates. Subjects were instructed to ‘brake’ their vehicle by pressing the space bar on a keyboard as soon as they perceived that a collision was imminent.
Technical Paper

An Evaluation of Rectified Bitmap 2D Photogrammetry with PC-Rect

1997-02-24
970952
Without good-quality measurements taken at the time of an accident the analyst is faced with the need to extract measurement data from incident scene photographs. This paper discusses the history and development of the mathematical model for two-dimensional (2D) single exposure analytical photogrammetry, presents the software PC-Rect, and compares the analytical results obtained with PC-Rect to survey results. The sensitivity of the analytical results to the variation in such parameters as subject distance, camera height, digital photograph resolution, and bitmap density is discussed. The concept of using the directly rectified scanned photograph in the reconstruction task is introduced, and the utility of performing the dynamic simulation directly on the rectified photograph is discussed.
Technical Paper

Documenting Scientific Visualizations and Computer Animations Used in Collision Reconstruction Presentations

1998-02-23
980018
Scientific visualizations and computer animations are frequently presented to show the results of simulation models or the opinions of a reconstructionist. In these cases it is important to properly document the graphical images being presented. Proper documentation depends somewhat on the methodologies used to produce the images, but every scientific visualization, computer animation, and computer generated image should be documented sufficiently to allow others to duplicate the images. There are also some basic data that should accompany any computer generated images that will reveal the basis of the motion for all primary objects being depicted. This paper presents some basic definitions and outlines the data that is required to document scientific visualizations and computer animations.
X