Refine Your Search

Topic

Search Results

Technical Paper

A New Approach to Occupant Simulation Through the Coupling of PC-Crash and MADYMO

1999-03-01
1999-01-0444
During recent years the accident simulation program PC-Crash was developed. This software simulates vehicle movement before, during and after the impact, using 3D vehicle and scene models. ...A new interface has been developed between MADYMO® and PC-Crash so that, after the reconstruction of an accident, only a few additional parameters regarding restraint system, seat and occupant must be defined. ...A new interface has been developed between MADYMO® and PC-Crash so that, after the reconstruction of an accident, only a few additional parameters regarding restraint system, seat and occupant must be defined. PC-Crash then creates all necessary input files for MADYMO® and starts the occupant simulation.
Technical Paper

Application of the Monte Carlo Methods for Stability Analysis within the Accident Reconstruction Software PC-CRASH

2003-03-03
2003-01-0488
During recent years the accident simulation program PC-CRASH was developed, which allows simulating the vehicles movement before, during and after the impact. ...The first one serves as an alternative for the optimizer tool and is included in the current version of PC-Crash. It gives reasonable insight in the variation of certain parameters in reasonable calculation time.
Journal Article

Verification of ABS Models Applied in Programs for Road Accident Simulation

2010-04-12
2010-01-0070
The objective of the paper is to present the results of verification of ABS models applied in PC-Crash and HVE (Human-Vehicle-Environment) computer programs in various road conditions. The aim was reached by comparison of the road tests results obtained and calculations performed using the programs for the same initial values of the measured variables.
Journal Article

Reconstructing Vehicle Dynamics from On-Board Event Data

2019-04-02
2019-01-0632
These predictions were generated by directly integrating the VCH data and by using the VCH data as inputs to PC-Crash simulations. The predicted positions and headings were then compared to the actual position and heading data measured using differential GPS synchronized to the VCH data record.
Technical Paper

Simulation and Testing of a Suite of Field Relevant Rollovers

2004-03-08
2004-01-0335
Automotive rollover is a complex mechanical phenomenon. In order to understand the mechanism of rollover and develop any potential countermeasures for occupant protection, efficient and repeatable laboratory tests are necessary. However, these tests are not well understood and are still an active area of research interest. It is not always easy or intuitive to estimate the necessary initial and boundary conditions for such tests to assure repeatability. This task can be even more challenging when rollover is a second or third event (e.g. frontal impact followed by a rollover). In addition, often vehicle and occupant kinematics need to be estimated a-priori, first for the safe operation of the crew and equipment safety, and second for capturing and recording the event. It is important to achieve the required vehicle kinematics in an efficient manner and thus reduce repetitive tests. Mathematical modeling of the phenomenon can greatly assist in understanding such kinematics.
Technical Paper

Development of CAE Methodology for Rollover Sensing Algorithm

2009-04-20
2009-01-0828
The Rollover CAE model is developed for Rollover sensing algorithm in this paper. By using suggested CAE model, it is possible to make sensing data of rollover test matrix and these data can be used for calibration of rollover sensing algorithm. Developed vehicle model consists of three parts: a vehicle parts, an occupant parts and a ground boundary conditions. The vehicle parts include detailed suspension model and FE structure model. The occupant parts include ATD (anthropomorphic test device) male dummy and restraint systems: Curtain Airbag and Seat-Belt. We find analytical value of the suspension model through correlation with vehicle drop test, simulate this model under the conditions of untripped (Embankment, Corkscrew) and tripped (Curb-Trip, Soil-Trip) rollover scenarios. Comparison of the simulation and experimental data shows that the simulation results of suggested CAE model can be substituted for the experimental ones in calibration of rollover sensing algorithm.
Standard

Rollover Testing Methods

2017-07-28
CURRENT
J2926_201707
The scope of this document is to provide an overview of the techniques found in the published literature for rollover testing and rollover crashworthiness evaluation at the vehicle and component levels. It is not a comprehensive literature review, but rather illustrates the techniques that are in use or have been used to evaluate rollover crashworthiness-related issues.
Technical Paper

Challenges in Simulation and Sensor Development for Occupant Protection in Rollover Accidents

2000-11-01
2000-01-C038
Automotive occupant safety continues to evolve. At present this area has gathered a strong consumer interest which the vehicle manufacturers are tapping into with the introduction of many new safety technologies. Initially, individual passive devices and features such as seatbelts, knee- bolsters, structural crush zones, airbags etc., were developed for to help save lives and minimize injuries in accidents. Over the years, preventive measures such as improving visibility, headlights, windshield wipers, tire traction etc., were deployed to help reduce the probability of getting into an accident. With tremendous new research and improvements in electronics, we are at the stage of helping to actively avoid accidents in certain situations as well as providing increased protection to vehicle occupants and pedestrians.
Technical Paper

Essential Considerations in Delta-V Determination

2001-10-01
2001-01-3165
While Delta-V has been one of the most used indicators of accident severity for vehicle occupants, its actual determination remains a mystery to many who refer to it and use it. Delta-V is a term of art applied to a rapid change in vehicle velocity caused by impact forces during a collision. The Delta-V is associated with the high decelerations, which cause it and are applied to the occupants through restraint systems and collisions with the interior of the vehicle. This paper will serve as a primer for those new to the subject and a review for those who are familiar with the subject. Previous works by the authors will be referenced and other pertinent literature and data sources will be discussed. The analytical methods and test data used to calculate Delta-V will be presented and the relationship between Delta-V and other measures of impact severity, such as Barrier Equivalent Velocity and Energy Equivalent Speed will be discussed. The use of air bag sensor data will be included.
Technical Paper

Comparisons of Devices for Measuring Acceleration vs. Time in Braking Tests

2008-04-14
2008-01-0180
The coefficient of friction between a vehicle's tires and the roadway is a key parameter in any accident reconstruction. With the proliferation of vehicle dynamics software, it is often important to have more details regarding the tires interaction with the road than simply the average deceleration rate. Devices which can provide the peak friction as the braking develops, along with the average deceleration during the fully developed sliding phase, are necessary. There are now products widely available to the accident reconstruction market which provides these parameters as well as detailed acceleration vs. time curves. The following products capable of providing these results were tested: Accelerex, Vericom VC3000, and two general purpose accelerometers made by Silicon Designs and Dimension Engineering. Tests were conducted on wet and dry asphalt surfaces using a variety of passenger vehicles and transit buses which confirmed the agreement between these devices.
Technical Paper

Empirical Testing of Vehicular Rotational Motion

2012-04-16
2012-01-0602
Vehicles often rotate during traffic collisions due to impact forces or excessive steering maneuvers. In analyzing these situations, accident reconstructionists need to apply accurate deceleration rates for vehicles that are both rotating and translating to a final resting position. Determining a proper rate of deceleration is a challenging but critical step in calculating energy or momentum-based solutions for analytical purposes. In this research, multiple empirical tests were performed using an instrumented vehicle that was subjected to induced rotational maneuvers. A Ford Crown Victoria passenger car was equipped with a modified brake system where selected wheels could be isolated. The tests were performed on a dry asphalt surface at speeds of approximately 50 mph. In each of the tests, the vehicle rotated approximately 180 degrees with the wheels on one side being completely locked.
Technical Paper

Documenting Scientific Visualizations and Computer Animations Used in Collision Reconstruction Presentations

1998-02-23
980018
Scientific visualizations and computer animations are frequently presented to show the results of simulation models or the opinions of a reconstructionist. In these cases it is important to properly document the graphical images being presented. Proper documentation depends somewhat on the methodologies used to produce the images, but every scientific visualization, computer animation, and computer generated image should be documented sufficiently to allow others to duplicate the images. There are also some basic data that should accompany any computer generated images that will reveal the basis of the motion for all primary objects being depicted. This paper presents some basic definitions and outlines the data that is required to document scientific visualizations and computer animations.
Technical Paper

An Evaluation of Rectified Bitmap 2D Photogrammetry with PC-Rect

1997-02-24
970952
Without good-quality measurements taken at the time of an accident the analyst is faced with the need to extract measurement data from incident scene photographs. This paper discusses the history and development of the mathematical model for two-dimensional (2D) single exposure analytical photogrammetry, presents the software PC-Rect, and compares the analytical results obtained with PC-Rect to survey results. The sensitivity of the analytical results to the variation in such parameters as subject distance, camera height, digital photograph resolution, and bitmap density is discussed. The concept of using the directly rectified scanned photograph in the reconstruction task is introduced, and the utility of performing the dynamic simulation directly on the rectified photograph is discussed.
Technical Paper

Reconstruction of Vehicle-Pedestrian Collisions Including an Unknown Point of Impact

2015-04-14
2015-01-1419
Numerous algebraic formulas and mathematical models exist for the reconstruction of vehicle speed of a vehicle-pedestrian collision using pedestrian throw distance. Unfortunately a common occurrence is that the throw distance is not known because no evidence exists to locate the point of impact. When this is the case almost all formulas and models lose their utility. The model developed by Han and Brach published by SAE in 2001 is an exception because it can reconstruct vehicle speed based on the distance between the rest positions of the vehicle and pedestrian. The Han-Brach model is comprehensive and contains crash parameters such as pedestrian launch angle, height of the center of gravity of the pedestrian at launch, pedestrian-road surface friction, vehicle-road surface friction, road grade angle, etc. Such an approach provides versatility and allows variations of these variables to be taken into account for investigation of uncertainty.
Technical Paper

Determination of Critical Speed, Slip Angle and Longitudinal Wheel Slip based on Yaw Marks Left by a Wheel with Zero Tire Pressure

2016-04-05
2016-01-1480
This article presents the results of an analysis of the yaw marks left by a car with normal pressure in all tires and then normal pressure in three tires and zero in one rear tire. The analysis is a continuation of research on influence of reduced tire pressure on car lateral dynamics in a passing maneuver, discussed in the SAE paper No. 2014-01-0466. Preliminary analysis of yaw marks has shown, that a wheel with zero pressure deposits a yaw mark whose geometry differs from the yaw mark made by a wheel with normal pressure based on which we could calculate: critical speed, slip angle and longitudinal wheel slip. The aim of the presented research was to analyze the yaw marks left by car with zero pressure in one rear wheel in order to check the possibility of determining the vehicle critical speed, slip angle and longitudinal wheel slip. It was reached by performing bench and road tests during which the vehicle motion parameters were recorded using GPS Data Logging System.
X