Search Results

During recent years the accident simulation program PC-Crash was developed. This software simulates vehicle movement before, during and after the impact, using 3D vehicle and scene models. ...A new interface has been developed between MADYMO® and PC-Crash so that, after the reconstruction of an accident, only a few additional parameters regarding restraint system, seat and occupant must be defined. ...A new interface has been developed between MADYMO® and PC-Crash so that, after the reconstruction of an accident, only a few additional parameters regarding restraint system, seat and occupant must be defined. PC-Crash then creates all necessary input files for MADYMO® and starts the occupant simulation.

PC-Crash is an accident reconstruction program allowing the user to perform simulations with multibody objects that collide or interact with 3D vehicle mesh models. ...The current motorcycle models in PC-Crash are generic and do not resemble a sport bike type motorcycle. They are only globally scalable such that you cannot adjust length, width, or height independently. ...The test results were compared to parameters calculated in PC-Crash. Results such as Delta-V, yaw rate and overall post impact trajectories of the motorcycle, rider and movement of the target vehicle were compared to the data from the instrumented test vehicles.

The introduction of this model eliminated prior limitations that PC-Crash had for simulating motorcycle motion. Within PC-Crash, a user-defined path can be established for a motorcycle, and the software will generate motion consistent with the user-defined path (within the limits of friction and stability) and calculate the motorcycle lean (roll) generated by following that path at the prescribed speed, braking, or acceleration levels. ...However, the model again did not utilize counter-steering to generate lean, and so it is unlikely that the steering inputs generated by PC-Crash would match the real-world steering inputs. Still, the PC-Crash single-track driver model will yield results that are typically adequate for a crash reconstruction or visualization. ...This paper validates the single-track vehicle driver model available in PC-Crash simulation software. The model is tested, and its limitations are described. The introduction of this model eliminated prior limitations that PC-Crash had for simulating motorcycle motion.

During recent years the accident simulation program PC-CRASH was developed, which allows simulating the vehicles movement before, during and after the impact. ...The first one serves as an alternative for the optimizer tool and is included in the current version of PC-Crash. It gives reasonable insight in the variation of certain parameters in reasonable calculation time.

Next, simulations in PC-Crash were performed, and the results were compared with those obtained in experiments.

In this paper, the current capabilities of Pycrash are illustrated and its accuracy is assessed using matching PC-Crash simulations performed using PC-Crash. The results indicate that Pycrash is well-equipped to perform fundamental accident reconstruction analyses, including impact related effects, but its simplified suspension model is a limitation.

The objective of the paper is to present the results of verification of ABS models applied in PC-Crash and HVE (Human-Vehicle-Environment) computer programs in various road conditions. The aim was reached by comparison of the road tests results obtained and calculations performed using the programs for the same initial values of the measured variables.

First, the roundabout driving safety evaluation based on the rollover propensity index calculated with the tire loads was performed through various PC-Crash simulation analysis. And, using the Taguchi method, which is a representative DOE method, major factors affecting the rollover index were set by type and the sensitivity analysis results were quantitatively obtained.

Sensor signals are derived using the PC-Crash tool, and characteristic features are identified. Insights derived from these events can aid in development of robust rollover detection algorithms and calibrations.

Reconstruction by PC-Crash was performed for all of the sampled cases. Pre-crash parameters were calculated by a MATLAB code.

The analyst may often turn to accident reconstruction software such as the various versions of SMAC and some impulse-momentum approaches like PC-Crash and VCRware. Within these programs there is a user-input variable often referred to as the inter-vehicle friction coefficient.

These predictions were generated by directly integrating the VCH data and by using the VCH data as inputs to PC-Crash simulations. The predicted positions and headings were then compared to the actual position and heading data measured using differential GPS synchronized to the VCH data record.

The software packages included in the studies presented in this paper are HVE (SIMON and EDSMAC4), PC-Crash and VCRware. This paper will present the results of the study, conducted using DOE, involving these models.

Automotive occupant safety continues to evolve. At present this area has gathered a strong consumer interest which the vehicle manufacturers are tapping into with the introduction of many new safety technologies. Initially, individual passive devices and features such as seatbelts, knee- bolsters, structural crush zones, airbags etc., were developed for to help save lives and minimize injuries in accidents. Over the years, preventive measures such as improving visibility, headlights, windshield wipers, tire traction etc., were deployed to help reduce the probability of getting into an accident. With tremendous new research and improvements in electronics, we are at the stage of helping to actively avoid accidents in certain situations as well as providing increased protection to vehicle occupants and pedestrians.