Refine Your Search

Topic

Author

Affiliation

Search Results

Technical Paper

Vehicle Acceleration Modeling in PC-Crash

2014-04-01
2014-01-0464
The research reported here offers a validation of this capability, demonstrating that PC-Crash can be used to realistically model the build-up of a vehicle's speed under maximal acceleration. ...In the research reported here, PC-Crash 9.0 was used to model the full-throttle acceleration capabilities of three vehicles with automatic transmissions - a 2006 Ford Crown Victoria Police Interceptor (CVPI), a 2000 Cadillac DeVille DTS, and a 2003 Ford F150. ...In each case, the full-throttle acceleration of the vehicles modeled in PC-Crash showed good agreement with the acceleration of the real vehicles in our road tests.
Technical Paper

The Trailer Simulation Model of PC-CRASH

1998-02-23
980372
The program PC-CRASH was developed for the reconstruction of vehicle accidents and considers pre-impact, collision and post-impact phases. ...The present paper describes the physical and mathematical model which was added recently to PC-CRASH in order to enable the simulation of the dynamic behavior of articulated vehicles (with both single and double axle semi-trailers and with steered trailers).
Technical Paper

A Comparison Study between PC-Crash Simulation and Instrumented Handling Maneuvers

2011-04-12
2011-01-1121
Lateral acceleration, roll angle, roll rate, and yaw rate vehicle response from PC-Crash were compared to the MSAI sensor data. The authors modeled 26 handling tests. PC-Crash appeared to be a reasonable tool for modeling gross vehicle response. ...This research compares vehicle dynamic simulations in PC-Crash 8.2 to data recorded during instrumented handling tests conducted by Mechanical Systems Analysis Incorporated (MSAI). ...Vehicle weight, center of gravity (c.g) position, suspension stiffness parameters, tire parameters, steering angle, and vehicle speed data provided by MSAI were used as input for the PC-Crash model. Lateral acceleration, roll angle, roll rate, and yaw rate vehicle response from PC-Crash were compared to the MSAI sensor data.
Technical Paper

Validation of a PC-Crash Multibody Sport Bike Motorcycle Model

2021-04-06
2021-01-0893
PC-Crash is an accident reconstruction program that allows the user to run simulations with multibody objects that collide or interact with 3D vehicle mesh models. ...The current motorcycle models in PC-Crash are limited to generic-type motorcycles. Furthermore, they are only globally scalable such that you cannot adjust length, width, or height independently. ...The testing results were compared to parameters calculated in the PC-Crash program. Results such as Delta-V, yaw rate and overall post impact trajectories of the motorcycle, rider, and movement of the target vehicle were compared.
Journal Article

Verification of ABS Models Applied in Programs for Road Accident Simulation

2010-04-12
2010-01-0070
The objective of the paper is to present the results of verification of ABS models applied in PC-Crash and HVE (Human-Vehicle-Environment) computer programs in various road conditions. The aim was reached by comparison of the road tests results obtained and calculations performed using the programs for the same initial values of the measured variables.
Technical Paper

An Examination of Equations Relating Motorcycle Impact Speed to Struck Vehicle Post-Impact Rotational Displacement

2021-04-06
2021-01-0895
The most general and comprehensive solution will be to use one of the widely-accepted accident reconstruction simulation programs – PC-Crash, HVE (the EDSMAC4 or SIMON modules), or Virtual CRASH. These software packages incorporate equations for calculating the velocity changes that occur when the vehicles collide and equations for calculating the post-impact motion of the vehicles.
Technical Paper

Field Effectiveness Calculation of Integrated Safety Systems

2011-04-12
2011-01-1101
The vehicle dynamics of all scenarios from the database will be simulated in PC-Crash, an accident-reconstruction software. Since the brake assist is obligatory from 2012 on, the system and its effect on each single accident scenario will be modeled.
Technical Paper

Methods of Occupant Kinematics Analysis in Automobile Crashes

2002-03-04
2002-01-0536
Understanding occupant kinematics is an important part of accident reconstruction, particularly with respect to injury causation. Injuries are generally sustained as the occupant interacts with the vehicle interior surfaces and is rapidly accelerated to the struck component's post-impact velocity. This paper describes some methods for assessing occupant kinematics in a collision, and discusses their limitations. A useful technique is presented which is based on free-body analysis and can be used to establish an occupant's path of motion relative to the vehicle, locate the point of occupant contact, and determine the occupant's velocity relative to that contact location.
Technical Paper

RASSI: A Systematic Approach for On-site Crash Investigations and In-depth Accident Data Collection in India

2013-01-09
2013-26-0031
India's growing trend of serious road accidents has created an urgent need to understand the primary factors involved in these crashes and in the resulting severe injuries and fatalities. In order to improve the safety of highways and automobiles for all road users, a consortium of safety researchers and vehicle manufacturers has come together to collect first-hand, detailed and consistent crash and injury data for traffic accidents on Indian roads. After three years of pilot studies, a methodology, called Road Accident Sampling System - India (RASSI), has been developed for conducting on-site crash investigations and collecting in-depth accident data on road accidents in India. The processes developed under RASSI to investigate onsite crashes and collect quality accident data suitable for detailed analysis are described. The program includes all types of traffic accidents with injury outcomes.
Technical Paper

Near and Far-Side Adult Front Passenger Kinematics in a Vehicle Rollover

2001-03-05
2001-01-0176
In this study, U.S. accident data was analyzed to determine interior contacts and injuries for front-seated occupants in rollovers. The injury distribution for belted and unbelted, non-ejected drivers and right front passengers (RFP) was assessed for single-event accidents where the leading side of the vehicle rollover was either on the driver or passenger door. Drivers in a roll-left and RFP in roll-right rollovers were defined as near-side occupants, while drivers in roll-right and RFP in roll-left rollovers were defined as far-side occupants. Serious injuries (AIS 3+) were most common to the head and thorax for both the near and far-side occupants. However, serious spinal injuries were more frequent for the far-side occupants, where the source was most often coded as roof, windshield and interior.
Technical Paper

Occupant Friction Coefficients on Various Combinations of Seat and Clothing

2009-06-11
2009-01-1672
This paper reports on tests conducted to determine static and dynamic coefficients of friction between occupant clothing and automotive seat upholstery materials. Multiple materials were used for both the occupants clothing and the seat upholstery to examine friction variations with various material combinations. A fixture was fabricated to hold an automotive seat stationary while a dummy was pulled forward off of the seat. The forces required to pull the dummy were recorded for the various upholstery and clothing materials and the coefficients of friction were determined.
Technical Paper

Real-world car accident reconstruction methods for crash avoidance system research

2000-06-12
2000-05-0221
Development of crash avoidance systems and active safety systems must not be only based on experimental knowledge. The goal is to provide an efficient answer to still unsolved severe real-world car crashes which occur despite enhanced passive safety devices. This requires to know precisely the pre-crash conditions during about 3 to 10 seconds before impact. The paper describes the multidisciplinary systemic approach leading to the comprehensive methodology used in accident reconstruction in order to determine the best scenario, and to assess initial car speeds, paths and events in the different phases of the accident. This has already been carried out for about 400 car crashes with car occupant injuries (including 6% fatal and 10% severely injured). The necessity of collecting data on the spot of the crash scene is highlighted. Three well-trained investigators are involved.
Technical Paper

Rollover Crash Sensing and Safety Overview

2004-03-08
2004-01-0342
This paper provides an overview of rollover crash safety, including field crash statistics, pre- and rollover dynamics, test procedures and dummy responses as well as a bibliography of pertinent literature. Based on the 2001 Traffic Safety Facts published by NHTSA, rollovers account for 10.5% of the first harmful events in fatal crashes; but, 19.5% of vehicles in fatal crashes had a rollover in the impact sequence. Based on an analysis of the 1993-2001 NASS for non-ejected occupants, 10.5% of occupants are exposed to rollovers, but these occupants experience a high proportion of AIS 3-6 injury (16.1% for belted and 23.9% for unbelted occupants). The head and thorax are the most seriously injured body regions in rollovers. This paper also describes a research program aimed at defining rollover sensing requirements to activate belt pretensioners, roof-rail airbags and convertible pop-up rollbars.
Technical Paper

Challenges in Simulation and Sensor Development for Occupant Protection in Rollover Accidents

2000-11-01
2000-01-C038
Automotive occupant safety continues to evolve. At present this area has gathered a strong consumer interest which the vehicle manufacturers are tapping into with the introduction of many new safety technologies. Initially, individual passive devices and features such as seatbelts, knee- bolsters, structural crush zones, airbags etc., were developed for to help save lives and minimize injuries in accidents. Over the years, preventive measures such as improving visibility, headlights, windshield wipers, tire traction etc., were deployed to help reduce the probability of getting into an accident. With tremendous new research and improvements in electronics, we are at the stage of helping to actively avoid accidents in certain situations as well as providing increased protection to vehicle occupants and pedestrians.
Technical Paper

Modeling of Occupant Impacts During Rollover Collisions

2000-03-06
2000-01-0854
This paper describes a modeling method whereby the occupant impacts during rollover collisions may be predicted with sufficient accuracy to predict their injury level. By using MADYMO to reconstruct the vehicle motions during a rollover collision and the subsequent vehicle accelerations, the model may also be used to calculate occupant impact accelerations if reasonable estimates of interior surface stiffnesses are used.
Technical Paper

ASSESSMENT OF THE USE OF SEAT BELTS IN BUSES BASED ON RECENT ROAD TRAFFIC ACCIDENTS IN SPAIN

2001-06-04
2001-06-0019
The most important topic in the field of passive safety of buses and coaches nowadays is the future compulsory use of seat belts. The objective of the study performed by IDIADA AUTOMOTIVE TECHNOLOGY SA and CENTRO ZARAGOZA is to make an important contribution to the existing technical data about this subject. This paper is based on the in-depth analysis of recent road traffic accidents where buses were involved. The first step is the accident reconstruction. A complete injury report including description and causes of occupant injuries is the basis for the correlation of a computer simulation model. Experience in the development of coach seats equipped with seat belts enables the preparation of a comparative model. The hypothesis that the consequences of the accident could have been less severe if the occupants of the bus had worn a seat belt can be evaluated. The conclusions will help the legislators make the right decision.
Journal Article

Vehicle and Occupant Responses in a Friction Trip Rollover Test

2009-04-20
2009-01-0830
Objective: A friction rollover test was conducted as part of a rollover sensing project. This study evaluates vehicle and occupant responses in the test. Methods: A flat dolly carried a Saab 9-3 sedan laterally, passenger-side leading to a release point at 42 km/h (26 mph) onto a high-friction surface. The vehicle was equipped with roll, pitch and yaw gyros near the center of gravity. Accelerometers were placed at the vehicle center tunnel, A-pillar near the roof, B-pillar near the sill, suspension sub-frame and wheels. Five off-board and two on-board cameras recorded kinematics. Hybrid III dummies were instrumented for head and chest acceleration and upper neck force and moment. Belt loads were measured. Results: The vehicle release caused the tires and then wheel rims to skid on the high-friction surface. The trip involved roll angular velocities >300 deg/s at 0.5 s and a far-side impact on the driver’s side roof at 0.94 s. The driver was inverted in the far-side, ground impact.
X