Refine Your Search

Topic

Search Results

Technical Paper

Vehicle Acceleration Modeling in PC-Crash

2014-04-01
2014-01-0464
The research reported here offers a validation of this capability, demonstrating that PC-Crash can be used to realistically model the build-up of a vehicle's speed under maximal acceleration. ...In the research reported here, PC-Crash 9.0 was used to model the full-throttle acceleration capabilities of three vehicles with automatic transmissions - a 2006 Ford Crown Victoria Police Interceptor (CVPI), a 2000 Cadillac DeVille DTS, and a 2003 Ford F150. ...In each case, the full-throttle acceleration of the vehicles modeled in PC-Crash showed good agreement with the acceleration of the real vehicles in our road tests.
Technical Paper

The Collision and Trajectory Models of PC-CRASH

1996-02-01
960886
This paper presents the trajectory and collision models on which PC-CRASH is based. PC-CRASH'S model for predicting the 3D kinematics of a vehicle's pre- and post-impact trajectory, which is based on a discrete- kinetic time forward simulation of vehicle dynamics rather than empirically-derived “spin-out coefficients”, is described. ...PC-CRASH is a windowso-based accident-reconstruction program which combines the simulation of pre-collision, collision, and post-collision dynamics for multiple vehicles in a graphical environment.
Technical Paper

A Comparison Study between PC-Crash Simulation and Instrumented Handling Maneuvers

2011-04-12
2011-01-1121
Lateral acceleration, roll angle, roll rate, and yaw rate vehicle response from PC-Crash were compared to the MSAI sensor data. The authors modeled 26 handling tests. PC-Crash appeared to be a reasonable tool for modeling gross vehicle response. ...This research compares vehicle dynamic simulations in PC-Crash 8.2 to data recorded during instrumented handling tests conducted by Mechanical Systems Analysis Incorporated (MSAI). ...Vehicle weight, center of gravity (c.g) position, suspension stiffness parameters, tire parameters, steering angle, and vehicle speed data provided by MSAI were used as input for the PC-Crash model. Lateral acceleration, roll angle, roll rate, and yaw rate vehicle response from PC-Crash were compared to the MSAI sensor data.
Technical Paper

A New Approach to Occupant Simulation Through the Coupling of PC-Crash and MADYMO

1999-03-01
1999-01-0444
During recent years the accident simulation program PC-Crash was developed. This software simulates vehicle movement before, during and after the impact, using 3D vehicle and scene models. ...A new interface has been developed between MADYMO® and PC-Crash so that, after the reconstruction of an accident, only a few additional parameters regarding restraint system, seat and occupant must be defined. ...A new interface has been developed between MADYMO® and PC-Crash so that, after the reconstruction of an accident, only a few additional parameters regarding restraint system, seat and occupant must be defined. PC-Crash then creates all necessary input files for MADYMO® and starts the occupant simulation.
Technical Paper

Effective Numerical Simulation Tool for Real-World Rollover Accidents by Combining PC-Crash and FEA

2007-04-16
2007-01-1773
In this work, we focused on the trip-over type, which occurs most frequently, and performed simulations to reproduce real-world rollover accidents by combining PC-Crash and FEA. At first, using a simplified full car model, sufficient conditions, such as additional velocity, required for a curb trip-over accident to occur, were derived from energy balance concept based on the same principle as critical sliding velocity (CSV) criterion. ...Based on rigid body dynamics, PC-Crash software was chosen to make an accident reconstruction analysis of some selected cases chosen from an accident database (NASS-CDS). ...The output of this PC-crash simulation was then used as the initial input conditions (i.e., speed, deceleration, etc.) of a detailed finite element analysis.
Technical Paper

Soil Trip Rollover Simulation and Occupant Kinematics in Real World Accident

2007-08-05
2007-01-3680
In this work, we focused on the trip-over type, which occurs most frequently, and performed simulations to reproduce real-world rollover accidents by combining PC-Crash and FEA. Soil trip-over simulation was carried out based on real world accidents. Based on rigid body dynamics, PC-Crash software was chosen to make an accident reconstruction analysis of some selected cases chosen from an accident database (NASS-CDS). ...Based on rigid body dynamics, PC-Crash software was chosen to make an accident reconstruction analysis of some selected cases chosen from an accident database (NASS-CDS). ...The output of this PC-crash simulation was then used as the initial input conditions (i.e., speed, deceleration, etc.) of a detailed finite element analysis.
Journal Article

Reconstructing Vehicle Dynamics from On-Board Event Data

2019-04-02
2019-01-0632
These predictions were generated by directly integrating the VCH data and by using the VCH data as inputs to PC-Crash simulations. The predicted positions and headings were then compared to the actual position and heading data measured using differential GPS synchronized to the VCH data record.
Technical Paper

Field Effectiveness Calculation of Integrated Safety Systems

2011-04-12
2011-01-1101
The vehicle dynamics of all scenarios from the database will be simulated in PC-Crash, an accident-reconstruction software. Since the brake assist is obligatory from 2012 on, the system and its effect on each single accident scenario will be modeled.
Technical Paper

Simulation and Testing of a Suite of Field Relevant Rollovers

2004-03-08
2004-01-0335
Automotive rollover is a complex mechanical phenomenon. In order to understand the mechanism of rollover and develop any potential countermeasures for occupant protection, efficient and repeatable laboratory tests are necessary. However, these tests are not well understood and are still an active area of research interest. It is not always easy or intuitive to estimate the necessary initial and boundary conditions for such tests to assure repeatability. This task can be even more challenging when rollover is a second or third event (e.g. frontal impact followed by a rollover). In addition, often vehicle and occupant kinematics need to be estimated a-priori, first for the safe operation of the crew and equipment safety, and second for capturing and recording the event. It is important to achieve the required vehicle kinematics in an efficient manner and thus reduce repetitive tests. Mathematical modeling of the phenomenon can greatly assist in understanding such kinematics.
Technical Paper

ERRATUM

2014-04-01
2014-01-0464.01
Technical Paper

Development of CAE Methodology for Rollover Sensing Algorithm

2009-04-20
2009-01-0828
The Rollover CAE model is developed for Rollover sensing algorithm in this paper. By using suggested CAE model, it is possible to make sensing data of rollover test matrix and these data can be used for calibration of rollover sensing algorithm. Developed vehicle model consists of three parts: a vehicle parts, an occupant parts and a ground boundary conditions. The vehicle parts include detailed suspension model and FE structure model. The occupant parts include ATD (anthropomorphic test device) male dummy and restraint systems: Curtain Airbag and Seat-Belt. We find analytical value of the suspension model through correlation with vehicle drop test, simulate this model under the conditions of untripped (Embankment, Corkscrew) and tripped (Curb-Trip, Soil-Trip) rollover scenarios. Comparison of the simulation and experimental data shows that the simulation results of suggested CAE model can be substituted for the experimental ones in calibration of rollover sensing algorithm.
Standard

Rollover Testing Methods

2017-07-28
CURRENT
J2926_201707
The scope of this document is to provide an overview of the techniques found in the published literature for rollover testing and rollover crashworthiness evaluation at the vehicle and component levels. It is not a comprehensive literature review, but rather illustrates the techniques that are in use or have been used to evaluate rollover crashworthiness-related issues.
Technical Paper

Challenges in Simulation and Sensor Development for Occupant Protection in Rollover Accidents

2000-11-01
2000-01-C038
Automotive occupant safety continues to evolve. At present this area has gathered a strong consumer interest which the vehicle manufacturers are tapping into with the introduction of many new safety technologies. Initially, individual passive devices and features such as seatbelts, knee- bolsters, structural crush zones, airbags etc., were developed for to help save lives and minimize injuries in accidents. Over the years, preventive measures such as improving visibility, headlights, windshield wipers, tire traction etc., were deployed to help reduce the probability of getting into an accident. With tremendous new research and improvements in electronics, we are at the stage of helping to actively avoid accidents in certain situations as well as providing increased protection to vehicle occupants and pedestrians.
Technical Paper

Essential Considerations in Delta-V Determination

2001-10-01
2001-01-3165
While Delta-V has been one of the most used indicators of accident severity for vehicle occupants, its actual determination remains a mystery to many who refer to it and use it. Delta-V is a term of art applied to a rapid change in vehicle velocity caused by impact forces during a collision. The Delta-V is associated with the high decelerations, which cause it and are applied to the occupants through restraint systems and collisions with the interior of the vehicle. This paper will serve as a primer for those new to the subject and a review for those who are familiar with the subject. Previous works by the authors will be referenced and other pertinent literature and data sources will be discussed. The analytical methods and test data used to calculate Delta-V will be presented and the relationship between Delta-V and other measures of impact severity, such as Barrier Equivalent Velocity and Energy Equivalent Speed will be discussed. The use of air bag sensor data will be included.
Technical Paper

Modeling of Occupant Impacts During Rollover Collisions

2000-03-06
2000-01-0854
This paper describes a modeling method whereby the occupant impacts during rollover collisions may be predicted with sufficient accuracy to predict their injury level. By using MADYMO to reconstruct the vehicle motions during a rollover collision and the subsequent vehicle accelerations, the model may also be used to calculate occupant impact accelerations if reasonable estimates of interior surface stiffnesses are used.
Technical Paper

ASSESSMENT OF THE USE OF SEAT BELTS IN BUSES BASED ON RECENT ROAD TRAFFIC ACCIDENTS IN SPAIN

2001-06-04
2001-06-0019
The most important topic in the field of passive safety of buses and coaches nowadays is the future compulsory use of seat belts. The objective of the study performed by IDIADA AUTOMOTIVE TECHNOLOGY SA and CENTRO ZARAGOZA is to make an important contribution to the existing technical data about this subject. This paper is based on the in-depth analysis of recent road traffic accidents where buses were involved. The first step is the accident reconstruction. A complete injury report including description and causes of occupant injuries is the basis for the correlation of a computer simulation model. Experience in the development of coach seats equipped with seat belts enables the preparation of a comparative model. The hypothesis that the consequences of the accident could have been less severe if the occupants of the bus had worn a seat belt can be evaluated. The conclusions will help the legislators make the right decision.
Technical Paper

Modeling the Effects of Seat Belt Pretensioners on Occupant Kinematics During Rollover

2006-04-03
2006-01-0246
The results of a number of previous studies have demonstrated that seat-belted occupants can undergo significant upward and outward excursion during the airborne phase of vehicular rollover, which may place the occupant at risk for injury during subsequent ground contacts. Furthermore, testing using human volunteers, ATDs, and cadavers has shown that increasing tension in the restraint system prior to a rollover event may be of value for reducing occupant displacement. On this basis, it may be argued that pretensioning the restraint system, utilizing technology developed and installed primarily for improving injury outcome in frontal impacts, may modify restrained occupant injury potential during rollover accidents. However, the capacity of current pretensioner designs to positively impact the motion of a restrained occupant during rollover remains unclear.
Technical Paper

Comparisons of Devices for Measuring Acceleration vs. Time in Braking Tests

2008-04-14
2008-01-0180
The coefficient of friction between a vehicle's tires and the roadway is a key parameter in any accident reconstruction. With the proliferation of vehicle dynamics software, it is often important to have more details regarding the tires interaction with the road than simply the average deceleration rate. Devices which can provide the peak friction as the braking develops, along with the average deceleration during the fully developed sliding phase, are necessary. There are now products widely available to the accident reconstruction market which provides these parameters as well as detailed acceleration vs. time curves. The following products capable of providing these results were tested: Accelerex, Vericom VC3000, and two general purpose accelerometers made by Silicon Designs and Dimension Engineering. Tests were conducted on wet and dry asphalt surfaces using a variety of passenger vehicles and transit buses which confirmed the agreement between these devices.
Technical Paper

Accuracy and Sensitivity of Yaw Speed Analysis to Available Data

2019-04-02
2019-01-0417
Accident reconstructionists rarely have complete data with which to determine vehicle speed, and so the true value must be bracketed within a range. Previous work has shown the effect of friction uncertainty in determining speed from tire marks left by a vehicle in yaw. The goal of the current study was to assess improvements in the accuracy of vehicle speed estimated from yaw marks using progressively more scene and vehicle information. Data for this analysis came from staged S-turn maneuvers that in some cases led to rollover of sport utility vehicles. Initial speeds were first calculated using the critical curve speed (CCS) formula on the yaw marks from the first portion of the S-maneuver. Then computer simulations were performed with progressively more input data: i) the complete tire marks from the whole S-maneuver, ii) measured vehicle mass, iii) measured suspension stiffness and damping, and iv) measured steering history.
X