Refine Your Search

Topic

Search Results

Technical Paper

Analysis of a Dolly Rollover with PC-Crash

2009-04-20
2009-01-0822
The current capabilities of PC-Crash for rollover modeling are discussed and suggestions are made for how PC-Crash might be improved for modeling rollovers. ...This paper evaluates the use of PC-Crash simulation software for modeling the dynamics of a dolly rollover crash test. The specific test used for this research utilized a Ford sport utility vehicle and was run in accordance with SAE J2114. ...Next, the test was modeled using PC-Crash. The simulation was optimized to yield a reasonable fit with the actual test dynamics by changing the following parameters in PC-Crash: (1) the friction coefficient associated with each vehicle-to-ground impact; (2) the coefficient of restitution for vehicle-to-ground impacts; (3) the vehicle body stiffness; and (4) the vehicle suspension and damping.
Technical Paper

The Collision and Trajectory Models of PC-CRASH

1996-02-01
960886
This paper presents the trajectory and collision models on which PC-CRASH is based. PC-CRASH'S model for predicting the 3D kinematics of a vehicle's pre- and post-impact trajectory, which is based on a discrete- kinetic time forward simulation of vehicle dynamics rather than empirically-derived “spin-out coefficients”, is described. ...PC-CRASH is a windowso-based accident-reconstruction program which combines the simulation of pre-collision, collision, and post-collision dynamics for multiple vehicles in a graphical environment.
Technical Paper

How to Use PC-CRASH to Simulate Rollover Crashes

2004-03-08
2004-01-0341
This study focuses on one program, PC-CRASH. This program was developed to allow simulations of vehicle 3-dimensional movements before, during and after the impact.
Technical Paper

A Comparison Study between PC-Crash Simulation and Instrumented Handling Maneuvers

2011-04-12
2011-01-1121
Lateral acceleration, roll angle, roll rate, and yaw rate vehicle response from PC-Crash were compared to the MSAI sensor data. The authors modeled 26 handling tests. PC-Crash appeared to be a reasonable tool for modeling gross vehicle response. ...This research compares vehicle dynamic simulations in PC-Crash 8.2 to data recorded during instrumented handling tests conducted by Mechanical Systems Analysis Incorporated (MSAI). ...Vehicle weight, center of gravity (c.g) position, suspension stiffness parameters, tire parameters, steering angle, and vehicle speed data provided by MSAI were used as input for the PC-Crash model. Lateral acceleration, roll angle, roll rate, and yaw rate vehicle response from PC-Crash were compared to the MSAI sensor data.
Technical Paper

Validation of the Coupled PC-CRASH - MADYMO Occupant Simulation Model

2000-03-06
2000-01-0471
During recent years the accident simulation program PCCRASH was developed, which allows to simulate the vehicles movement before, during and after the impact. ...Within SAE 1999-01-0444 a new coupling interface of PC-CRASH and the software MADYMO, developed by TNO in the Netherlands was published. During last year's publication only few validation cases, mainly related to rear end impacts could be demonstrated. ...One major emphasis was set on the influence of the crash pulse, which cannot be derived in PC-CRASH. In this way the paper demonstrates the possibilities as well as the limitations of the numerical model.
Technical Paper

An Analytical Review and Extension of Two Decades of Research Related to PC-Crash Simulation Software

2018-04-03
2018-01-0523
PC-Crash is a vehicular accident simulation software that is widely used by the accident reconstruction community. ...The goal of this article is to review the prior literature that has addressed the capabilities of PC-Crash and its accuracy and reliability for various applications (planar collisions, rollovers, and human motion). ...In addition, this article aims to add additional analysis of the capabilities of PC-Crash for simulating planar collisions and rollovers. Simulation analysis of five planar collisions originally reported and analyzed by Bailey [2000] are reexamined.
Technical Paper

Effective Numerical Simulation Tool for Real-World Rollover Accidents by Combining PC-Crash and FEA

2007-04-16
2007-01-1773
In this work, we focused on the trip-over type, which occurs most frequently, and performed simulations to reproduce real-world rollover accidents by combining PC-Crash and FEA. At first, using a simplified full car model, sufficient conditions, such as additional velocity, required for a curb trip-over accident to occur, were derived from energy balance concept based on the same principle as critical sliding velocity (CSV) criterion. ...Based on rigid body dynamics, PC-Crash software was chosen to make an accident reconstruction analysis of some selected cases chosen from an accident database (NASS-CDS). ...The output of this PC-crash simulation was then used as the initial input conditions (i.e., speed, deceleration, etc.) of a detailed finite element analysis.
Technical Paper

Soil Trip Rollover Simulation and Occupant Kinematics in Real World Accident

2007-08-05
2007-01-3680
In this work, we focused on the trip-over type, which occurs most frequently, and performed simulations to reproduce real-world rollover accidents by combining PC-Crash and FEA. Soil trip-over simulation was carried out based on real world accidents. Based on rigid body dynamics, PC-Crash software was chosen to make an accident reconstruction analysis of some selected cases chosen from an accident database (NASS-CDS). ...Based on rigid body dynamics, PC-Crash software was chosen to make an accident reconstruction analysis of some selected cases chosen from an accident database (NASS-CDS). ...The output of this PC-crash simulation was then used as the initial input conditions (i.e., speed, deceleration, etc.) of a detailed finite element analysis.
Training / Education

Reconstruction and Analysis of Rollover Crashes of Light Vehicles

2020-11-02
For automotive engineers involved in crash reconstruction and analysis, a knowledge of basic accident reconstruction principles and techniques is essential, but often insufficient to answer all of the questions posed by design engineers, regulators, and lawyers. This seminar takes participants beyond the basics of accident reconstruction to physical models and analysis techniques that are unique to the reconstruction of single-vehicle rollover crashes.
Technical Paper

Simulation and Testing of a Suite of Field Relevant Rollovers

2004-03-08
2004-01-0335
Automotive rollover is a complex mechanical phenomenon. In order to understand the mechanism of rollover and develop any potential countermeasures for occupant protection, efficient and repeatable laboratory tests are necessary. However, these tests are not well understood and are still an active area of research interest. It is not always easy or intuitive to estimate the necessary initial and boundary conditions for such tests to assure repeatability. This task can be even more challenging when rollover is a second or third event (e.g. frontal impact followed by a rollover). In addition, often vehicle and occupant kinematics need to be estimated a-priori, first for the safe operation of the crew and equipment safety, and second for capturing and recording the event. It is important to achieve the required vehicle kinematics in an efficient manner and thus reduce repetitive tests. Mathematical modeling of the phenomenon can greatly assist in understanding such kinematics.
Technical Paper

Measuring and Modeling Suspensions of Passenger Vehicles

2013-04-08
2013-01-0774
Numerical parameters describing suspension stiffness and damping are required for 3D simulation of vehicle trajectories, but may not be available. This paper outlines a simple, portable method of measuring these properties with a coefficient of variation of 5% on stiffness. 24 of 26 vehicles tested were significantly stiffer in roll than pitch, complicating analyses with models that don't include anti-roll. Suspension parameters did not correlate with static wheel load distribution, and damping coefficient did not correlate with natural frequency. Computer simulations of the speed required to initiate rollover in an S-curve were highly sensitive to the suspension parameters used. When pre-impact tire marks and rollover distance were considered, the simulations became almost insensitive to suspension parameters.
Technical Paper

Development of CAE Methodology for Rollover Sensing Algorithm

2009-04-20
2009-01-0828
The Rollover CAE model is developed for Rollover sensing algorithm in this paper. By using suggested CAE model, it is possible to make sensing data of rollover test matrix and these data can be used for calibration of rollover sensing algorithm. Developed vehicle model consists of three parts: a vehicle parts, an occupant parts and a ground boundary conditions. The vehicle parts include detailed suspension model and FE structure model. The occupant parts include ATD (anthropomorphic test device) male dummy and restraint systems: Curtain Airbag and Seat-Belt. We find analytical value of the suspension model through correlation with vehicle drop test, simulate this model under the conditions of untripped (Embankment, Corkscrew) and tripped (Curb-Trip, Soil-Trip) rollover scenarios. Comparison of the simulation and experimental data shows that the simulation results of suggested CAE model can be substituted for the experimental ones in calibration of rollover sensing algorithm.
Technical Paper

Tire Models for Vehicle Dynamic Simulation and Accident Reconstruction

2009-04-20
2009-01-0102
Various vehicle dynamic simulation software programs have been developed for use in reconstructing accidents. Typically these are used to analyze and reconstruct preimpact and postimpact vehicle motion. These simulation programs range from proprietary programs to commercially available packages. While the basic theory behind these simulations is Newton's laws of motion, some component modeling techniques differ from one program to another. This is particularly true of the modeling of tire force mechanics. Since tire forces control the vehicle motion predicted by a simulation, the tire mechanics model is a critical feature in simulation use, performance and accuracy. This is particularly true for accident reconstruction applications where vehicle motions can occur over wide ranging kinematic wheel conditions. Therefore a thorough understanding of the nature of tire forces is a necessary aspect of the proper formulation and use of a vehicle dynamics program.
Standard

Rollover Testing Methods

2017-07-28
CURRENT
J2926_201707
The scope of this document is to provide an overview of the techniques found in the published literature for rollover testing and rollover crashworthiness evaluation at the vehicle and component levels. It is not a comprehensive literature review, but rather illustrates the techniques that are in use or have been used to evaluate rollover crashworthiness-related issues.
Technical Paper

Near and Far-Side Adult Front Passenger Kinematics in a Vehicle Rollover

2001-03-05
2001-01-0176
In this study, U.S. accident data was analyzed to determine interior contacts and injuries for front-seated occupants in rollovers. The injury distribution for belted and unbelted, non-ejected drivers and right front passengers (RFP) was assessed for single-event accidents where the leading side of the vehicle rollover was either on the driver or passenger door. Drivers in a roll-left and RFP in roll-right rollovers were defined as near-side occupants, while drivers in roll-right and RFP in roll-left rollovers were defined as far-side occupants. Serious injuries (AIS 3+) were most common to the head and thorax for both the near and far-side occupants. However, serious spinal injuries were more frequent for the far-side occupants, where the source was most often coded as roof, windshield and interior.
Technical Paper

A Comparison of Moment of Inertia Estimation Techniques for Vehicle Dynamics Simulation

1997-02-24
970951
The moments of inertia, in yaw, pitch, and roll, as well as the center of gravity height are necessary to successfully model the 3D dynamic behavior of vehicles before, during and after collision. A number of vehicle parameter estimation techniques have been developed and are currently in use in North America and Europe. Many parameters have been measured by NHTSA and others. The estimation techniques are compared to the available measured values, and recommendations are made for best estimating the parameters when measured values are not available. The sensitivity of 3D vehicle collision dynamics and trajectory simulation to variance in the moment of inertia is demonstrated.
X